Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

New version of this smoke detector sketch available?

chorob last edited by chorob

Re: 'MySensoring' a Kidde Smoke Detector. (Completed)

Hello,

This is exactly a project I need to complete. Does anyone have an updated version of this sketch that works with the newer versions of the MySensors library?

Thanks!
Reply Quote 0
1 Reply Last reply

1
Posts

655
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

1

0
Votes

1
Posts

12
Views

No one has replied
Halloween Lights
My Project • led strip light ws2812b • • KevinT

1

3
Votes

1
Posts

24
Views

No one has replied
Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home
My Project • • fsgraz

1

2
Votes

1
Posts

22
Views

No one has replied
Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

1

2
Votes

1
Posts

10
Views

No one has replied
HVAC Controller
My Project • • Michael Link

3

1
Votes

3
Posts

28
Views

We are of like minds, Don't like the cloud based controls (that's another discussion). In my case I have a Bryant/Connex system, heat pump, variable speed fan and 4 zones. There's a lot going on: the 4 zones creates 16 profiles. The fan speed for a profile will depend on the indoor and outdoor temperature. The thermal fluid pump also has to be controlled. A profile will have an optimal air pressure, so there's a sensor there. The controller works just fine not being connected to the cloud. But I want to set the parameters remotely, Bryant/Connex can do this. I also wnat the status of the various actuators and sensors to show up in Home Assistant. The signals sent over the RS422 are proprietary. My plan was to reverse-engineer the signals. After doing this I'll have to experiment to get the right mix of air pressue, fan speed and thermal fluid flow for each profile. I'd like to do the same for my AO Smith heat pump water heater. I'd like to follow your progress. OSD

New version of this smoke detector sketch available?

Suggested Topics

Welcome
Announcements • • hek

Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

Halloween Lights
My Project • led strip light ws2812b • • KevinT

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home
My Project • • fsgraz

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

HVAC Controller
My Project • • Michael Link

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

New version of this smoke detector sketch available?

Suggested Topics

Welcome Announcements • • hek

Water Meter or "How to get Home Assistant to send saved data to an Arduino" My Project • • OldSurferDude

Halloween Lights My Project • led strip light ws2812b • • KevinT

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home My Project • • fsgraz

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway My Project • • fsgraz

HVAC Controller My Project • • Michael Link

0Online

11.4kUsers

11.1kTopics

112.7kPosts

Welcome
Announcements • • hek

Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

Halloween Lights
My Project • led strip light ws2812b • • KevinT

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home
My Project • • fsgraz

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

HVAC Controller
My Project • • Michael Link

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts