Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Where do i get the my-board.json and other related script files to add a MYSBootloader board in Platformio

vikasjee last edited by

There are specific script files required by Platformio to add a new custom board like a MYSBootloader one. Can someone help me?
Reply Quote 0
1 Reply Last reply
martinhjelmare Plugin Developer last edited by

This is how I did it for the Sensebender Micro:
https://forum.mysensors.org/topic/2725/sensebender-micro/29
Reply Quote 1
1 Reply Last reply

2
Posts

971
Views

Log in to reply

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50411
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
Arduino Nano Every problem
Hardware • • hakha4

6

1
Votes

6
Posts

84
Views

I bought the Every because it implied it was backward compatible with the nano. No, it's not, as we found out. Be that as it may, any word on a getting the Every working with mySensors?
Sensor to detect marijuana vape/smoke
Hardware • • Hellmark

3

0
Votes

3
Posts

15
Views

@Hellmark I have a sensor with a dust sensor, and it detects sigarette smoke pretty well. I use it in my RV and act on the fairing vents.
Sleep mode for bmp280
Hardware • • fishermans

7

4
Votes

7
Posts

3282
Views

Just wanted to say thanks for this, it is still relevant and useful six years later !
Which one should i choose? PIR or microwave sensor
Hardware • • h01

8

0
Votes

8
Posts

73
Views

Supposedly PIR doesn't work through glass (e.g. if looking for motion through a window), whereas I presume a microwave sensor might still work.
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

2

0
Votes

2
Posts

21
Views

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }

53
Online

11.5k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1