💬 Door, Window and Push-button Sensor

[alowhum]

Totally true.

I was wondering what the state of Attiny85 support is. For absolute beginners (in workshops) it might be easier to connect the radio to a digispark.

// cancel that. It could never support encryption.

[Pavel Polititsky]

I have some troubles with this device.
Sometimes it does not respond to the first click, sometimes it remains switched on after first click until second click

When I press the button once - I see the LED on my gateway blinks always 3 times
1 RX TX
2 RX ERR
3 RX ERR

Device powered with CR2032 and running on 1Mhz@1.8V (internal clock)
Button input pulled to GND with resistor 47K and waking up if VCC connected through the button
Also have a 10uF tantal capacitor on power supply pins +several 0,1uF ceramic capacitors

Actually I dont know how to debug/log my gateway messages on Linux

Node code:

// Enable debug prints to serial monitor
//#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_NRF5_ESB
//#define MY_RADIO_RFM69
//#define MY_RADIO_RFM95
#define MY_RF24_PA_LEVEL RF24_PA_HIGH

#include <MySensors.h>

#define SKETCH_NAME "Door button"
#define SKETCH_MAJOR_VER "1"
#define SKETCH_MINOR_VER "0"

#define PRIMARY_CHILD_ID 3
#define PRIMARY_BUTTON_PIN 2   // Arduino Digital I/O pin for button/reed switch
//#define BATTERY_SENSE_PIN A6  // select the input pin for the battery sense point
int oldBatteryPcnt = 0;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(PRIMARY_CHILD_ID, V_TRIPPED);

void setup()
{
  // Setup the buttons
  pinMode(PRIMARY_BUTTON_PIN, INPUT);
  //	pinMode(SECONDARY_BUTTON_PIN, INPUT_PULLUP);

}

void presentation()
{
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo(SKETCH_NAME, SKETCH_MAJOR_VER "." SKETCH_MINOR_VER);
  present(PRIMARY_CHILD_ID, S_DOOR);
}

// Loop will iterate on changes on the BUTTON_PINs
void loop()
{
  uint8_t value;
  static uint8_t sentValue = 2;

  // Short delay to allow buttons to properly settle
  sleep(5);

  value = digitalRead(PRIMARY_BUTTON_PIN);

  if (value != sentValue) {
    // Value has changed from last transmission, send the updated value
    send(msg.set(value == HIGH));
    sentValue = value;
  }

  // Sleep until something happens with the sensor
  sleep(PRIMARY_BUTTON_PIN - 2, CHANGE, 0);
}

Serial data, one line = one button click

4;3;1;0;16;0
4;3;1;0;16;1
4;3;1;0;16;0
4;3;1;0;16;0
4;3;1;0;16;0
4;3;1;0;16;1
4;3;1;0;16;1
4;3;1;0;16;0
4;3;1;0;16;0
4;3;1;0;16;0
4;3;1;0;16;0
4;3;1;0;16;1
4;3;1;0;16;1
4;3;1;0;16;1
4;3;1;0;16;1
4;3;1;0;16;1
4;3;1;0;16;0
4;3;1;0;16;0
4;3;1;0;16;0
4;3;1;0;16;1
4;3;1;0;16;0
4;3;1;0;16;1

[gohan]

Uncomment the my_debug and you should see all the debug info.

[Pavel Polititsky]

@gohan I cant to set correct speed for the serial port because used 1mhz@int osc
I tried all options...

[gohan]

You can do it on the gateway at least

[Pavel Polititsky]

@gohan already done but not possible to see anything
Every line was shifted to the right side and finally no space left.
I use minicom app for monitoring serial port

,1-1-0,s=3,c=1,t=16,pt=1,l=1,sg=,1-1-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
                                                                   ,1-1-0,s=3,c=1,t=16,pt=1,l=1,sg=0;255;3;0;9;3726496 TSF:MSG:READ0:0
                                                                                                                                      1;3;1;0;16;0
                                                                                                                                                  ,1-1-0,s=3,c=1,t=16,pt=1,l=1,sg=0;255;3;0;9;3727488 TSF:MSG:READ0:0
                                                                                                                                                                                                                     1;3;1;0;16;0
                                                                                                                                                                                                                                 ,1-1-0,s=3,c=1,t=16,pt=1,l=1,sg=0;255;3;0;9;3728475 TSF:MSG:READ0:0
                                                                                                                                                                                                                                                                                                    1;3;1;0;16;0
                                                                                                                                                                                                                                                                                                                ,1-1-0,s=3,c1
                                                                                                                                                                                                                                                                                                                            1
                                                                                                                                                                                                                                                                                                                            0
                                                                                                                                                                                                                                                                                                                            0
                                                                                                                                                                                                                                                                                                                            1
                                                                                                                                                                                                                                                                                                                            1
                                                                                                                                                                                                                                                                                                                            1
                                                                                                                                                                                                                                                                                                                            1
                                                                                                                                                                                                                                                                                                                            =

Actually i need to make 100-1000 clicks to catch a fail moment
Here is working fine

[gohan]

Can't you just use the arduino ide serial monitor?

[Pavel Polititsky]

This post is deleted!

[Pavel Polititsky]

This post is deleted!

[Pavel Polititsky]

I was build a new button node with new arduino (8mhz) and new nrf24, then update to 2.3.0 gateway and all other devices
But now have a worse result than before

16 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.3.0
26 TSM:INIT
28 TSF:WUR:MS=0
34 TSM:INIT:TSP OK
36 TSF:SID:OK,ID=11
38 TSM:FPAR
75 TSF:MSG:SEND,11-11-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
403 TSF:MSG:READ,0-0-11,s=255,c=3,t=8,pt=1,l=1,sg=0:0
409 TSF:MSG:FPAR OK,ID=0,D=1
2084 TSM:FPAR:OK
2084 TSM:ID
2086 TSM:ID:OK
2088 TSM:UPL
2093 TSF:MSG:SEND,11-11-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2099 TSF:MSG:READ,0-0-11,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2105 TSF:MSG:PONG RECV,HP=1
2109 TSM:UPL:OK
2111 TSM:READY:ID=11,PAR=0,DIS=1
2129 TSF:MSG:SEND,11-11-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2138 TSF:MSG:READ,0-0-11,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2168 TSF:MSG:SEND,11-11-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.3.0
2179 TSF:MSG:SEND,11-11-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2187 TSF:MSG:READ,0-0-11,s=255,c=3,t=6,pt=0,l=1,sg=0:M
2220 TSF:MSG:SEND,11-11-0-0,s=255,c=3,t=11,pt=0,l=11,sg=0,ft=0,st=OK:Door button
2230 TSF:MSG:SEND,11-11-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.5
2240 TSF:MSG:SEND,11-11-0-0,s=3,c=0,t=0,pt=0,l=0,sg=0,ft=0,st=OK:
2246 MCO:REG:REQ
2252 TSF:MSG:SEND,11-11-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
2260 TSF:MSG:READ,0-0-11,s=255,c=3,t=27,pt=1,l=1,sg=0:1
2267 MCO:PIM:NODE REG=1
2269 MCO:BGN:STP
2271 MCO:BGN:INIT OK,TSP=1
2275 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
2279 TSF:TDI:TSL
2281 MCO:SLP:WUP=-1
2283 TSF:TRI:TSB
2287 TSF:MSG:SEND,11-11-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
2295 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
2299 TSF:TDI:TSL

the pressing button twice

30343 MCO:SLP:WUP=0
30345 TSF:TRI:TSB
30347 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
30353 TSF:TDI:TSL
30355 MCO:SLP:WUP=-1
30357 TSF:TRI:TSB
32043 !TSF:MSG:SEND,11-11-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=3,st=NACK:1
32049 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
32055 TSF:TDI:TSL
32057 MCO:SLP:WUP=0
32059 TSF:TRI:TSB
32061 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
32067 TSF:TDI:TSL
32069 MCO:SLP:WUP=-1
32071 TSF:TRI:TSB
32073 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
32079 TSF:TDI:TSL
32081 MCO:SLP:WUP=0
32083 TSF:TRI:TSB
32086 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
32092 TSF:TDI:TSL
32094 MCO:SLP:WUP=-1
32096 TSF:TRI:TSB
33779 !TSF:MSG:SEND,11-11-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=4,st=NACK:0
33787 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
33794 TSF:TDI:TSL

But no incoming messages at the gateway. Only several random messages coming to controller from one hundred button clicks
Sometimes after fast series of clicks I get this:

23179 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23183 !MCO:SLP:TNR
23185 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23191 !MCO:SLP:TNR
23218 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23222 !MCO:SLP:TNR
23224 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23230 !MCO:SLP:TNR
23257 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23261 !MCO:SLP:TNR
23263 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23269 !MCO:SLP:TNR
23296 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23300 !MCO:SLP:TNR
23302 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23308 !MCO:SLP:TNR
23336 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23341 !MCO:SLP:TNR
23343 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23349 !MCO:SLP:TNR
23377 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23382 !MCO:SLP:TNR
23384 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23390 !MCO:SLP:TNR
23418 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23422 !MCO:SLP:TNR
23425 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23431 !MCO:SLP:TNR
23459 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23463 !MCO:SLP:TNR
23465 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23472 !MCO:SLP:TNR
23500 !TSF:SND:TNR
23502 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23506 !MCO:SLP:TNR
23508 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23515 !MCO:SLP:TNR
23543 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23547 !MCO:SLP:TNR
23549 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23556 !MCO:SLP:TNR
23584 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23588 !MCO:SLP:TNR
23590 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23597 !MCO:SLP:TNR
23625 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23629 !MCO:SLP:TNR
23631 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23638 !MCO:SLP:TNR
23666 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23670 !MCO:SLP:TNR
23672 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23678 !MCO:SLP:TNR
23707 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23711 !MCO:SLP:TNR
23713 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23719 !MCO:SLP:TNR
23746 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23750 !MCO:SLP:TNR
23752 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23758 !MCO:SLP:TNR
23785 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23789 !MCO:SLP:TNR
23791 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23797 !MCO:SLP:TNR
23824 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23828 !MCO:SLP:TNR
23830 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23836 !MCO:SLP:TNR
23863 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23867 !MCO:SLP:TNR
23869 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23875 !MCO:SLP:TNR
23902 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23906 !MCO:SLP:TNR
23908 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23914 !MCO:SLP:TNR
23941 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23945 !MCO:SLP:TNR
23947 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23953 !MCO:SLP:TNR
23980 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
23984 !MCO:SLP:TNR
23986 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
23992 !MCO:SLP:TNR
24014 TSF:MSG:READ,0-0-11,s=255,c=3,t=8,pt=1,l=1,sg=0:0
24020 TSF:MSG:FPAR OK,ID=0,D=1
24025 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24029 !MCO:SLP:TNR
24031 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24037 !MCO:SLP:TNR
24064 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24068 !MCO:SLP:TNR
24070 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24076 !MCO:SLP:TNR
24104 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24109 !MCO:SLP:TNR
24111 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24117 !MCO:SLP:TNR
24145 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24150 !MCO:SLP:TNR
24152 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24158 !MCO:SLP:TNR
24186 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24190 !MCO:SLP:TNR
24193 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24199 !MCO:SLP:TNR
24227 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24231 !MCO:SLP:TNR
24233 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24240 !MCO:SLP:TNR
24268 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24272 !MCO:SLP:TNR
24274 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24281 !MCO:SLP:TNR
24309 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24313 !MCO:SLP:TNR
24315 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24322 !MCO:SLP:TNR
24350 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24354 !MCO:SLP:TNR
24356 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24363 !MCO:SLP:TNR
24391 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24395 !MCO:SLP:TNR
24397 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24403 !MCO:SLP:TNR
24432 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24436 !MCO:SLP:TNR
24438 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24444 !MCO:SLP:TNR
24471 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24475 !MCO:SLP:TNR
24477 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24483 !MCO:SLP:TNR
24510 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24514 !MCO:SLP:TNR
24516 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24522 !MCO:SLP:TNR
24549 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24553 !MCO:SLP:TNR
24555 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24561 !MCO:SLP:TNR
24588 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24592 !MCO:SLP:TNR
24594 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24600 !MCO:SLP:TNR
24627 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24631 !MCO:SLP:TNR
24633 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24639 !MCO:SLP:TNR
24666 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24670 !MCO:SLP:TNR
24672 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24678 !MCO:SLP:TNR
24705 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24709 !MCO:SLP:TNR
24711 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24717 !MCO:SLP:TNR
24745 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24750 !MCO:SLP:TNR
24752 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24758 !MCO:SLP:TNR
24786 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24791 !MCO:SLP:TNR
24793 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24799 !MCO:SLP:TNR
24827 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24832 !MCO:SLP:TNR
24834 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24840 !MCO:SLP:TNR
24868 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24872 !MCO:SLP:TNR
24875 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24881 !MCO:SLP:TNR
24909 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24913 !MCO:SLP:TNR
24915 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24922 !MCO:SLP:TNR
24950 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24954 !MCO:SLP:TNR
24956 MCO:SLP:MS=25,SMS=0,I1=255,M1=255,I2=255,M2=255
24963 !MCO:SLP:TNR
24991 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
24995 !MCO:SLP:TNR
24997 MCO:SLP:MS=25,

Then it continue works as before

Actually I have problems only with fu@ing button, most simplest device. Several month I can't to start use it.
All other devices are working properly even on 2.3.0 ver. :stuck_out_tongue_winking_eye:

[gohan]

Have you tried with a debouce? Just in case...

[Pavel Polititsky]

This post is deleted!

[Pavel Polititsky]

@gohan the default sketch with debounce library works better, but now i see my primary problem.
Occasionally I have an ACK errors

4231 TSF:MSG:SEND,21-21-0-0,s=3,c=1,t=16,pt=2,l=2,sg=0,ft=0,st=OK:0
4239 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
4245 TSF:TDI:TSL
4247 MCO:SLP:WUP=0
4249 TSF:TRI:TSB
4290 !TSF:MSG:SEND,21-21-0-0,s=3,c=1,t=16,pt=2,l=2,sg=0,ft=0,st=NACK:1
4298 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
4302 TSF:TDI:TSL
4304 MCO:SLP:WUP=0
4306 TSF:TRI:TSB
4313 TSF:MSG:SEND,21-21-0-0,s=3,c=1,t=16,pt=2,l=2,sg=0,ft=1,st=OK:0
4321 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255

I tried to icrease the time ack on my controller - it does not help
Ithink that I need to ckeck ack state on the node and send the message again, but have no idea how to do

[gohan]

you are at the limit of the radio range I'd say so randomly it looses a message, so you need to either increase power or get a better antenna (I hope you aren't using any buck/boost converter as power supply)

[Pavel Polititsky]

@gohan how you know?
Id 21 from range 0..255. Are you sure that is limit?

Same with any different IDs, I tried sending message 3 times, this guarantees delivery of payload, but it using too much power

Now I use power supply with 1117

But my other nodes powered by CR2032 with boost 0.8-3.3V dc/dc with inductor coil on the NRF24 supply pin without any troubles

[Nca78]

@pavel-polititsky said in 💬 Door, Window and Push-button Sensor:

@gohan how you know?
Id 21 from range 0..255. Are you sure that is limit?

He means radio range (distance) not ID of node ;)

[Pavel Polititsky]

@nca78 oke, undestood
Problem stiil not resolved. I want to send message again to the gateway if NACK but dont know how to do it.

send(msg.set(value == HIGH), true); 

in this case i have additional ack log in the serial debug, nothing more

[gohan]

The send function returns a value, so you can check if it was successfully sent or not and in case retry

[alowhum]

A quick ACK example:

        static boolean tryAgainLater = false; // should we resend?

        if(send(msgDust.setSensor(CHILD_ID_DUST_PM25).set(sensorValue),1)){
          Serial.println(F("Received ACK"));
          tryAgainLater = false;
        }else {
          Serial.println(F("Connection problem, try again"));
          tryAgainLater = true;
        }

[mfalkvidd]

There is no need to set the second parameter to send() to true. That parameter is unrelated to the return value (except very unfortunate similar naming). More info: https://github.com/mysensors/MySensors/issues/1103