💬 FOTA (Wireless Programming)

[scalz]

@rfm69 does your rfm69 CS signal have a pullup? If not, you should add one, because pin can be floating (so it's bad practice to not have pullup on CS lines) and interfering during AVRSPI reprogramming

[RFM69]

@scalz Thanks for the suggestion. By CS do you mean the DI00 on rmf69 and pin2 INT0 on mini pro ?

I get confused by these things, so need to confirm. :)

What type of value pullup would you suggest. Again I'm new to this.

Thanks

[scalz]

@RFM69
CS/SS of the SPI bus, for enabling/disabling device spi comm. it's your rfm69 NSS pin if you prefer.
I usually use 56k pullup resistor

[RFM69]

@scalz thanks will give it ago.

[Guillermo Schimmel]

Hi there. For what I'm reading, the MYSBootloader allways uses the default channel 76. Is that correct? It would be a very important addition to this howto.

[mfalkvidd]

@guillermo-schimmel not always, but by default. To change the channel, the bootloader must be recompiled. I have added a note to the howto. Could you check if the information is sufficiently clear?

[Guillermo Schimmel]

I recompiled MYSBootloader 1.3 with the RF Channel I use and it's now working. I can confirm that FOTA works great over MQTT gateway.

[Guillermo Schimmel]

@mfalkvidd Thank you as usual.

I can confirm that is indeed working by recompiling to my channel.

I have however a couple of questions.

1. When you say "by default", do that means that there is a way of modify that default? If so, how?

2. This specific node that I'm testing with, have a fixed node id (I use OpenHAB). But with the recompiled bootloader it "knows" which firmware download. Where does it gets from? Is the bootloader accessing the main sketch? Or is the node id info fixed in eeprom.

3. If the node id info is in eeprom, could we also have the channel there? It would be so great not having to compile the bootloader.

Thanks a lot, as allways.

[mfalkvidd]

@guillermo-schimmel

1. Yes. Isn't that exactly what you did when you did this: "I can confirm that is indeed working by recompiling to my channel" ?
2. I don't know. But I would also guess eeprom.
3. The bootloader needs to fit into a very small size, so I am not sure if there is room to read the channel from eeprom.

Maybe @scalz can comment on 2 and 3.

[Guillermo Schimmel]

@mfalkvidd said in 💬 FOTA (Wireless Programming):

@guillermo-schimmel

1. Yes. Isn't that exactly what you did when you did this: "I can confirm that is indeed working by recompiling to my channel" ?

Definitely yes. And it worked. I meant a non-compiling way, like set some eeprom variable.

2. I don't know. But I would also guess eeprom.
3. The bootloader needs to fit into a very small size, so I am not sure if there is room to read the channel from eeprom.

Maybe @scalz can comment on 2 and 3.

Please @scalz should you have a little room, this would be a very nice feature to have.

Thank you both guys.

Regards

[mfalkvidd]

I guess the main hurdle would be that while MySensors stores the node id in eeprom today, the nrf channel is not stored in eeprom. Since bootloader and sketch use the same eeprom, there would have to be some sort of agreement on where to store the channel.

[jimmy loyens]

Hello, I have my MySensors gateway permanently attached to my openhab server (RPI3), but i want to do FOTA uploads from my desktop. How do I do this since MYSController needs to attatch to a gateway? Can i use an other gateway, both with the same address (ID0)? Thanks

[sindrome73]

@mfalkvidd Hello.
From what I read it is possible to somehow modify the channel for OTA updates, this is also said here.
https://www.mysensors.org/about/fota

But I can not find other info on how to proceed to change the channel .....
Can you give me some other clarification or link to follow ???

[Guillermo Schimmel]

@sindrome73 You have to recompile the bootloader.

It's easier than it seems.

1. Mirror this repo on some machine with devel tools (I use OpenSUSE)

https://github.com/mysensors/MySensorsBootloaderRF24

2. Edit the file MYSBootloader.c, only the line:

#define RF24_CHANNEL (76) // RF channel for the sensor net, 0-127; default 76

3. Run Make

Probably it's going to need all the set of avr devel tools. Install them according to your distribution instructions.

4. You are going to get a .hex. That is the bootloader with the new channel. Install it according the standard instructions. I use AVRDUDESS.

I can confirm that I did this and it's working great.

[sindrome73]

@guillermo-schimmel Thanks for the reply.
Very useful, but can you tell me more accurately what software to use to recompile after making the change ????
Maybe some links to the software to download ..... thanks again for the availability

[Guillermo Schimmel]

@sindrome73 You have to use the Make tool, which is going to call the avr-gcc compiler.

Have you ever compiled something using command line tools?

If you don't know what I'm talking about, just tell me your channel and I can compile a bootloader for you.

[acb]

Quick question: Should FOTA work with personalized nodes/gateway?

If the answer should be yes, then I appear to have a problem…

As soon as I enable signing and signature requesting, the node will no longer respond to any internal or stream commands (e.g. Request Presentation, Reboot, Firmware, etc.) made via @tekka’s MYSController app. I haven’t tried anything else yet.

The node still happily sends signed sensor data to the gateway and they ping-pong with heartbeats, etc.

And as soon as I disable signing and signature requesting, the node will respond to all those same commands, quite happily rebooting, updating the firmware, etc.

So, am I doing something wrong?

(MYSController Version: 1.0.0beta, b3316. MySensors Library v2.3.1)

[sindrome73]

@sindrome73 Hi Good evening, and I'm sorry for the delay in the reply.
As you have never done a Bootloader, if you are kind enough to do it, I thank you.
The channel I'm using is the "Channel 84" for now I'm using only the 16MHZ Bootloade, but if you want, the others are fine too.
In addition you can give me some starting point to be able to fill in too ??
Thanks for your availability, greetings

[Guillermo Schimmel]

@sindrome73 here you have bootloaders for all the channels.

https://github.com/guillebot/MYSensors-Bootloaders

They are unchanged from default elsewhere. Only RF CHANNEL.

[sindrome73]

Hello!! And thank you again ......
A really good job, it's something that was definitely missing ......
I would suggest to the directors to expand the guide on OTA you better explain the steps to change channels and make a link to your great job !!

Now if I understand this and the Bootloader that I have to load on my Arduino Pro-Mini, in practice insert in the path of the IDE of Arduino when I make the updates use that channel

As soon as I can I try them and I'll let you know, in a lot of thanks again ......