Windows GUI/Controller for MySensors

[Mouridsen]

@tekka Thanks, it works perfect. That was a quite easy fix :)

[tekka]

MYSController Version 0.1.2.278 released

New features:

• Support MYSBootloader 2.0 / SHA (signing bootloader) ==> will be released in the nearest future
• Support 1.5 framework (dev branch)
• Parse MySensors log/debug messages
• Div. options

Changelog:

• Moved send message dialog to main window
• Handler adjustments
• Bugfix FW upload in GW debug mode
• Bugfix message logging

Update via update button in MYSController or download here.

[derry]

Brilliant work! Ran perfectly under Wine on Fedora linux by using /dev/ttyUSB0 for serial port [after first checking my gateway was connected to that port]. Solved a problem I was having with a sensor getting assigned a weird node ID. Saved me loads of time tracking down the problem, many thanks for sharing this tool, much appreciated!

[rickmontana83]

This is awesome!

Any plans to provide source or a back-end API that could be used to connect this up to an HA controller? That way you could control everything downstream in the MySensors cloud from this app, and everything upstream (the HA controller and the cloud) could interface with a much richer (and presumably more robust) infrastructure rather than yet again figuring out how to parse the bits coming off of the serial port...

[ch3b7]

@rickmontana83 parse the data from the serial port is easy, im put in other post in this forum with a part of my code in vb.net

[tekka]

@rickmontana83 Serial API is described here.

[Francois]

@tekka once you flash the Arduino with the MYSBootloader is the only why that now you can programme the Arduino is though the MYSController software?

[tekka]

@Francois AFAIK, MYSController and NodeJsController (see framework, link here) are the only controllers that provide OTA updates via bootloader. Both controllers use the OTA protocol described here. However, MYSBootloader 2.0 will support updates OTA and via IDE.

[Francois]

@tekka the reason I asked I has a problem where I had 2 node with the same node ID and a could not do a OTA via MYSController. As i keep the same ID. I clear the EEPROM and still l it did not work. So the only why I could get the node working was to reflash the boot loader.

[tekka]

@Francois in general, if two nodes have the same ID, you have to disconnect one node and reassign ID/clear eeprom of the other node:

• MYSBootloader 1.1: use the bootloader commands in MYSController (right mouse click on the node, then reassign ID or clear EEPROM)
• MYSBootloader 1.0: upload the clear eeprom sketch and have the controller reassigning the ID

[Francois]

@tekka I doing this and still the node ID is not changing. I change this node to 4 and it still come up as Node 3. The reboot command also don't reboot the device. I have to do a manual reset on the device is this normal?

[tekka]

@Francois ok, I see - can you post or send the log (with debug mode on) to myscontroller at gmail dot com.
If the reboot command is not functioning properly you may have a corrupt routing table: Try clearing the routing table of the node & all routing nodes in between (right mouse click on the node in the routing panel|clear routing table) then try again to reboot.

[Francois]

@tekka will it be a problem if I don't have all my node on the MYSbootloader? Currently I only have 2 of my nodes with MYSBootloader. I am still testing before I change all the nodes

[tekka]

@Francois should be fine

[Francois]

@tekka log file send

[Francois]

@tekka See below it reboot the first time when I try it the seconde time it did
not it just say reboot

Here is my routing Tabel:

[tekka]

@Francois the node has AUTO ID or fix assigned ID (i.e. 91?) - if so, this may be an issue in the dev branch

[rvendrame]

Anyone who owns a Vera controller, and perhaps was able to connect this nice MYSController to the mySensors serial-gateway hooked into Vera USB?

The serial port is exposed in TCP/IP by Vera via ser2net, however I wasn't successful by setting MYSController to <my-vera-ip>:3482 (3482 is the port displayed in Vera -> APPS -> Develop Apps -> Serial port config ) .

(maybe the Vera MYSensor plugin opens the serial connection to GW in 'exclusive' mode or something like that? )

If I remove the GW from Vera USB and plug in my computer, MYSController works fine.

Anyone? Am I wanting too much?

[JoergP]

I'm new to MySensors and playing around with this implementation since some weeks. I implemented an interface from serial to MQTT per python and everything is running fine so far. The last days I spend some time with the bootloader (it is a great feature!!!). I created also a python mqtt client that will take care on that.

I got really crazy the last 2 days with the CRC calculation. I always got a different CRC as as the MYSController. Now I found out, that it seems that the last byte within the HEX file is interpreted as 0xFF instead of the real data. I flashed now one sensor with the MYSController and as I can see in the log-file -> the last byte is read from the HEX as wrong value (0xFF instead of 0x14) -> therefore the HEX file is not flashed correctly (last byte is wrong) -> it seems that this is a bug in MYSController. (I'm using version 0.1.2.278)

Can you check that please?

[tekka]

@JoergP Indeed, bug confirmed. There is an error in the block padding code. I will push the update soon. Thanks for reporting!