Connecting Gateway to Domoticz

[ceech]

@NeverDie I have no idea.

[ceech]

@mfalkvidd It's a good advice, unfortunately it didn't resolve the problem.

[ceech]

@NeverDie There are two serial ports available in Domoticz. Right? And you have to specify which one you are using in Gateway configuration. Right?

[mfalkvidd]

@ceech you'll need to quite a bit more detailed than that if anyone is to have a chance to help you.

What are the exact commands you used?
What was the output in the terminal?
What did you do in Domoticz?
What does the domoticz log say?

[ceech]

@mfalkvidd Right. This is the Domoticz's part of the setting

And I configured Gateway like this:
./configure --my-transport=nrf24 --my-gateway=ethernet --my-controller-ip-address=192.168.1.120

make
sudo make install

sudo systemctl enable mysgw.service # << adding to boot
sudo systemctl start mysgw.service # << starting

[NeverDie]

I'm going to defer to mfalkvidd. Sounds like he has more of a handle on the Pi version of this, which is what you need. If you're stuck though, try the PC version. Maybe it's easier. Then you can return to the Pi once you get your bearings on how to navigate it.

[mfalkvidd]

@ceech what did sudo ./bin/mysgw -d say at startup and when Domoticz tried to connect?
What does the domoticz log say?

If you run netstat -nap in another terminal window (while mysgw -d is running), does it say something like this?

tcp        0      0 0.0.0.0:5003              0.0.0.0:*               LISTEN    2281/mysgw

[mfalkvidd]

@ceech I think I have located the error.

Domoticz wants to connect to the gateway, but in the configure command --my-controller-ip-address was used. This means that the gateway will connect to the controller, which Domoticz does not support.

So drop --my-controller-ip-address, run the configure command again, run make and start up again.

When I run sudo ./bin/mysgw -d with your configuration I get lots of these:

pi@raspi1:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=R-NG---,VER=2.1.1
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: Eth: connect
mysgw: connect: Connection refused
mysgw: failed to connect

which shows that the gateway is unable to connect to the controller.

[ceech]

@mfalkvidd Removing --my-controller-ip-address did in fact solve the issue.
Thank you for your help.
So, to sum up, these are commands to be used when configuring Gateway for Domoticz ethernet (LAN) connection:

./configure --my-transport=nrf24 --my-gateway=ethernet

make
sudo make install

sudo systemctl enable mysgw.service # << adding to boot
sudo systemctl start mysgw.service # << starting

[mfalkvidd]

@ceech yes and no. Skipping the test step is a bad idea. If that step is skipped, people have to resort to asking questions in the forum ;-)

[ceech]

@mfalkvidd Of course. Skipping test is a bad idea. It is obvious, though that people who resort to asking questions on the forum have tried the test step several times to try and figure things out for themselves. Maybe if the https://www.mysensors.org/build/raspberry wasn't misleading they would even succeed.

[mfalkvidd]

@ceech I'll be happy to update the guide if you could be a bit more specific.

[ceech]

@mfalkvidd First thing one does is to follow instructions exactly and hope things will work out. They don't. You try a different type of connection. Which one? Why one or the other? Which option among the same type? It doesn't work, either. Now, you are thinking, ok this guide is for several controllers, so how do I adapt it for my specific case.
The point being, you can't adapt the instructions on your own. You have to ask someone who's done it before and knows what commands to use in order to make Gateway connect to the specific controller.
For example: using
--my-gateway=ethernet --my-controller-url-address=YOUR-CONTROLLER-ADDRESS
will never connect your Gateway to Domoticz. How can one know that this is the line to be modified?