Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Please help me dooya remote

かいと last edited by

Re: Controlling Blinds.com RF Dooya Motors with Arduino and Vera

Please help me,
My remote is dooya. And sniff code:
10000011 01000010 01001001 11100001 00110011 pause
10000011 01000010 01001001 11100001 01010101 up
10000011 01000010 01001001 11100001 00111100 down

I had use USB Saleae Analyzer sniff code.

But not work,
Reply Quote 0
1 Reply Last reply

1
Posts

679
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Interface-board-for-remote-control
My Project • • OldSurferDude

2

1
Votes

2
Posts

21
Views

That is a well documented project. Much appreciated
BMP280 SPI Adafruit
My Project • • Matt

3

1
Votes

3
Posts

2128
Views

Hallo! Ich habe gerade meinen Aduino Nano mit einem GY-BME/P-280 verbunden über SPI verbunden. Im Sketch habe ich nur die PINS geändert und zwar auf: #define BMP_SCK 13 #define BMP_MISO 12 #define BMP_MOSI 11 #define BMP_CS 10 Ich bekomme aber bei der Ausgabe am seriellen Monitor nur "Hyroglyphen" zB 5��,�lh��}��'�O8��m�h,� Mit einem anderen Sketch funktioniert der Sensor einwandfrei. Auch mit einem anderen Nano dasselbe Ergebnis. Hat jemand eine Idee was das Problem sein könnte? Zusatzfrage da ich in C++ nicht so firm bin: Könnte es sein, dass MY_DEBUG oder MY_RADIO_NRF24 das problem verursacht. Was machen diese Definitionen eigentlich? Grüße
Nb of possible nodes in a mysensors networks with domoticz
My Project • • GLAB

18

0
Votes

18
Posts

133
Views

@OldSurferDude yeah, 10 virgin nodes powered up at the same time is a bad idea I seem to remember reading somwewhere here warning aginst that. If yu have node ID trust issues with Mysensors you should move your address to different locaion as 0x00 is used by Mysensors... just sayin..;)
Door chime
My Project • • Paul Scarbro

2

0
Votes

2
Posts

23
Views

@Paul-Scarbro There are multitude of solution, but since we are in MySensors Land, let's do a MySensors solution. You'll quickly see that doing that adds a lot of overhead. We'll use an Arduino Nano or RF Nano if you're going to go whole hog. It can be run from 3.3V or 5V DC, not AC. The reed switch would be connected to an input of the Nano and one of the outputs would drive a relay. The relay would drive the chime. Your C++ program would be something like: #define inputButton 2; // connect reed switch here #define outputRelay 4; // connect relay to this pin see MySensors Relay example #define RELAY_ON 1 // GPIO value to write to turn on attached relay #define RELAY_OFF 0 // GPIO value to write to turn off attached relay void setup() { pinmode(inputButton,INPUT); pinmode(outputRelay,OUTPUT); // put your setup code here, to run once: } void loop() { // put your main code here, to run repeatedly: if (digitalRead(inputButton) == 0) { digitalWrite(outputRelay,RELAY_ON); wait(2000); // wait 2 seconds digitalWrite(outputRelay,RELAY_OFF); // now wait for door to close while(digitalRead(inputButton) == 0) ; //does nothing until reed switch opens } } There are some subtleties that I may have glossed over, but this is the gist. By looking at the MySensors Relay example, you'll see how to integrate this into a MySensors environment. That's where you'd want to get the RF Nano. I've made the assumption you're familiar with the Arduino IDE and you've looked into the MySensors environment.
Status of my rv(camper) home automation system 2020-2025
My Project • • fsgraz

11

2
Votes

11
Posts

20
Views

@fsgraz Did some testing Today and my RFM range is over 80 meters node to node, with no long range antenna. That will be my next test, just waiting for a shipment from China to arrive. I did how ever notice an extreme improvement when I connected the gateway through a USB hub and then started to dig through the forum. @AWI once wrote about using an external PSU to power the long range NRF PA/LAN. I'll try that this weekend as connecting it to they USB port of my PI extended the range to 20 meters Node to Node.

Please help me dooya remote

Suggested Topics

Welcome
Announcements • • hek

Interface-board-for-remote-control
My Project • • OldSurferDude

BMP280 SPI Adafruit
My Project • • Matt

Nb of possible nodes in a mysensors networks with domoticz
My Project • • GLAB

Door chime
My Project • • Paul Scarbro

Status of my rv(camper) home automation system 2020-2025
My Project • • fsgraz

5
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Please help me dooya remote

Suggested Topics

Welcome Announcements • • hek

Interface-board-for-remote-control My Project • • OldSurferDude

BMP280 SPI Adafruit My Project • • Matt

Nb of possible nodes in a mysensors networks with domoticz My Project • • GLAB

Door chime My Project • • Paul Scarbro

Status of my rv(camper) home automation system 2020-2025 My Project • • fsgraz

5Online

11.5kUsers

11.1kTopics

112.8kPosts

Welcome
Announcements • • hek

Interface-board-for-remote-control
My Project • • OldSurferDude

BMP280 SPI Adafruit
My Project • • Matt

Nb of possible nodes in a mysensors networks with domoticz
My Project • • GLAB

Door chime
My Project • • Paul Scarbro

Status of my rv(camper) home automation system 2020-2025
My Project • • fsgraz

5
Online

11.5k
Users

11.1k
Topics

112.8k
Posts