MYSBootloader 1.3 pre-release & MYSController 1.0.0beta

[jkandasa]

@Алексей-Гусаров If you use MYSbootloader you should Reboot your node. AFAIK, MYSbootloader requires Reboot to get active.
You should configure firmware in node edit page and reboot the node.
Upload firmware works only for DualOptiboot

[Thar0l]

@jkandasa I've tried to reboot and have such rsponce:

Apr 28, 2016 02:49:44 PM	serial   0:GatewayNode Received Internal [Log message] send: 0-0-1-1 s=255,c=3,t=13,pt=0,l=0,sg=0,st=fail:
Apr 28, 2016 02:49:44 PM	serial   1:SensorNode	Sent Internal	[Reboot]

[jkandasa]

@Алексей-Гусаров It looks like your node is not in the range!

[Thar0l]

@jkandasa said:

@Алексей-Гусаров It looks like your node is not in the range!

It sends messages it really in is 0.5 meters from gw.

[jkandasa]

@Алексей-Гусаров can you reboot the node manually?

[Thar0l]

@jkandasa
I have this:

[Log message] read: 1-1-0 s=255,c=4,t=2,pt=6,l=6,sg=0:010002006202
[Log message] send: 0-0-1-1 s=255,c=4,t=3,pt=6,l=22,sg=0,st=ok:010002006302801481E090E00F90DF91CF910895FC01
[Log message] read: 1-1-0 s=255,c=4,t=2,pt=6,l=6,sg=0:010002006302
[Log message] send: 0-0-1-1 s=255,c=4,t=3,pt=6,l=22,sg=0,st=ok:0100020064021382128248EE53E060E070E044835583
[Log message] read: 1-1-0 s=255,c=4,t=2,pt=6,l=6,sg=0:010002006402
[Log message] send: 0-0-1-1 s=255,c=4,t=3,pt=6,l=22,sg=0,st=ok:0100020065026683778385ED91E09183808308951092
[Log message] read: 1-1-0 s=255,c=4,t=2,pt=6,l=6,sg=0:010002006502

And yes, it has been updated.
Thanks, OTA works now, allthought remote reboot doesn working.

[jkandasa]

@Алексей-Гусаров I could not guess why remote reboot is not working! (Gateway says "Failed to send reboot command to node"). After OTA update completion, try reboot from MyController.org GUI. It may work with new software.

[Thar0l]

@jkandasa I've tried and it didn't help.

[tekka]

@Алексей-Гусаров rebooting is only working if node is actively processing incoming msgs. Use wait() instead of sleep() within your loop()

[Thar0l]

@tekka @jkandasa
Thank you.
I've added

#define MY_REPEATER_FEATURE

line in Node code, and it is working now.

[Mark Swift]

Guys,

I'm trying to get this working on my ESP8266 gateway (using the latest development branch).

I've uploaded the 16mhz boot loader to an Arduino Nano clone but don't seem to see anything in MYScontroller. I realised that my gateway sketch had channel 125 specified, so took that out for testing as I believe the boot loader uses channel 76...

Do I need to change any fuse settings etc, what am I missing?

Many thanks in advance...

Mark

Edit: Got it working, fantastic!

[Mark Swift]

Is there a way I can change the channel from the default 76?

Also am I correct in thinking that for my Nano's I copy the bits (high, low, extended, lock, unlock) from the Arduino section at the top and replace the pasted lines from the tutorial as it seems to be for the UNO?

[rollercontainer]

is already answered in this therad...

http://forum.mysensors.org/topic/3453/mysbootloader-1-3-pre-release-myscontroller-1-0-0beta/35

[Mark Swift]

This post is deleted!

[novas]

I have same problem as @n1ck1355. Shetch upload works, data are send, but serial output doesn't work.

[Mark Swift]

I also have the same issues with no node serial output within the Arduino IDE....

[tekka]

@Mark-Swift @novas do you see any traffic over the air from that node? If yes, please post the log, specifically, I'm interested in bootloader messages.

[Mark Swift]

@tekka I apologise, in my case it was the bootloader delay I wasn't allowing for. Opening the serial monitor and being patient, it appears all is well. Apologies for the mistake!

[novas]

@tekka In my case there were two problems. First same as @Mark-Swift, bootloader deley. I didn't expect that it takes about 30 seconds. Second one was that my gateway didn't run. In this case bootloader is still running and serial output isn't provided.

[Anduril]

@tekka I tried to upload a sketch after flashing the new bootloader to an nano. I got te this:

avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x4b
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x4b
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x4b
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x4b
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x4b
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x4b
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x4b
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x4b
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x4b
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x4b

What is going on?
OTA update still testing. Updating for several minutes now (I thought the old bootloader and OTA update did not take that long).