Barometric Pressure Sensor Using MS5637
-
Thank you so much, it is so close. Code compiles, uploads and there is output from the serial monitor but when adding the device to Vera only a repeater node gets added and not the actual pressure sensor.
The additional pressure sensor files have been uploaded to Vera.
put some delays in here... especially if you do not have the caps on the radio!!!
BaroSensor.begin(); // Register sensors to gw (they will be created as child devices) gw.sendSketchInfo("Pressure Sensor", "1.0"); delay(250); gw.present(BARO_CHILD, S_BARO); delay(250); gw.present(TEMP_CHILD, S_TEMP); delay(250); metric = gw.getConfig().isMetric;if that isn't enough, you can try to add a little more time to the delays....
-
Tried delays right up to 5000 and also added a few others but unfortunately it still only presents the repeater node to Vera
Try deleting the devices it created and starting over. Give it a new device number and try it without it being a repeating node:
change:
gw.begin();to:
gw.begin(NULL, DEVICE_ID, false);where you defined (added) in the header of the sketch:
#define DEVICE_ID 10or some other number that is non-zero and not greater than 254
-
By adding those changes it went back to not outputting to the serial interface. I was able to get it to output again by removing the DEFINE DEVICE ID and the DEVICE ID section (not sure why that made a difference) but then it goes back to only adding a node to Vera.
Really appreciate your determination to solve this and I am learning lots along the way!
-
By adding those changes it went back to not outputting to the serial interface. I was able to get it to output again by removing the DEFINE DEVICE ID and the DEVICE ID section (not sure why that made a difference) but then it goes back to only adding a node to Vera.
Really appreciate your determination to solve this and I am learning lots along the way!
you mind posting the code you tried last?
Can you confirm that you have deleted the Vera devices that were created (I believe you said it was a relay)
-
I have deleted the Vera devices and I have also tried removing and re-adding the MySensors plugin in Vera. When I add the pressure sensor now it still adds as a node. Code is below:
#include <SPI.h>
#include <MySensor.h>
#include <Wire.h>
#include <BaroSensor.h>#define BARO_CHILD 0
#define TEMP_CHILD 1unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in seconds)
MySensor gw;
float lastPressure = -1;
float lastTemp = -1;
int lastForecast = -1;
const char *weather[] = {"stable","sunny","cloudy","unstable","thunderstorm","unknown"};
int minutes;
float pressureSamples[180];
int minuteCount = 0;
bool firstRound = true;
float pressureAvg[7];
float dP_dt;
boolean metric;
MyMessage tempMsg(TEMP_CHILD, V_TEMP);
MyMessage pressureMsg(BARO_CHILD, V_PRESSURE);
MyMessage forecastMsg(BARO_CHILD, V_FORECAST);void setup() {
gw.begin(NULL, false);// Send the sketch version information to the gateway and Controller
gw.sendSketchInfo("Pressure Sensor", "1.0");
delay(1000);
BaroSensor.begin();
delay(1000);
// Register sensors to gw (they will be created as child devices)
gw.present(BARO_CHILD, S_BARO);
delay(1000);
gw.present(TEMP_CHILD, S_TEMP);
delay(1000);
metric = gw.getConfig().isMetric;
}void loop()
{
if(!BaroSensor.isOK())
{
Serial.print("Sensor not Found/OK. Error: ");
Serial.println(BaroSensor.getError());
BaroSensor.begin(); // Try to reinitialise the sensor if we can
}float pressure = BaroSensor.getPressure()/100;
float temperature = BaroSensor.getTemperature();
if (!metric)
{
// Convert to fahrenheit
temperature = temperature * 9.0 / 5.0 + 32.0;
}int forecast = sample(pressure);
Serial.print("Temperature = ");
Serial.print(temperature);
Serial.println(metric?" *C":" *F");
Serial.print("Pressure = ");
Serial.print(pressure);
Serial.println(" Pa");
Serial.println(weather[forecast]);if (temperature != lastTemp) {
gw.send(tempMsg.set(temperature,1));
lastTemp = temperature;
}if (pressure != lastPressure) {
gw.send(pressureMsg.set(pressure, 0));
lastPressure = pressure;
}if (forecast != lastForecast)
{
gw.send(forecastMsg.set(weather[forecast]));
lastForecast = forecast;
}/*
DP/Dt explanation0 = "Stable Weather Pattern"
1 = "Slowly rising Good Weather", "Clear/Sunny "
2 = "Slowly falling L-Pressure ", "Cloudy/Rain "
3 = "Quickly rising H-Press", "Not Stable"
4 = "Quickly falling L-Press", "Thunderstorm"
5 = "Unknown (More Time needed)
*/gw.sleep(SLEEP_TIME);
}int sample(float pressure) {
// Algorithm found here
// http://www.freescale.com/files/sensors/doc/app_note/AN3914.pdf
if (minuteCount > 180)
minuteCount = 6;pressureSamples[minuteCount] = pressure; minuteCount++; if (minuteCount == 5) { // Avg pressure in first 5 min, value averaged from 0 to 5 min. pressureAvg[0] = ((pressureSamples[1] + pressureSamples[2] + pressureSamples[3] + pressureSamples[4] + pressureSamples[5]) / 5); } else if (minuteCount == 35) { // Avg pressure in 30 min, value averaged from 0 to 5 min. pressureAvg[1] = ((pressureSamples[30] + pressureSamples[31] + pressureSamples[32] + pressureSamples[33] + pressureSamples[34]) / 5); float change = (pressureAvg[1] - pressureAvg[0]); if (firstRound) // first time initial 3 hour dP_dt = ((65.0 / 1023.0) * 2 * change); // note this is for t = 0.5hour else dP_dt = (((65.0 / 1023.0) * change) / 1.5); // divide by 1.5 as this is the difference in time from 0 value. } else if (minuteCount == 60) { // Avg pressure at end of the hour, value averaged from 0 to 5 min. pressureAvg[2] = ((pressureSamples[55] + pressureSamples[56] + pressureSamples[57] + pressureSamples[58] + pressureSamples[59]) / 5); float change = (pressureAvg[2] - pressureAvg[0]); if (firstRound) //first time initial 3 hour dP_dt = ((65.0 / 1023.0) * change); //note this is for t = 1 hour else dP_dt = (((65.0 / 1023.0) * change) / 2); //divide by 2 as this is the difference in time from 0 value } else if (minuteCount == 95) { // Avg pressure at end of the hour, value averaged from 0 to 5 min. pressureAvg[3] = ((pressureSamples[90] + pressureSamples[91] + pressureSamples[92] + pressureSamples[93] + pressureSamples[94]) / 5); float change = (pressureAvg[3] - pressureAvg[0]); if (firstRound) // first time initial 3 hour dP_dt = (((65.0 / 1023.0) * change) / 1.5); // note this is for t = 1.5 hour else dP_dt = (((65.0 / 1023.0) * change) / 2.5); // divide by 2.5 as this is the difference in time from 0 value } else if (minuteCount == 120) { // Avg pressure at end of the hour, value averaged from 0 to 5 min. pressureAvg[4] = ((pressureSamples[115] + pressureSamples[116] + pressureSamples[117] + pressureSamples[118] + pressureSamples[119]) / 5); float change = (pressureAvg[4] - pressureAvg[0]); if (firstRound) // first time initial 3 hour dP_dt = (((65.0 / 1023.0) * change) / 2); // note this is for t = 2 hour else dP_dt = (((65.0 / 1023.0) * change) / 3); // divide by 3 as this is the difference in time from 0 value } else if (minuteCount == 155) { // Avg pressure at end of the hour, value averaged from 0 to 5 min. pressureAvg[5] = ((pressureSamples[150] + pressureSamples[151] + pressureSamples[152] + pressureSamples[153] + pressureSamples[154]) / 5); float change = (pressureAvg[5] - pressureAvg[0]); if (firstRound) // first time initial 3 hour dP_dt = (((65.0 / 1023.0) * change) / 2.5); // note this is for t = 2.5 hour else dP_dt = (((65.0 / 1023.0) * change) / 3.5); // divide by 3.5 as this is the difference in time from 0 value } else if (minuteCount == 180) { // Avg pressure at end of the hour, value averaged from 0 to 5 min. pressureAvg[6] = ((pressureSamples[175] + pressureSamples[176] + pressureSamples[177] + pressureSamples[178] + pressureSamples[179]) / 5); float change = (pressureAvg[6] - pressureAvg[0]); if (firstRound) // first time initial 3 hour dP_dt = (((65.0 / 1023.0) * change) / 3); // note this is for t = 3 hour else dP_dt = (((65.0 / 1023.0) * change) / 4); // divide by 4 as this is the difference in time from 0 value pressureAvg[0] = pressureAvg[5]; // Equating the pressure at 0 to the pressure at 2 hour after 3 hours have past. firstRound = false; // flag to let you know that this is on the past 3 hour mark. Initialized to 0 outside main loop. } if (minuteCount < 35 && firstRound) //if time is less than 35 min on the first 3 hour interval. return 5; // Unknown, more time needed else if (dP_dt < (-0.25)) return 4; // Quickly falling LP, Thunderstorm, not stable else if (dP_dt > 0.25) return 3; // Quickly rising HP, not stable weather else if ((dP_dt > (-0.25)) && (dP_dt < (-0.05))) return 2; // Slowly falling Low Pressure System, stable rainy weather else if ((dP_dt > 0.05) && (dP_dt < 0.25)) return 1; // Slowly rising HP stable good weather else if ((dP_dt > (-0.05)) && (dP_dt < 0.05)) return 0; // Stable weather else return 5; // Unknown}
-
@BulldogLowell said:
Try this, and tell me what the serial output looks like.
Have you added a capacitor to the radio? It could be electronic...
#include <SPI.h> #include <MySensor.h> #include <Wire.h> #include <BaroSensor.h> #define BARO_CHILD 0 #define TEMP_CHILD 1 #define DEVICE_ID 99 unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in seconds) MySensor gw; float lastPressure = -1; float lastTemp = -1; int lastForecast = -1; const char *weather[] = {"stable","sunny","cloudy","unstable","thunderstorm","unknown"}; int minutes; float pressureSamples[180]; int minuteCount = 0; bool firstRound = true; float pressureAvg[7]; float dP_dt; boolean metric; MyMessage tempMsg(TEMP_CHILD, V_TEMP); MyMessage pressureMsg(BARO_CHILD, V_PRESSURE); MyMessage forecastMsg(BARO_CHILD, V_FORECAST); void setup() { gw.begin(NULL, DEVICE_ID, false); delay(1000); Serial.println("Got to GW.Begin"); // Send the sketch version information to the gateway and Controller gw.sendSketchInfo("Pressure Sensor", "1.0"); Serial.println("Sketch data Presented"); delay(1000); BaroSensor.begin(); Serial.println("Brometer Sensor started..."); delay(1000); // Register sensors to gw (they will be created as child devices) gw.present(BARO_CHILD, S_BARO); Serial.println("presenting Barometer"); delay(1000); gw.present(TEMP_CHILD, S_TEMP); Serial.println("presenting Thermometer"); delay(1000); metric = gw.getConfig().isMetric; Serial.println("requesting Metric"); delay(1000); Serial.println("Setup Complete"); } void loop() { } -
The Sensor and Ethernet gateway both have 4.7uf electrolytic capacitors across the power input of the radio's (I cant get much distance out of them, maybe <10 metres, but they do work for the relay sensor).
The serial output looks like this: ��Ah���Y5���������� i��`q!���J�����
-
Great, now just plug the loop() back into the sketch, flash your arduino, and you should be good to go
oh... and add a Serial.begin(yourDesiredBaudRate) to setup() ;)
-
Ok, so close! Adding back the rest I get and endless string of � in the serial monitor and nothing adds to Vera.
I don't actually need the temp (tried commenting it out but could not get it to compile) if that makes it easier?
Here is what I have:
#include <SPI.h>
#include <MySensor.h>
#include <Wire.h>
#include <BaroSensor.h>#define BARO_CHILD 0
#define TEMP_CHILD 1
#define DEVICE_ID 99unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in seconds)
MySensor gw;
float lastPressure = -1;
float lastTemp = -1;
int lastForecast = -1;
const char *weather[] = {"stable","sunny","cloudy","unstable","thunderstorm","unknown"};
int minutes;
float pressureSamples[180];
int minuteCount = 0;
bool firstRound = true;
float pressureAvg[7];
float dP_dt;
boolean metric;
MyMessage tempMsg(TEMP_CHILD, V_TEMP);
MyMessage pressureMsg(BARO_CHILD, V_PRESSURE);
MyMessage forecastMsg(BARO_CHILD, V_FORECAST);void setup()
{
Serial.begin(9600);
gw.begin(NULL, DEVICE_ID, false);
delay(1000);
Serial.println("Got to GW.Begin");
// Send the sketch version information to the gateway and Controller
gw.sendSketchInfo("Pressure Sensor", "1.0");
Serial.println("Sketch data Presented");
delay(1000);
BaroSensor.begin();
Serial.println("Brometer Sensor started...");
delay(1000);
// Register sensors to gw (they will be created as child devices)
gw.present(BARO_CHILD, S_BARO);
Serial.println("presenting Barometer");
delay(1000);
gw.present(TEMP_CHILD, S_TEMP);
Serial.println("presenting Thermometer");
delay(1000);
metric = gw.getConfig().isMetric;
Serial.println("requesting Metric");
delay(1000);
Serial.println("Setup Complete");
}void loop()
{
if(!BaroSensor.isOK())
{
Serial.print("Sensor not Found/OK. Error: ");
Serial.println(BaroSensor.getError());
BaroSensor.begin(); // Try to reinitialise the sensor if we can
}float pressure = BaroSensor.getPressure()/100;
float temperature = BaroSensor.getTemperature();
if (!metric)
{
// Convert to fahrenheit
temperature = temperature * 9.0 / 5.0 + 32.0;
}int forecast = sample(pressure);
Serial.print("Temperature = ");
Serial.print(temperature);
Serial.println(metric?" C":" F");
Serial.print("Pressure = ");
Serial.print(pressure);
Serial.println(" Pa");
Serial.println(weather[forecast]);if (temperature != lastTemp) {
gw.send(tempMsg.set(temperature,1));
lastTemp = temperature;
}if (pressure != lastPressure) {
gw.send(pressureMsg.set(pressure, 0));
lastPressure = pressure;
}if (forecast != lastForecast)
{
gw.send(forecastMsg.set(weather[forecast]));
lastForecast = forecast;
}/*
DP/Dt explanation0 = "Stable Weather Pattern"
1 = "Slowly rising Good Weather", "Clear/Sunny "
2 = "Slowly falling L-Pressure ", "Cloudy/Rain "
3 = "Quickly rising H-Press", "Not Stable"
4 = "Quickly falling L-Press", "Thunderstorm"
5 = "Unknown (More Time needed)
*/gw.sleep(SLEEP_TIME);
}int sample(float pressure) {
// Algorithm found here
// http://www.freescale.com/files/sensors/doc/app_note/AN3914.pdf
if (minuteCount > 180)
minuteCount = 6;
pressureSamples[minuteCount] = pressure;
minuteCount++;if (minuteCount == 5) {
// Avg pressure in first 5 min, value averaged from 0 to 5 min.
pressureAvg[0] = ((pressureSamples[1] + pressureSamples[2]
+ pressureSamples[3] + pressureSamples[4] + pressureSamples[5])
/ 5);
} else if (minuteCount == 35) {
// Avg pressure in 30 min, value averaged from 0 to 5 min.
pressureAvg[1] = ((pressureSamples[30] + pressureSamples[31]
+ pressureSamples[32] + pressureSamples[33]
+ pressureSamples[34]) / 5);
float change = (pressureAvg[1] - pressureAvg[0]);
if (firstRound) // first time initial 3 hour
dP_dt = ((65.0 / 1023.0) * 2 * change); // note this is for t = 0.5hour
else
dP_dt = (((65.0 / 1023.0) * change) / 1.5); // divide by 1.5 as this is the difference in time from 0 value.
} else if (minuteCount == 60) {
// Avg pressure at end of the hour, value averaged from 0 to 5 min.
pressureAvg[2] = ((pressureSamples[55] + pressureSamples[56]
+ pressureSamples[57] + pressureSamples[58]
+ pressureSamples[59]) / 5);
float change = (pressureAvg[2] - pressureAvg[0]);
if (firstRound) //first time initial 3 hour
dP_dt = ((65.0 / 1023.0) * change); //note this is for t = 1 hour
else
dP_dt = (((65.0 / 1023.0) * change) / 2); //divide by 2 as this is the difference in time from 0 value
} else if (minuteCount == 95) {
// Avg pressure at end of the hour, value averaged from 0 to 5 min.
pressureAvg[3] = ((pressureSamples[90] + pressureSamples[91]
+ pressureSamples[92] + pressureSamples[93]
+ pressureSamples[94]) / 5);
float change = (pressureAvg[3] - pressureAvg[0]);
if (firstRound) // first time initial 3 hour
dP_dt = (((65.0 / 1023.0) * change) / 1.5); // note this is for t = 1.5 hour
else
dP_dt = (((65.0 / 1023.0) * change) / 2.5); // divide by 2.5 as this is the difference in time from 0 value
} else if (minuteCount == 120) {
// Avg pressure at end of the hour, value averaged from 0 to 5 min.
pressureAvg[4] = ((pressureSamples[115] + pressureSamples[116]
+ pressureSamples[117] + pressureSamples[118]
+ pressureSamples[119]) / 5);
float change = (pressureAvg[4] - pressureAvg[0]);
if (firstRound) // first time initial 3 hour
dP_dt = (((65.0 / 1023.0) * change) / 2); // note this is for t = 2 hour
else
dP_dt = (((65.0 / 1023.0) * change) / 3); // divide by 3 as this is the difference in time from 0 value
} else if (minuteCount == 155) {
// Avg pressure at end of the hour, value averaged from 0 to 5 min.
pressureAvg[5] = ((pressureSamples[150] + pressureSamples[151]
+ pressureSamples[152] + pressureSamples[153]
+ pressureSamples[154]) / 5);
float change = (pressureAvg[5] - pressureAvg[0]);
if (firstRound) // first time initial 3 hour
dP_dt = (((65.0 / 1023.0) * change) / 2.5); // note this is for t = 2.5 hour
else
dP_dt = (((65.0 / 1023.0) * change) / 3.5); // divide by 3.5 as this is the difference in time from 0 value
} else if (minuteCount == 180) {
// Avg pressure at end of the hour, value averaged from 0 to 5 min.
pressureAvg[6] = ((pressureSamples[175] + pressureSamples[176]
+ pressureSamples[177] + pressureSamples[178]
+ pressureSamples[179]) / 5);
float change = (pressureAvg[6] - pressureAvg[0]);
if (firstRound) // first time initial 3 hour
dP_dt = (((65.0 / 1023.0) * change) / 3); // note this is for t = 3 hour
else
dP_dt = (((65.0 / 1023.0) * change) / 4); // divide by 4 as this is the difference in time from 0 value
pressureAvg[0] = pressureAvg[5]; // Equating the pressure at 0 to the pressure at 2 hour after 3 hours have past.
firstRound = false; // flag to let you know that this is on the past 3 hour mark. Initialized to 0 outside main loop.
}if (minuteCount < 35 && firstRound) //if time is less than 35 min on the first 3 hour interval.
return 5; // Unknown, more time needed
else if (dP_dt < (-0.25))
return 4; // Quickly falling LP, Thunderstorm, not stable
else if (dP_dt > 0.25)
return 3; // Quickly rising HP, not stable weather
else if ((dP_dt > (-0.25)) && (dP_dt < (-0.05)))
return 2; // Slowly falling Low Pressure System, stable rainy weather
else if ((dP_dt > 0.05) && (dP_dt < 0.25))
return 1; // Slowly rising HP stable good weather
else if ((dP_dt > (-0.05)) && (dP_dt < 0.05))
return 0; // Stable weather
else
return 5; // Unknown
} -
Ok, so close! Adding back the rest I get and endless string of � in the serial monitor and nothing adds to Vera.
I don't actually need the temp (tried commenting it out but could not get it to compile) if that makes it easier?
Here is what I have:
#include <SPI.h>
#include <MySensor.h>
#include <Wire.h>
#include <BaroSensor.h>#define BARO_CHILD 0
#define TEMP_CHILD 1
#define DEVICE_ID 99unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in seconds)
MySensor gw;
float lastPressure = -1;
float lastTemp = -1;
int lastForecast = -1;
const char *weather[] = {"stable","sunny","cloudy","unstable","thunderstorm","unknown"};
int minutes;
float pressureSamples[180];
int minuteCount = 0;
bool firstRound = true;
float pressureAvg[7];
float dP_dt;
boolean metric;
MyMessage tempMsg(TEMP_CHILD, V_TEMP);
MyMessage pressureMsg(BARO_CHILD, V_PRESSURE);
MyMessage forecastMsg(BARO_CHILD, V_FORECAST);void setup()
{
Serial.begin(9600);
gw.begin(NULL, DEVICE_ID, false);
delay(1000);
Serial.println("Got to GW.Begin");
// Send the sketch version information to the gateway and Controller
gw.sendSketchInfo("Pressure Sensor", "1.0");
Serial.println("Sketch data Presented");
delay(1000);
BaroSensor.begin();
Serial.println("Brometer Sensor started...");
delay(1000);
// Register sensors to gw (they will be created as child devices)
gw.present(BARO_CHILD, S_BARO);
Serial.println("presenting Barometer");
delay(1000);
gw.present(TEMP_CHILD, S_TEMP);
Serial.println("presenting Thermometer");
delay(1000);
metric = gw.getConfig().isMetric;
Serial.println("requesting Metric");
delay(1000);
Serial.println("Setup Complete");
}void loop()
{
if(!BaroSensor.isOK())
{
Serial.print("Sensor not Found/OK. Error: ");
Serial.println(BaroSensor.getError());
BaroSensor.begin(); // Try to reinitialise the sensor if we can
}float pressure = BaroSensor.getPressure()/100;
float temperature = BaroSensor.getTemperature();
if (!metric)
{
// Convert to fahrenheit
temperature = temperature * 9.0 / 5.0 + 32.0;
}int forecast = sample(pressure);
Serial.print("Temperature = ");
Serial.print(temperature);
Serial.println(metric?" C":" F");
Serial.print("Pressure = ");
Serial.print(pressure);
Serial.println(" Pa");
Serial.println(weather[forecast]);if (temperature != lastTemp) {
gw.send(tempMsg.set(temperature,1));
lastTemp = temperature;
}if (pressure != lastPressure) {
gw.send(pressureMsg.set(pressure, 0));
lastPressure = pressure;
}if (forecast != lastForecast)
{
gw.send(forecastMsg.set(weather[forecast]));
lastForecast = forecast;
}/*
DP/Dt explanation0 = "Stable Weather Pattern"
1 = "Slowly rising Good Weather", "Clear/Sunny "
2 = "Slowly falling L-Pressure ", "Cloudy/Rain "
3 = "Quickly rising H-Press", "Not Stable"
4 = "Quickly falling L-Press", "Thunderstorm"
5 = "Unknown (More Time needed)
*/gw.sleep(SLEEP_TIME);
}int sample(float pressure) {
// Algorithm found here
// http://www.freescale.com/files/sensors/doc/app_note/AN3914.pdf
if (minuteCount > 180)
minuteCount = 6;
pressureSamples[minuteCount] = pressure;
minuteCount++;if (minuteCount == 5) {
// Avg pressure in first 5 min, value averaged from 0 to 5 min.
pressureAvg[0] = ((pressureSamples[1] + pressureSamples[2]
+ pressureSamples[3] + pressureSamples[4] + pressureSamples[5])
/ 5);
} else if (minuteCount == 35) {
// Avg pressure in 30 min, value averaged from 0 to 5 min.
pressureAvg[1] = ((pressureSamples[30] + pressureSamples[31]
+ pressureSamples[32] + pressureSamples[33]
+ pressureSamples[34]) / 5);
float change = (pressureAvg[1] - pressureAvg[0]);
if (firstRound) // first time initial 3 hour
dP_dt = ((65.0 / 1023.0) * 2 * change); // note this is for t = 0.5hour
else
dP_dt = (((65.0 / 1023.0) * change) / 1.5); // divide by 1.5 as this is the difference in time from 0 value.
} else if (minuteCount == 60) {
// Avg pressure at end of the hour, value averaged from 0 to 5 min.
pressureAvg[2] = ((pressureSamples[55] + pressureSamples[56]
+ pressureSamples[57] + pressureSamples[58]
+ pressureSamples[59]) / 5);
float change = (pressureAvg[2] - pressureAvg[0]);
if (firstRound) //first time initial 3 hour
dP_dt = ((65.0 / 1023.0) * change); //note this is for t = 1 hour
else
dP_dt = (((65.0 / 1023.0) * change) / 2); //divide by 2 as this is the difference in time from 0 value
} else if (minuteCount == 95) {
// Avg pressure at end of the hour, value averaged from 0 to 5 min.
pressureAvg[3] = ((pressureSamples[90] + pressureSamples[91]
+ pressureSamples[92] + pressureSamples[93]
+ pressureSamples[94]) / 5);
float change = (pressureAvg[3] - pressureAvg[0]);
if (firstRound) // first time initial 3 hour
dP_dt = (((65.0 / 1023.0) * change) / 1.5); // note this is for t = 1.5 hour
else
dP_dt = (((65.0 / 1023.0) * change) / 2.5); // divide by 2.5 as this is the difference in time from 0 value
} else if (minuteCount == 120) {
// Avg pressure at end of the hour, value averaged from 0 to 5 min.
pressureAvg[4] = ((pressureSamples[115] + pressureSamples[116]
+ pressureSamples[117] + pressureSamples[118]
+ pressureSamples[119]) / 5);
float change = (pressureAvg[4] - pressureAvg[0]);
if (firstRound) // first time initial 3 hour
dP_dt = (((65.0 / 1023.0) * change) / 2); // note this is for t = 2 hour
else
dP_dt = (((65.0 / 1023.0) * change) / 3); // divide by 3 as this is the difference in time from 0 value
} else if (minuteCount == 155) {
// Avg pressure at end of the hour, value averaged from 0 to 5 min.
pressureAvg[5] = ((pressureSamples[150] + pressureSamples[151]
+ pressureSamples[152] + pressureSamples[153]
+ pressureSamples[154]) / 5);
float change = (pressureAvg[5] - pressureAvg[0]);
if (firstRound) // first time initial 3 hour
dP_dt = (((65.0 / 1023.0) * change) / 2.5); // note this is for t = 2.5 hour
else
dP_dt = (((65.0 / 1023.0) * change) / 3.5); // divide by 3.5 as this is the difference in time from 0 value
} else if (minuteCount == 180) {
// Avg pressure at end of the hour, value averaged from 0 to 5 min.
pressureAvg[6] = ((pressureSamples[175] + pressureSamples[176]
+ pressureSamples[177] + pressureSamples[178]
+ pressureSamples[179]) / 5);
float change = (pressureAvg[6] - pressureAvg[0]);
if (firstRound) // first time initial 3 hour
dP_dt = (((65.0 / 1023.0) * change) / 3); // note this is for t = 3 hour
else
dP_dt = (((65.0 / 1023.0) * change) / 4); // divide by 4 as this is the difference in time from 0 value
pressureAvg[0] = pressureAvg[5]; // Equating the pressure at 0 to the pressure at 2 hour after 3 hours have past.
firstRound = false; // flag to let you know that this is on the past 3 hour mark. Initialized to 0 outside main loop.
}if (minuteCount < 35 && firstRound) //if time is less than 35 min on the first 3 hour interval.
return 5; // Unknown, more time needed
else if (dP_dt < (-0.25))
return 4; // Quickly falling LP, Thunderstorm, not stable
else if (dP_dt > 0.25)
return 3; // Quickly rising HP, not stable weather
else if ((dP_dt > (-0.25)) && (dP_dt < (-0.05)))
return 2; // Slowly falling Low Pressure System, stable rainy weather
else if ((dP_dt > 0.05) && (dP_dt < 0.25))
return 1; // Slowly rising HP stable good weather
else if ((dP_dt > (-0.05)) && (dP_dt < 0.05))
return 0; // Stable weather
else
return 5; // Unknown
}hard to read your code like that...
indent your code 4 spaces or put it between three ` [backwards apostrophe just left of the 1 on your keyboard]
are you sure your serial monitor is set to the correct speed?
I'd leave compilable alone until you get the devices set up... you didn't delete the vera devices after you got them set with the correct device number before, right?
-
I did delete it but understand now why I shouldn't have. I will re-add it (different device id) and let you know. It may take a little while as I am waiting for some radios with external antennas and an finding in the meantime that my radio reception is too limited to proceed.
