Alarm Clock

ben999

Guys

Making progress, mainly on sketch-side of it.

Now on the hardware side of it : i would like to power the clock via a single 18650 cell (2000mah from old laptop)

So i need a regulation unit, as LiIon cell will run from 4.2V down to 2.3V (cut-off from protection board)

NRF, arduino nano and 5110 screen need 3.3V supply
NRF and arduino will draw up to 30mA when transmitting
5110 screen backlight will draw 50mA, logic seems to draw nearly nothing...
So that would be a grand total of less than 100mA

That converter would need to step-down as well as step-up depending on "petrol level" of the cell...
Does it even exist ??

@NeverDie suggested this elsewhere on the forum... http://www.ti.com/product/TPS82740B/description&lpos=Middle_Container&lid=Alternative_Devices

Or shall i simply connect the LiIon cell straight to arduino board (raw pin) and let it power the screen and radio (3.3 pin) ?? As it seems the on-board regulator can handle upto 150mA... smell of burning chips... ? :laughing:

Would it fit the bill ? Any suggestions ?

Thanks a lot !

ben999

And here is my code up-to now :

What it does on node's side

displays time, date, and alarm if set (if not, displays "alarm Off")
updates itself once a week by asking controller
list menus to :
- set alarm on or off
- set alarm time (hour and minute)
- change screen contrast

What is does on openHab

turns on and off alarm via a switch (item #1 - lock sensor)
displays time of alarm and when it has been updated (item #0 - text)

I have ordered a WTV020-SD-16P module so that my little guys can wake-up to the sound of "the Final Countdown" !
http://www.ebay.com/itm/U-disk-audio-player-TF-SD-card-voice-module-MP3-Sound-WTV020-SD-16P-Arduino/310629013078?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

And last on the list, being able to change alarm time via paperUI and iPhone app

Thanks for your comments (be gentle on arduino sketch ;) )

/*******Interrupt-based Rotary Encoder Sketch*******
by Simon Merrett, based on insight from Oleg Mazurov, Nick Gammon, rt, Steve Spence */

//#define MY_DEBUG          // Enable debug prints
#define MY_RADIO_NRF24   // Enable and select radio type attached

#define MY_PARENT_ID 0
#define MY_NODE_ID 50

#include <SPI.h>
#include <Adafruit_GFX.h>
#include <Adafruit_PCD8544.h>
#include <MySensors.h>
#include <Time.h>

#define ALARM_ID 0                      // Id of TimeOfAlarm value
#define ACTIV_ID 1                      // Id of ActivateAlarm switch

static int pinA = 2; // Our first hardware interrupt pin is digital pin 2
static int pinB = 3; // Our second hardware interrupt pin is digital pin 3
static int enSW = 4; // Rotary switch push-button

volatile byte aFlag = 0; // let's us know when we're expecting a rising edge on pinA to signal that the encoder has arrived at a detent
volatile byte bFlag = 0; // let's us know when we're expecting a rising edge on pinB to signal that the encoder has arrived at a detent (opposite direction to when aFlag is set)
volatile uint16_t encoderPos = 0; //this variable stores our current value of encoder position. Change to int or uin16_t instead of byte if you want to record a larger range than 0-255
volatile uint16_t oldEncPos = 0; //stores the last encoder position value so we can compare to the current reading and see if it has changed (so we know when to print to the serial monitor)
volatile byte reading = 0; //somewhere to store the direct values we read from our interrupt pins before checking to see if we have moved a whole detent

// Software SPI (slower updates, more flexible pin options):
// pin 7 - Serial clock out (SCLK)
// pin 6 - Serial data out (DIN)
// pin 5 - Data/Command select (D/C)
// pin 4 - LCD chip select (CS)
// pin 8 - LCD reset (RST)
Adafruit_PCD8544 display = Adafruit_PCD8544(A4, A3, A2, A1, A0);

//Declare the Menus you need.
char menu[][10] = {"Activer", "Regler", "Ecran", "Volume", "Retour"};
byte itemCount = 4;
int itemSelected;
byte runOnceAWeek = 1;   //allow for time update once a week

char dataBuffer[20];  // for sprintf function
bool alarmStatus;     // Alarm set/unset status
int alarmHour = 0;
int alarmMin = 0;
int contrast = 50;
int backlightFlag = 0;
int backlightCountdown = 10000;   // switch off backlight after XX millisec
int loopTime = 0;
int prevMillis = 0;

MyMessage  textMsg(ALARM_ID, V_TEXT);      // Initialize clock messages
MyMessage alarmMsg(ACTIV_ID, V_LOCK_STATUS);    // Initialize switch messages

void presentation()  {
  sendSketchInfo("Loulou's Clock", "08.07.2017");
  present(ALARM_ID, S_INFO);
  present(ACTIV_ID, S_LOCK);
}

void setup() {
  pinMode(A5, OUTPUT);     //5110 screen backlight
  digitalWrite(A5, LOW);
  display.begin();
  pinMode(enSW, INPUT_PULLUP);
  pinMode(pinA, INPUT_PULLUP);
  pinMode(pinB, INPUT_PULLUP);
  attachInterrupt(0, PinA, RISING);
  attachInterrupt(1, PinB, RISING);
  Serial.begin(115200);
  display.setContrast(contrast);
  display.display();
  display.clearDisplay();
  display.setTextColor(BLACK);

  int clockCounter = 0;
  while (timeStatus() == timeNotSet && clockCounter < 60) {
    requestTime();
    clockCounter++;
    wait(1000);
    /*
      Serial.print("état reception:");
      Serial.println(timeStatus());
    */
    if (clockCounter > 16) {
      /*
        Serial.print(F("**Failed Clock**"));
        Serial.print(F("*Syncronization*"));
      */
      break;
    }
  }
  alarmStatus = loadState(0);    // Read last lock status from eeprom
  setAlarmState(alarmStatus, true); // Now set the last known state and send it to controller
  sendTime();
}

void loop() {
  /*** synchronise clock node with controller from time to time... ***/
  if (weekday() == 5 && runOnceAWeek == 1) {
    requestTime();
    runOnceAWeek = 0;
  }
  if (weekday() != 5)
    runOnceAWeek = 1;

  /*** switch off backlight function ***/
  loopTime = millis() - prevMillis;
  prevMillis = millis();
  backlightFlag = backlightFlag + loopTime;
  if (backlightFlag > backlightCountdown) {
    digitalWrite(A5, HIGH);
    backlightFlag = backlightCountdown + 1;   // to avoid overflow
  }
  else
    digitalWrite(A5, LOW);

  /*** Show time on the default Screen ***/
  display.clearDisplay();
  display.setTextSize(2);
  display.setCursor(14, 2);
  sprintf(dataBuffer, "%02u:%02u ", hour() + 2, minute());
  display.print(dataBuffer);
  display.display();
  display.setTextSize(1);
  display.setCursor(14, 22);
  sprintf(dataBuffer, "%02u-%02u-%04u ", day(), month(), year());
  display.print(dataBuffer);
  display.display();

  if (alarmStatus == 0) {       //Show whether alarm is on or off
    display.setCursor(14, 35);
    sprintf(dataBuffer, "Alarme OFF");
  }
  else {
    display.setCursor(7, 35);
    char alarmText[7] = "Alarme";
    sprintf(dataBuffer, "%s %02u:%02u", alarmText, alarmHour, alarmMin);
  }
  display.print(dataBuffer);
  display.setTextSize(1);
  display.display();

  /*** Enter the settings menu if select Switch is pressed ***/
  if (digitalRead(enSW) == 0) {
    while (digitalRead(enSW) == 0); //wait till switch is released.
    encoderPos = 0;
    digitalWrite(A5, LOW);          // switch backlight ON when entering menu
    switch (encoderPos) {           //Enter main program
      case 0: display.clearDisplay();
        display.setTextSize(2);
        display.setCursor(0, 10);
        display.println(menu[encoderPos]);
        display.display();
        while (digitalRead(enSW)) {
          encoderPos = constrain(encoderPos, 0, itemCount);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.println(menu[encoderPos]);
          if (encoderPos < 0)
            encoderPos = itemCount;
          if  (encoderPos > itemCount)
            encoderPos = 0;
          display.display();
        }
        while (digitalRead(enSW) == 0);
        itemSelected = encoderPos;
      default: break;
    }
    switch (itemSelected) {
      case 0: display.clearDisplay();      //ACTIVATE ALARME
        display.setTextSize(2);
        display.setCursor(0, 10);
        display.println(menu[itemSelected]);
        display.display();
        encoderPos = alarmStatus;
        while (digitalRead(enSW)) {
          encoderPos = constrain(encoderPos, 0, 1);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.print(menu[itemSelected]);
          display.setCursor(16, 26);
          display.print(encoderPos);
          if (encoderPos == 0)  {
            sprintf(dataBuffer, "OFF");
          }
          else  {
            sprintf(dataBuffer, "ON");
          }
          display.setCursor(45, 26);
          display.print(dataBuffer);
          display.display();
        }
        if (encoderPos != alarmStatus)  {
          alarmStatus = encoderPos;
          send(alarmMsg.set(alarmStatus));
        }
        while (digitalRead(enSW) == 0);
        break;

      case 1: display.clearDisplay();     //SET ALARME TIME
        display.setTextSize(2);
        display.setCursor(0, 10);
        display.print(menu[itemSelected]);
        display.display();
        encoderPos = alarmHour;
        while (digitalRead(enSW)) {       //SET ALARME HOUR
          encoderPos = constrain(encoderPos, 00, 23);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.print(menu[itemSelected]);
          display.setCursor(10, 26);       //HOUR LOCATION
          display.print(encoderPos);
          if (encoderPos < 0)
            encoderPos = 23;
          if  (encoderPos > 23)
            encoderPos = 0;
          display.setCursor(35, 26);       // ":" LOCATION
          display.print(":");
          display.setCursor(50, 26);       //MINUTE LOCATION
          display.print(alarmMin);
          display.display();
        }
        if (encoderPos != alarmHour)  {
          alarmHour = encoderPos;
          sendTime();
        }
        encoderPos = alarmMin;
        while (digitalRead(enSW)) {        //SET ALARME MINUTE
          encoderPos = constrain(encoderPos, 00, 59);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.print(menu[itemSelected]);
          display.setCursor(10, 26);       //HOUR LOCATION
          display.print(alarmHour);
          display.setCursor(35, 26);       //":" LOCATION
          display.print(":");
          display.setCursor(50, 26);       //MINUTE LOCATION
          display.print(encoderPos);
          if (encoderPos < 0)
            encoderPos = 59;
          if  (encoderPos > 59)
            encoderPos = 0;
          display.display();
        }
        if (encoderPos != alarmMin)  {
          alarmMin = encoderPos;
          sendTime();
        }
        while (digitalRead(enSW) == 0);
        break;

      case 2: display.clearDisplay();        //CONTRAST
        display.setTextSize(2);
        display.setCursor(0, 10);
        display.print(menu[itemSelected]);
        display.display();
        encoderPos = contrast;
        while (digitalRead(enSW)) {
          encoderPos = constrain(encoderPos, 0, 100);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.print(menu[itemSelected]);
          display.setCursor(16, 16);
          display.print(encoderPos);
          if (encoderPos < 0)
            encoderPos = 100;
          if  (encoderPos > 100)
            encoderPos = 0;
          display.setContrast(encoderPos);
          display.display();
        }
        if (encoderPos != contrast)
          contrast = encoderPos;
        while (digitalRead(enSW) == 0);
        break;
      default: break;
    }
  }
}


/*** send alarm time to controller ****/
void sendTime()  {
  sprintf(dataBuffer, "%02u:%02u ", alarmHour, alarmMin);
  send(textMsg.set(dataBuffer));
  wait(1000);
}

/*** Activate alarm ***/
void setAlarmState(bool state, bool doSend) {
  if (doSend)
    send(alarmMsg.set(state));
  saveState(0, state);
  alarmStatus = state;
}

/*** receive alarme state from controller ***/
void receive(const MyMessage & message) {
  if (message.type == V_LOCK_STATUS) {
    setAlarmState(message.getBool(), false);      // Change relay state
  }
}

/*** receive a new time value ***/
void receiveTime(unsigned long controllerTime) {
  setTime(controllerTime);
}

/*** rotary encoder interrupt function ***/
void PinA() {
  cli(); //stop interrupts happening before we read pin values
  reading = PIND & 0xC; // read all eight pin values then strip away all but pinA and pinB's values
  if (reading == B00001100 && aFlag) { //check that we have both pins at detent (HIGH) and that we are expecting detent on this pin's rising edge
    encoderPos --; //decrement the encoder's position count
    bFlag = 0; //reset flags for the next turn
    aFlag = 0; //reset flags for the next turn
    backlightFlag = 0;
  }
  else if (reading == B00000100) bFlag = 1; //signal that we're expecting pinB to signal the transition to detent from free rotation
  sei(); //restart interrupts
}


void PinB() {
  cli(); //stop interrupts happening before we read pin values
  reading = PIND & 0xC; //read all eight pin values then strip away all but pinA and pinB's values
  if (reading == B00001100 && bFlag) { //check that we have both pins at detent (HIGH) and that we are expecting detent on this pin's rising edge
    encoderPos ++; //increment the encoder's position count
    bFlag = 0; //reset flags for the next turn
    aFlag = 0; //reset flags for the next turn
    backlightFlag = 0;
  }
  else if (reading == B00001000) aFlag = 1; //signal that we're expecting pinA to signal the transition to detent from free rotation
  sei(); //restart interrupts
}```

ben999

Guys

Funny discovery tonight :
"alarm time" value in PaperUI can be set by clicking on it !! It is not a read-only value, it can also BE SET !!!

0_1500492214317_Capture du 2017-07-19 21-23-03.png

Now the big question is: how can my node retreive that new value ?

21:17:04.816 [DEBUG] [rsAbstractConnection$MySensorsReader] - 50;255;3;0;21;0
21:17:20.291 [INFO ] [smarthome.event.ItemCommandEvent    ] - Item 'bedAlarm01' received command 21:12
21:17:20.296 [DEBUG] [rs.internal.gateway.MySensorsGateway] - Node 50 found in gateway
21:17:20.298 [DEBUG] [rs.internal.gateway.MySensorsGateway] - Child 0 found in node 50
21:17:20.299 [DEBUG] [rsAbstractConnection$MySensorsWriter] - Sending to MySensors: 50;0;1;0;47;21:12

Looks like gateway sends a text message (47) towards node... so sketch needs to make a difference between "lock" messages and "alarm time" messages, right ?

/*** receive alarme state and time from controller ***/
void receive(const MyMessage & message) {
  if (message.type == V_LOCK_STATUS) {
    setAlarmState(message.getBool(), false);
  }
  if (message.type == V_TEXT) {
    do (
         use strtok_r(message.data, ";", &p) to extract payload
         somehow extract hour and minute from that payload
         store them in int alarmHour int and alarmMin
  }
}

A clue to get me on the way ?

Thanks a lot for your input :)

ben999

This post is deleted!

ben999

Guys,

I need some help por favor :)

I am fighting against payload! The picture (a few posts above) shows that i can modify two values (seen under "Heure de réveil")

As i validate the new value, the gateway sends a message to the node

Sending to MySensors: 50;0;1;0;47;21:12

Which is great, that's a new feature to me :)

Now on the node side : I have included

void receive(const MyMessage & message) {
  if (message.type == V_TEXT)
    Serial.print(message.data);
   // or Serial.print(message.getString());  // works fine too
}

Serial monitor of node shows

21:12

Lovely jobly sounds good

I am now facing two major problems to me as a noob:

what is the format of "message.data" ? string? whenever i try to play with it i get some "invalid conversion" from IDE...
how to split that "message.data" into two integers (alarmHour and alarmMin) ?

Thanks for your help ! That should be the final shout for help as this project is nearly achieved...

ben999

Can someone please comment on this DIY mess (it's a mix of bits and pieces found here and there)

void receive(const MyMessage & message) {
  if (message.type == V_LOCK_STATUS)
    setAlarmState(message.getBool(), false);
  if (message.type == V_TEXT) {
    char *alarmTime =  message.data;
    char* token = strtok(alarmTime, ":");
    alarmHour = atoi(token);
    token= strtok(NULL, "");
    alarmMin = atoi(token);
  }

It works the way I need it but i guess it's a dirty way of getting there... your eyes might start bleeding :D i get this from compiler :

warning: invalid conversion from 'const char*' to 'char*' [-fpermissive]
     char *alarmTime =  message.data;

Any suggestion to make it neater?

mfalkvidd

@ben999 message.data is const char* which means its contents can not (or at least should not) be modified.
Then you set the alarmTime pointer to point to the same message.data, which means that if you modify the contents of alarmTime you will also modify the contents of message.data (they are not two copies of the same thing, they are the same thing)
The definition of strtok is

char *strtok(char *restrict source, const char *restrict delimiters);

which means the first parameter must allow modification (no const), while the second does not need modification.

The man page of strtok also says this (my emphasis):

The strtok function returns a pointer to the beginning of each subsequent token in the string, after replacing the separator character itself with a null character. When no more tokens remain, a null pointer is returned.

which explains why the parameter must allow modification.
That's why you can't do

const char *alarmTime =  message.data;

I am not a c expert, but I think you should do this instead:

void receive(const MyMessage & message) {
  if (message.type == V_LOCK_STATUS) setAlarmState(message.getBool(), false);
  if (message.type == V_TEXT) {
    char alarmTime[MAX_MESSAGE_LENGTH];
    strncpy(alarmTime, message.data, MAX_MESSAGE_LENGTH);
    char* token = strtok(alarmTime, ":");
    alarmHour = atoi(token);
    token = strtok(NULL, "");
    alarmMin = atoi(token);
  }
}

MAX_MESSAGE_LENGTH is provided by the MySensors library.

ben999

@mfalkvidd thank you very much for your detailed explanation !

It does make a lot of sense

And it compiles perfectly

Thanks again for taking the time to correct and explain :)

ben999

Full sketch
Some mods to come:

stop alarm while ringing
snoze

//#define MY_DEBUG          // Enable debug prints
#define MY_RADIO_NRF24   // Enable and select radio type attached

#define MY_PARENT_ID 0
#define MY_NODE_ID 50

#include <SPI.h>
#include <Adafruit_GFX.h>
#include <Adafruit_PCD8544.h>
#include <MySensors.h>
#include <Time.h>
#include <Wtv020sd16p.h>

#define ALARM_ID 0                      // Id of TimeOfAlarm value
#define ACTIV_ID 1                      // Id of ActivateAlarm switch

int resetPin = 5;  // The pin number of the reset pin.
int clockPin = 6;  // The pin number of the clock pin.
int dataPin = 7;  // The pin number of the data pin.
int busyPin = 8;  // The pin number of the busy pin.

static int pinA = 2; // Our first hardware interrupt pin is digital pin 2
static int pinB = 3; // Our second hardware interrupt pin is digital pin 3
static int enSW = 4; // Rotary switch push-button

volatile byte aFlag = 0; // let's us know when we're expecting a rising edge on pinA to signal that the encoder has arrived at a detent
volatile byte bFlag = 0; // let's us know when we're expecting a rising edge on pinB to signal that the encoder has arrived at a detent (opposite direction to when aFlag is set)
volatile uint16_t encoderPos = 0; //this variable stores our current value of encoder position. Change to int or uin16_t instead of byte if you want to record a larger range than 0-255
volatile uint16_t oldEncPos = 0; //stores the last encoder position value so we can compare to the current reading and see if it has changed (so we know when to print to the serial monitor)
volatile byte reading = 0; //somewhere to store the direct values we read from our interrupt pins before checking to see if we have moved a whole detent

// Software SPI (slower updates, more flexible pin options):
// pin 7 - Serial clock out (SCLK)
// pin 6 - Serial data out (DIN)
// pin 5 - Data/Command select (D/C)
// pin 4 - LCD chip select (CS)
// pin 8 - LCD reset (RST)
Adafruit_PCD8544 display = Adafruit_PCD8544(A4, A3, A2, A1, A0);


// Create an instance of the Wtv020sd16p class.
// 1st parameter: Reset pin number.
// 2nd parameter: Clock pin number.
// 3rd parameter: Data pin number.
// 4th parameter: Busy pin number.
Wtv020sd16p wtv020sd16p(resetPin, clockPin, dataPin, busyPin);

//Declare the Menus you need.
char menu[][20] = {"ActiverAlarme", "Regler Alarme" , "Contra-ste", "Volume",
                   "MusiqueAlarme", "EcouterMusique", "Retour"
                  };
byte itemCount = 6;
int itemSelected;
byte runOnceAWeek = 1;   //allow for time update once a week

char dataBuffer[20];  // for sprintf function
bool alarmStatus;     // Alarm set/unset status
int alarmHour = 0;
int alarmMin = 0;
int alarmTune = 1;
unsigned int alarmVolume = 5;
int contrast = 50;
int backlightFlag = 0;
int backlightCountdown = 10000;   // switch off backlight after XX millisec
int loopTime = 0;
int prevMillis = 0;
byte smallFont = 1;
byte bigFont = 2;

MyMessage  textMsg(ALARM_ID, V_TEXT);      // Initialize clock messages
MyMessage alarmMsg(ACTIV_ID, V_LOCK_STATUS);    // Initialize switch messages

void presentation()  {
  sendSketchInfo("Loulou's Clock", "25.07.2017");
  present(ALARM_ID, S_INFO);
  present(ACTIV_ID, S_LOCK);
}

void setup() {
  wtv020sd16p.reset();     //MP3 player
  delay(1000);
  wtv020sd16p.setVolume(alarmVolume);
  pinMode(A5, OUTPUT);     //5110 screen backlight
  digitalWrite(A5, LOW);
  display.begin();
  pinMode(enSW, INPUT_PULLUP);
  pinMode(pinA, INPUT_PULLUP);
  pinMode(pinB, INPUT_PULLUP);
  attachInterrupt(0, PinA, RISING);
  attachInterrupt(1, PinB, RISING);
  Serial.begin(115200);
  display.setContrast(contrast);
  display.display();
  display.clearDisplay();
  display.setTextColor(BLACK);

  int clockCounter = 0;
  while (timeStatus() == timeNotSet && clockCounter < 60) {
    requestTime();
    clockCounter++;
    wait(1000);
    /*
      Serial.print("état reception:");
      Serial.println(timeStatus());
    */
    if (clockCounter > 16) {
      /*
        Serial.print(F("**Failed Clock**"));
        Serial.print(F("*Syncronization*"));
      */
      break;
    }
  }
  alarmStatus = loadState(0);    // Read last lock status from eeprom
  setAlarmState(alarmStatus, true); // Now set the last known state and send it to controller
  sendTime();
}

void loop() {
  /*** ALARM !!! ***/
  while (hour() + 2 == alarmHour && minute() == alarmMin) {
    digitalWrite(A5, LOW);          // switch backlight ON when entering menu
    display.clearDisplay();
    display.setTextSize(1);
    display.setCursor(2, 2);
    display.print("Debout Axou");
    display.display();
    display.setCursor(2, 20);
    display.print("Faut y aller");
    display.display();
    display.setCursor(2, 40);
    sprintf(dataBuffer, "Il est %02u:%02u ", hour() + 2, minute());
    display.print(dataBuffer);
    display.display();
    wtv020sd16p.playVoice(alarmTune - 1);
  }

  /*** synchronise clock node with controller from time to time... ***/
  if (weekday() == 5 && runOnceAWeek == 1) {
    requestTime();
    runOnceAWeek = 0;
  }
  if (weekday() != 5)
    runOnceAWeek = 1;

  /*** switch off backlight function ***/
  loopTime = millis() - prevMillis;
  prevMillis = millis();
  backlightFlag = backlightFlag + loopTime;
  if (backlightFlag > backlightCountdown) {
    digitalWrite(A5, HIGH);
    backlightFlag = backlightCountdown + 1;   // to avoid overflow
  }
  else
    digitalWrite(A5, LOW);

  /*** Show time on the default Screen ***/
  display.clearDisplay();
  display.setTextSize(2);
  display.setCursor(14, 2);
  sprintf(dataBuffer, "%02u:%02u ", hour() + 2, minute());
  display.print(dataBuffer);
  //display.display();
  display.setTextSize(1);
  display.setCursor(14, 22);
  sprintf(dataBuffer, "%02u-%02u-%04u ", day(), month(), year());
  display.print(dataBuffer);
  display.display();

  if (alarmStatus == 0) {       //Show whether alarm is on or off
    display.setCursor(14, 35);
    sprintf(dataBuffer, "Alarme OFF");
  }
  else {
    display.setCursor(7, 35);
    char alarmText[7] = "Alarme";
    sprintf(dataBuffer, "%s %02u:%02u", alarmText, alarmHour, alarmMin);
  }
  display.print(dataBuffer);
  display.display();

  /*** Enter the settings menu if select Switch is pressed ***/
  if (digitalRead(enSW) == 0) {
    while (digitalRead(enSW) == 0); //wait till switch is released.
    encoderPos = 0;
    digitalWrite(A5, LOW);          // switch backlight ON when entering menu
    switch (encoderPos) {           //Enter main program
      case 0: display.clearDisplay();
        display.setTextSize(2);
        display.setCursor(0, 10);
        display.println(menu[encoderPos]);
        display.display();
        while (digitalRead(enSW)) {
          encoderPos = constrain(encoderPos, 0, itemCount);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.println(menu[encoderPos]);
          if (encoderPos < 0)
            encoderPos = itemCount;
          if  (encoderPos > itemCount)
            encoderPos = 0;
          display.display();
        }
        while (digitalRead(enSW) == 0);
        itemSelected = encoderPos;
      default: break;
    }
    switch (itemSelected) {
      case 0: display.clearDisplay();      //ACTIVATE ALARME
        display.setTextSize(bigFont);
        display.setCursor(0, 10);
        display.println(menu[itemSelected]);
        display.display();
        encoderPos = alarmStatus;
        while (digitalRead(enSW)) {
          encoderPos = constrain(encoderPos, 0, 1);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.print(menu[itemSelected]);
          display.setCursor(16, 34);
          display.print(encoderPos);
          if (encoderPos == 0)  {
            sprintf(dataBuffer, "OFF");
          }
          else  {
            sprintf(dataBuffer, "ON");
          }
          display.setCursor(45, 34);
          display.print(dataBuffer);
          display.display();
        }
        if (encoderPos != alarmStatus)  {
          alarmStatus = encoderPos;
          send(alarmMsg.set(alarmStatus));
        }
        while (digitalRead(enSW) == 0);
        break;

      case 1: display.clearDisplay();     //SET ALARME TIME
        display.setTextSize(bigFont);
        display.setCursor(0, 10);
        display.print(menu[itemSelected]);
        display.display();
        encoderPos = alarmHour;
        while (digitalRead(enSW)) {       //SET ALARME HOUR
          encoderPos = constrain(encoderPos, 00, 23);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.print(menu[itemSelected]);
          display.setCursor(10, 34);       //HOUR LOCATION
          display.print(encoderPos);
          if (encoderPos < 0)
            encoderPos = 23;
          if  (encoderPos > 23)
            encoderPos = 0;
          display.setCursor(35, 34);       // ":" LOCATION
          display.print(":");
          display.setCursor(50, 34);       //MINUTE LOCATION
          display.print(alarmMin);
          display.display();
        }
        if (encoderPos != alarmHour)  {
          alarmHour = encoderPos;
          sendTime();
        }
        encoderPos = alarmMin;
        while (digitalRead(enSW)) {        //SET ALARME MINUTE
          encoderPos = constrain(encoderPos, 00, 59);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.print(menu[itemSelected]);
          display.setCursor(10, 34);       //HOUR LOCATION
          display.print(alarmHour);
          display.setCursor(35, 34);       //":" LOCATION
          display.print(":");
          display.setCursor(50, 34);       //MINUTE LOCATION
          display.print(encoderPos);
          if (encoderPos < 0)
            encoderPos = 59;
          if  (encoderPos > 59)
            encoderPos = 0;
          display.display();
        }
        if (encoderPos != alarmMin)  {
          alarmMin = encoderPos;
          sendTime();
        }
        while (digitalRead(enSW) == 0);
        break;

      case 2: display.clearDisplay();        //CONTRAST
        display.setTextSize(bigFont);
        display.setCursor(0, 10);
        display.print(menu[itemSelected]);
        display.display();
        encoderPos = contrast;
        while (digitalRead(enSW)) {
          encoderPos = constrain(encoderPos, 0, 100);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.print(menu[itemSelected]);
          display.setCursor(16, 16);
          display.print(encoderPos);
          if (encoderPos < 0)
            encoderPos = 100;
          if  (encoderPos > 100)
            encoderPos = 0;
          display.setContrast(encoderPos);
          display.display();
        }
        if (encoderPos != contrast)
          contrast = encoderPos;
        while (digitalRead(enSW) == 0);
        break;

      case 3: display.clearDisplay();        //VOLUME
        display.setTextSize(smallFont);
        display.setCursor(0, 10);
        display.print(menu[itemSelected]);
        display.display();
        encoderPos = alarmVolume;
        while (digitalRead(enSW)) {
          encoderPos = constrain(encoderPos, 0, 7);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.print(menu[itemSelected]);
          display.setCursor(16, 34);
          display.print(encoderPos);
          if (encoderPos < 0)
            encoderPos = 7;
          if  (encoderPos > 7)
            encoderPos = 0;
          display.display();
          wtv020sd16p.setVolume(encoderPos);
        }
        alarmVolume = encoderPos;
        while (digitalRead(enSW) == 0);
        break;

      case 4: display.clearDisplay();        //ALARM TUNE
        display.setTextSize(bigFont);
        display.setCursor(0, 10);
        display.print(menu[itemSelected]);
        display.display();
        encoderPos = alarmTune;
        while (digitalRead(enSW)) {
          encoderPos = constrain(encoderPos, 1, 10);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.print(menu[itemSelected]);
          display.setCursor(16, 34);
          display.print(encoderPos);
          if (encoderPos < 1)
            encoderPos = 10;
          if  (encoderPos > 10)
            encoderPos = 0;
          display.display();
        }
        alarmTune = encoderPos;
        while (digitalRead(enSW) == 0);
        break;

      case 5: display.clearDisplay();        //PLAYER
        display.setTextSize(bigFont);
        display.setCursor(0, 10);
        display.print(menu[itemSelected]);
        display.display();
        encoderPos = 0;
        while (digitalRead(enSW)) {
          encoderPos = constrain(encoderPos, 0, 10);
          display.clearDisplay();
          display.setCursor(0, 0);
          display.print(menu[itemSelected]);
          display.setCursor(16, 34);
          display.print(encoderPos);
          if (encoderPos < 0)
            encoderPos = 10;
          if  (encoderPos > 10)
            encoderPos = 0;
          display.display();
        }
        if (encoderPos == 0)
          wtv020sd16p.stopVoice();
        else
          wtv020sd16p.playVoice(encoderPos - 1);
        while (digitalRead(enSW) == 0);
        break;

      default: break;
    }
  }
}

/*** receive a new time value ***/
void receiveTime(unsigned long controllerTime) {
  setTime(controllerTime);
}

/*** send alarm time to controller ****/
void sendTime()  {
  sprintf(dataBuffer, "%02u:%02u ", alarmHour, alarmMin);
  send(textMsg.set(dataBuffer));
  wait(1000);
}

/*** Activate alarm ***/
void setAlarmState(bool state, bool doSend) {
  if (doSend)
    send(alarmMsg.set(state));
  saveState(0, state);
  alarmStatus = state;
}

/*** receive alarme state from controller ***/
void receive(const MyMessage & message) {
  if (message.type == V_LOCK_STATUS)
    setAlarmState(message.getBool(), false);
  if (message.type == V_TEXT) {
    char alarmTime[MAX_MESSAGE_LENGTH];
    strncpy(alarmTime, message.data, MAX_MESSAGE_LENGTH);
    char* token = strtok(alarmTime, ":");
    alarmHour = atoi(token);
    token = strtok(NULL, "");
    alarmMin = atoi(token);
  }

}

/*** rotary encoder interrupt function ***/
void PinA() {
  cli(); //stop interrupts happening before we read pin values
  reading = PIND & 0xC; // read all eight pin values then strip away all but pinA and pinB's values
  if (reading == B00001100 && aFlag) { //check that we have both pins at detent (HIGH) and that we are expecting detent on this pin's rising edge
    encoderPos --; //decrement the encoder's position count
    bFlag = 0; //reset flags for the next turn
    aFlag = 0; //reset flags for the next turn
    backlightFlag = 0;
  }
  else if (reading == B00000100) bFlag = 1; //signal that we're expecting pinB to signal the transition to detent from free rotation
  sei(); //restart interrupts
}


void PinB() {
  cli(); //stop interrupts happening before we read pin values
  reading = PIND & 0xC; //read all eight pin values then strip away all but pinA and pinB's values
  if (reading == B00001100 && bFlag) { //check that we have both pins at detent (HIGH) and that we are expecting detent on this pin's rising edge
    encoderPos ++; //increment the encoder's position count
    bFlag = 0; //reset flags for the next turn
    aFlag = 0; //reset flags for the next turn
    backlightFlag = 0;
  }
  else if (reading == B00001000) aFlag = 1; //signal that we're expecting pinA to signal the transition to detent from free rotation
  sei(); //restart interrupts
}```

Newzwaver

Nice project would love to see the finished product as I want to try it as well. Can you post all the details once you get it do Easy?

Thanks and good luck

Newzwaver

Hi I need your help, I created this clock and complied the sketch, looked like it worked but when adding it to very I get the error message that D_LcdText1.xml is not available. Where do I find that and how do i add it to the Vera Plus?

Excellent project and can't wait to have it up and running.

korttoma

@Newzwaver you can find the needed files here

Alarm Clock

20

11.7k

11.2k

113.1k