Gateway update?



  • Hi,

    Here's my debug from Ethernet (Arduino Uno + shield) gateway:

    0;255;3;0;9;Starting gateway (RNNGA-, 2.0.0)
    0;255;3;0;9;TSM:INIT
    0;255;3;0;9;TSM:RADIO:OK
    0;255;3;0;9;TSM:GW MODE
    0;255;3;0;9;TSM:READY
    IP: 10.0.0.104
    0;255;3;0;9;No registration required
    0;255;3;0;9;Init complete, id=0, parent=0, distance=0, registration=1
    0;255;3;0;9;TSP:MSG:READ 21-21-0 s=1,c=1,t=0,pt=7,l=5,sg=0:26.0
    0;255;3;0;9;TSP:MSG:READ 21-21-0 s=1,c=1,t=0,pt=7,l=5,sg=0:25.9
    0;255;3;0;9;TSP:MSG:READ 8-8-0 s=0,c=1,t=37,pt=7,l=5,sg=0:50.87
    0;255;3;0;9;TSP:MSG:READ 8-8-0 s=2,c=1,t=0,pt=7,l=5,sg=0:22.0
    0;255;3;0;9;TSP:MSG:READ 8-8-0 s=0,c=1,t=37,pt=7,l=5,sg=0:61.50
    0;255;3;0;9;TSP:MSG:READ 8-8-0 s=2,c=1,t=0,pt=7,l=5,sg=0:21.9
    0;255;3;0;9;TSP:MSG:READ 8-8-0 s=1,c=1,t=1,pt=7,l=5,sg=0:40.7
    0;255;3;0;9;TSP:MSG:READ 8-8-0 s=0,c=1,t=37,pt=7,l=5,sg=0:51.34
    0;255;3;0;9;TSP:MSG:READ 21-21-0 s=1,c=1,t=0,pt=7,l=5,sg=0:26.0
    0;255;3;0;9;TSP:MSG:READ 3-3-0 s=13,c=1,t=0,pt=7,l=5,sg=0:27.7
    0;255;3;0;9;TSP:MSG:READ 21-21-0 s=1,c=1,t=0,pt=7,l=5,sg=0:25.9
    0;255;3;0;9;TSP:MSG:READ 8-8-0 s=0,c=1,t=37,pt=7,l=5,sg=0:37.04
    0;255;3;0;9;TSP:MSG:READ 21-21-0 s=1,c=1,t=0,pt=7,l=5,sg=0:26.0
    0;255;3;0;9;TSP:MSG:READ 21-21-0 s=1,c=1,t=0,pt=7,l=5,sg=0:25.9
    0;255;3;0;9;TSP:MSG:READ 21-21-0 s=1,c=1,t=0,pt=7,l=5,sg=0:26.0
    0;255;3;0;9;TSP:MSG:READ 8-8-0 s=2,c=1,t=0,pt=7,l=5,sg=0:22.0
    
    

    My nodes are sending data.

    Want to add new node and here's the problem:

    0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.0
    3 TSM:INIT
    6 TSF:WUR:MS=0
    13 !TSM:INIT:TSP FAIL
    15 TSM:FAIL:CNT=1
    16 TSM:FAIL:PDT
    10019 TSM:FAIL:RE-INIT
    10021 TSM:INIT
    10028 !TSM:INIT:TSP FAIL
    10031 TSM:FAIL:CNT=2
    10032 TSM:FAIL:PDT
    20035 TSM:FAIL:RE-INIT
    20037 TSM:INIT
    20043 !TSM:INIT:TSP FAIL
    

    It seems that I have newer version on node (2.1.0) than gateway (2.0.0).

    How to fix that?
    Should I update gateway - how?
    If yes, should I update also all remaning nodes - how?


  • Mod

    @1kohm to update the nodes, re-upload the original sketch to the nodes.

    Mixing nodes within the same major version (2.x can coexist) should be OK , so you don't need to update everything.

    TSM:INIT:TSP FAIL means that the Arduino is unable to communicate with its radio. Double-check the wiring and if the wiring is correct, try another radio module to determine if the current module is broken.



  • Hi,

    radio was the issue (placed oposite.., by bad)

    Now, I've uploaded node ver.2.0.0.

    Starting sensor (RNNNA-, 2.0.0)
    TSM:INIT
    TSM:RADIO:OK
    TSP:ASSIGNID:OK (ID=4)
    TSM:FPAR
    TSP:MSG:SEND 4-4-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
    TSP:MSG:READ 0-0-4 s=255,c=3,t=8,pt=1,l=1,sg=0:0
    TSP:MSG:FPAR RES (ID=0, dist=0)
    TSP:MSG:PAR OK (ID=0, dist=1)
    TSM:FPAR:OK
    TSM:ID
    TSM:CHKID:OK (ID=4)
    TSM:UPL
    TSP:PING:SEND (dest=0)
    TSP:MSG:SEND 4-4-0-0 s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=ok:1
    TSP:MSG:READ 0-0-4 s=255,c=3,t=25,pt=1,l=1,sg=0:1
    TSP:MSG:PONG RECV (hops=1)
    TSP:CHKUPL:OK
    TSM:UPL:OK
    TSM:READY
    TSP:MSG:SEND 4-4-0-0 s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=ok:0100
    TSP:MSG:SEND 4-4-0-0 s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=ok:2.0.0
    TSP:MSG:SEND 4-4-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=ok:0
    TSP:MSG:READ 0-0-4 s=255,c=3,t=15,pt=6,l=2,sg=0:0100
    TSP:MSG:READ 0-0-4 s=255,c=3,t=6,pt=0,l=1,sg=0:M
    TSP:MSG:SEND 4-4-0-0 s=255,c=3,t=11,pt=0,l=25,sg=0,ft=0,st=ok:Double Relay & Button tes
    TSP:MSG:SEND 4-4-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=ok:0.3
    TSP:MSG:SEND 4-4-0-0 s=8,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=ok:
    TSP:MSG:SEND 4-4-0-0 s=9,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=ok:
    Request registration...
    TSP:MSG:SEND 4-4-0-0 s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=ok:2
    TSP:MSG:READ 0-0-4 s=255,c=3,t=27,pt=1,l=1,sg=0:1
    Node registration=1
    Init complete, id=4, parent=0, distance=1, registration=1
    

    Debug looks perfect..., but cannot see the node in Domoticz i Devices tab 😞
    I can see the node under Hardware -> MySensorsGateway only:

    0_1502223123731_Przechwytywanie.PNG

    0_1502223136080_Przechwytywanie2.PNG

    I want to test gas meter IN-Z61.


  • Mod

    @1kohm great work.

    For some reason, Domoticz does not show the sensor in the devices list until the sensor has sent its first value. (presentation is not enough, a message needs to be sent). Could that be the case for you?



  • Hi,

    so my node is sending data every 3 seconds

    TSP:MSG:SEND 7-7-0-0 s=1,c=1,t=24,pt=5,l=4,sg=0,ft=0,st=ok:2
    volume:0.002
    TSP:MSG:SEND 7-7-0-0 s=1,c=1,t=35,pt=7,l=5,sg=0,ft=0,st=ok:0.002
    

    0_1502225440975_Przechwytywanie.PNG

    Domoticz see the updated vaule, but not in Devices 😞



  • Want to present the device as S_GAS

    void presentation()
    {
        // Send the sketch version information to the gateway and Controller
        sendSketchInfo("Gas Meter", "1.1");
    
        // Register this device as Waterflow sensor
        present(CHILD_ID, S_GAS);
    }
    

    Sketch I use:

    /**
     * The MySensors Arduino library handles the wireless radio link and protocol
     * between your home built sensors/actuators and HA controller of choice.
     * The sensors forms a self healing radio network with optional repeaters. Each
     * repeater and gateway builds a routing tables in EEPROM which keeps track of the
     * network topology allowing messages to be routed to nodes.
     *
     * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
     * Copyright (C) 2013-2015 Sensnology AB
     * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
     *
     * Documentation: http://www.mysensors.org
     * Support Forum: http://forum.mysensors.org
     *
     * This program is free software; you can redistribute it and/or
     * modify it under the terms of the GNU General Public License
     * version 2 as published by the Free Software Foundation.
     *
     *******************************
     *
     * REVISION HISTORY
     * Version 1.0 - Henrik Ekblad
     * Version 1.1 - GizMoCuz
     *
     * DESCRIPTION
     * Use this sensor to measure volume and flow of your house watermeter.
     * You need to set the correct pulsefactor of your meter (pulses per m3).
     * The sensor starts by fetching current volume reading from gateway (VAR 1).
     * Reports both volume and flow back to gateway.
     *
     * Unfortunately millis() won't increment when the Arduino is in
     * sleepmode. So we cannot make this sensor sleep if we also want
     * to calculate/report flow.
     * http://www.mysensors.org/build/pulse_water
     */
    
    // Enable debug prints to serial monitor
    #define MY_DEBUG
    
    // Enable and select radio type attached
    #define MY_RADIO_NRF24
    //#define MY_RADIO_NRF5_ESB
    //#define MY_RADIO_RFM69
    //#define MY_RADIO_RFM95
    
    #include <MySensors.h>
    
    #define DIGITAL_INPUT_SENSOR 7                  // The digital input you attached your sensor.  (Only 2 and 3 generates interrupt!)
    
    #define PULSE_FACTOR 1000                       // Nummber of blinks per m3 of your meter (One rotation/liter)
    
    #define SLEEP_MODE false                        // flowvalue can only be reported when sleep mode is false.
    
    #define MAX_FLOW 40                             // Max flow (l/min) value to report. This filters outliers.
    
    #define CHILD_ID 1                              // Id of the sensor child
    
    unsigned long SEND_FREQUENCY =
        3000;           // Minimum time between send (in milliseconds). We don't want to spam the gateway.
    
    MyMessage flowMsg(CHILD_ID,V_FLOW);
    MyMessage volumeMsg(CHILD_ID,V_VOLUME);
    MyMessage lastCounterMsg(CHILD_ID,V_VAR1);
    
    double ppl = ((double)PULSE_FACTOR)/1000;        // Pulses per liter
    
    volatile unsigned long pulseCount = 0;
    volatile unsigned long lastBlink = 0;
    volatile double flow = 0;
    bool pcReceived = false;
    unsigned long oldPulseCount = 0;
    unsigned long newBlink = 0;
    double oldflow = 0;
    double volume =0;
    double oldvolume =0;
    unsigned long lastSend =0;
    unsigned long lastPulse =0;
    
    void setup()
    {
        // initialize our digital pins internal pullup resistor so one pulse switches from high to low (less distortion)
        pinMode(DIGITAL_INPUT_SENSOR, INPUT_PULLUP);
    
        pulseCount = oldPulseCount = 0;
    
        // Fetch last known pulse count value from gw
        request(CHILD_ID, V_VAR1);
    
        lastSend = lastPulse = millis();
    
        attachInterrupt(digitalPinToInterrupt(DIGITAL_INPUT_SENSOR), onPulse, FALLING);
    }
    
    void presentation()
    {
        // Send the sketch version information to the gateway and Controller
        sendSketchInfo("Gas Meter", "1.1");
    
        // Register this device as Waterflow sensor
        present(CHILD_ID, S_GAS);
    }
    
    void loop()
    {
        unsigned long currentTime = millis();
    
        // Only send values at a maximum frequency or woken up from sleep
        if (SLEEP_MODE || (currentTime - lastSend > SEND_FREQUENCY)) {
            lastSend=currentTime;
    
            if (!pcReceived) {
                //Last Pulsecount not yet received from controller, request it again
                request(CHILD_ID, V_VAR1);
                return;
            }
    
            if (!SLEEP_MODE && flow != oldflow) {
                oldflow = flow;
    
                Serial.print("l/min:");
                Serial.println(flow);
    
                // Check that we dont get unresonable large flow value.
                // could hapen when long wraps or false interrupt triggered
                if (flow<((unsigned long)MAX_FLOW)) {
                    send(flowMsg.set(flow, 2));                   // Send flow value to gw
                }
            }
    
            // No Pulse count received in 2min
            if(currentTime - lastPulse > 120000) {
                flow = 0;
            }
    
            // Pulse count has changed
            if ((pulseCount != oldPulseCount)||(!SLEEP_MODE)) {
                oldPulseCount = pulseCount;
    
                Serial.print("pulsecount:");
                Serial.println(pulseCount);
    
                send(lastCounterMsg.set(pulseCount));                  // Send  pulsecount value to gw in VAR1
    
                double volume = ((double)pulseCount/((double)PULSE_FACTOR));
                if ((volume != oldvolume)||(!SLEEP_MODE)) {
                    oldvolume = volume;
    
                    Serial.print("volume:");
                    Serial.println(volume, 3);
    
                    send(volumeMsg.set(volume, 3));               // Send volume value to gw
                }
            }
        }
        if (SLEEP_MODE) {
            sleep(SEND_FREQUENCY);
        }
    }
    
    void receive(const MyMessage &message)
    {
        if (message.type==V_VAR1) {
            unsigned long gwPulseCount=message.getULong();
            pulseCount += gwPulseCount;
            flow=oldflow=0;
            Serial.print("Received last pulse count from gw:");
            Serial.println(pulseCount);
            pcReceived = true;
        }
    }
    
    void onPulse()
    {
        if (!SLEEP_MODE) {
            unsigned long newBlink = micros();
            unsigned long interval = newBlink-lastBlink;
    
            if (interval!=0) {
                lastPulse = millis();
                if (interval<500000L) {
                    // Sometimes we get interrupt on RISING,  500000 = 0.5sek debounce ( max 120 l/min)
                    return;
                }
                flow = (60000000.0 /interval) / ppl;
            }
            lastBlink = newBlink;
        }
        pulseCount++;
    }
    


  • topic to close.
    I've neede to allow new hardware to add in Domoticz.


 

347
Online

7.5k
Users

8.4k
Topics

90.4k
Posts