Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

RFM69 Driver

lafleur last edited by

It appears that the RFM69 driver in the 2.0b is (Older) different from the current driver from lowpower labs?

https://github.com/LowPowerLab/RFM69

Has anyone looked at or tested the driver as they apply to MySensor 2.0b??

Any plans on updating the driver for 2.0b release??
Reply Quote 0
1 Reply Last reply

1
Posts

746
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3307
Views

No one has replied
Saving last known good state, but not in EEPROM
Development • • OldSurferDude

6

0
Votes

6
Posts

32
Views

@OldSurferDude jus request counter states from controller on each reset, worked fine with Domoticz... or save in eeprom but increase location every write, on power up/reset search eeprom for largest value stored and carry on from that location, one long integer will fit 256 times in atmega328(p) eeprom, is that long enough for you ?
LAN8720A - will mysensors work with this module
Development • • Marcin

3

0
Votes

3
Posts

20
Views

Thanks for the answer. I meant that Mysensors has ESP32 support but only in terms of WIFI. It supports e.g. stm32 with ENC or W5500 modules - and the question is whether and how to add ESP32 support with LAN8720 module. I am not considering using ESPHOME or MQTT - I want to have native communication with the controller that implements my control schemes on its side. I try to program KC868-A16 but it does not matter - the question is whether such support can be added in a simple way.
MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

6

0
Votes

6
Posts

28
Views

@bgunnarb I like @eiten 's solution for you. Personally, I am not a fan of using cloud/public brokers. Thus I am curious about your system and there is something about it from which I can learn. I would like to understand why you cannot deploy your own mosquitto broker. I see your set up as 3 sensor groups defined by the channel used #define MY_RF24_CHANNEL ChannelOfSensorGroup Each sensor group has some number of sensors and one MQTT GW on ESP8266. On the MQTT side, do you distinguish between gateways by using a different host name? Something like: #define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway-nOf3-out" #define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway-nOf3-in" #define MY_MQTT_CLIENT_ID "mysensors-nOf3" #define MY_HOSTNAME "ESP8266_MQTT_GW_nOf3" //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 #define MY_CONTROLLER_URL_ADDRESS "test.mosquitto.org" #define MY_PORT 1883 I must assume your controller (aka Home Assistant) discriminates between through which gateway the data is to flow by way of the different topic names. If my "something like" is correct, then changing brokers is changing the IPaddress/URL in your gateways and in your controller (though if the controller is Home Assistant, it may be a bother because the device-id's may change which will make a mess of all the work you've done in HA. This is why I like @eiten 's solution.) I hope it's all working for you again. OSD
[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

3

0
Votes

3
Posts

18
Views

Thanks, I'll keep this in mind if I decide to debug it. I realized that I am also tired of patching the gateway through to the doctor container inside an LXC so now I am looking at creating an esp gateway. Just need to check if I can find a pcb on here. Thanks again!
Gateway without a radio
Development • • OldSurferDude

3

0
Votes

3
Posts

25
Views

@OldSurferDude yes, just run the configure command with --my-transport=none

RFM69 Driver

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

LAN8720A - will mysensors work with this module
Development • • Marcin

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

Gateway without a radio
Development • • OldSurferDude

59
Online

11.5k
Users

11.1k
Topics

112.7k
Posts

RFM69 Driver

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

Saving last known good state, but not in EEPROM Development • • OldSurferDude

LAN8720A - will mysensors work with this module Development • • Marcin

MQTT GW on ESP8266 supporting SSL/TLS? Development • esp8266 mqtt gw • • bgunnarb

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000' Development • • kiesel

Gateway without a radio Development • • OldSurferDude

59Online

11.5kUsers

11.1kTopics

112.7kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

LAN8720A - will mysensors work with this module
Development • • Marcin

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

Gateway without a radio
Development • • OldSurferDude

59
Online

11.5k
Users

11.1k
Topics

112.7k
Posts