Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

New ESP

Hoffan last edited by

Hi All

I find this page, To bad it didn't have MYS like an option, But work with
Domoticz.
http://www.esp8266.nu/index.php/Main_Page
Reply Quote 0
1 Reply Last reply
filipq last edited by

Hi Hoffan

looks like they working on it http://www.esp8266.nu/forum/viewtopic.php?f=6&t=427
Reply Quote 0
1 Reply Last reply

2
Posts

946
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3310
Views

No one has replied
MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

11

0
Votes

11
Posts

53
Views

@dpcons MQTT sounds intimidating and looks imitimidating when you see all of the options available. Here's the scenario: You want to send a message. That's the -m option followed by a space and the message between " " the location, topic, is a tree, -t option, separated by forward slash / eg. MyRootTopic/MyTopicsSub/MyTopicSubSub It's as easy as that if your broker, the MQTT service (program) is on the same computer as the sending program. Usually it's not. Specifiy the location, the host, of the broker with the -h option followed by the host name or IP address The retain option, -r is important but explaining it is beyone the scope of this message Receiving, subscribing, to a topic is just the same, but you wouldn't have the -m message If you subscribe from the command line, the subscribe function waits indefinitely for messages published to the subscribed topic (unless you use the -C option) ^C to terminate the command. A tamotized device with the MQTT configured will create a number of topics on the broker. Home Assistant will see this automatically, if you have the Tasmota and MQTT Integrations installed. The MySensors MQTT gateway takes care of MQTT communication for a MySensors device. Again the MySensors and MQTT integrations. I use both. -OSD
Gateway without a radio
Development • • OldSurferDude

3

0
Votes

3
Posts

29
Views

@OldSurferDude yes, just run the configure command with --my-transport=none
Saving last known good state, but not in EEPROM
Development • • OldSurferDude

6

0
Votes

6
Posts

33
Views

@OldSurferDude jus request counter states from controller on each reset, worked fine with Domoticz... or save in eeprom but increase location every write, on power up/reset search eeprom for largest value stored and carry on from that location, one long integer will fit 256 times in atmega328(p) eeprom, is that long enough for you ?
Radio waking up for no reason.
Development • • Sasquatch

3

0
Votes

3
Posts

37
Views

Over 4 years on, and my node ran continuously sending 4 messages every 5 minutes. It's 700mAh LiFePo4 battery voltage dropped from initial 3.45V to 3.24V, according to LiFePo4 voltge/SoC tables It's just under 40% left. 700*60% = 420mAh. 100 mAH per year. using library 2.40 and blob message I could cut usage to ~25mAh/year, not bad
Adding Listen only device to my system.
Development • • dpcons

5

0
Votes

5
Posts

19
Views

@mfalkvidd Thanks for the info!

New ESP

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

Gateway without a radio
Development • • OldSurferDude

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Radio waking up for no reason.
Development • • Sasquatch

Adding Listen only device to my system.
Development • • dpcons

33
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

New ESP

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

MQTT-Help me understand about the MQTT Gateway. Development • • dpcons

Gateway without a radio Development • • OldSurferDude

Saving last known good state, but not in EEPROM Development • • OldSurferDude

Radio waking up for no reason. Development • • Sasquatch

Adding Listen only device to my system. Development • • dpcons

33Online

11.7kUsers

11.2kTopics

113.0kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

Gateway without a radio
Development • • OldSurferDude

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Radio waking up for no reason.
Development • • Sasquatch

Adding Listen only device to my system.
Development • • dpcons

33
Online

11.7k
Users

11.2k
Topics

113.0k
Posts