Windows GUI/Controller for MySensors
-
@tekka I tried 2 new nodes with static id assigned [gw.begin(incomingMessage, 21, false);] and [gw.begin(NULL, 23, false);] ---- still same frozen response.
10/5/2015 17:18:46 TX 3;255;4;0;3;1400010000000C9486010C94D81A0C94051B0C94AE01
10/5/2015 17:18:46 RX 3;255;4;0;2;140001000000
10/5/2015 17:18:47 INFO BL version=257
10/5/2015 17:18:47 INFO Send FW info to node 3: type=14, version=1, blocks=0x0570, CRC=0xE30B
10/5/2015 17:18:47 TX 3;0;4;0;1;1400010070050BE3
10/5/2015 17:18:47 RX 3;255;4;0;0;1400010070050BE30101
10/5/2015 17:20:32 RX 1;0;1;0;0;19.5and:
10/5/2015 16:59:29 TX 2;255;4;0;3;1400010000000C9486010C94D11A0C94FE1A0C94AE01
10/5/2015 16:59:29 RX 2;255;4;0;2;140001000000
10/5/2015 16:59:29 INFO BL version=257
10/5/2015 16:59:29 INFO Send FW info to node 2: type=14, version=1, blocks=0x0570, CRC=0x2E9E
10/5/2015 16:59:29 TX 2;0;4;0;1;1400010070059E2E
10/5/2015 16:59:29 RX 2;255;4;0;0;1400010070059E2E0101
10/5/2015 17:00:59 RX 24;1;1;0;0;62.8Any idea what the nodes are waiting for?
I also reset the gateway to see if it sent anything that cleared the freeze, but no response. Hmmm.
-
@tekka, problem solved! I took a debug log from the node per your suggestion and was surprised to get:
radio init fail
radio init fail
radio init fail
This of course surprised me after it just finished downloading 20kb+. Turns out after I made the first test of OTA which worked fine, my home network automatically synchronized my laptops & desktop. This brought over a copy of myconfig.h which had softspi enabled! (I had been setting up the gateway on a different computer). So when I went to OTA on the second and third nodes it picked up the synched myconfig.h. Ugh, such little strange things that take so much time to find.
@tekka, my apologies for using some of your time. And my Thanks for your great work and sharing with the community!! Hopefully others will avoid similar mistakes by reading this. -
Hi @tekka , I'm trying to create a simple thermostat device and I'm usually using your fantastic controller for prototype testing and debugging. Now I would need the possibility to send setpoint values from the controller and the current version of MYSController does not seem to support the following:
V_HVAC_SETPOINT_COOL 44 HVAC cold setpoint S_HVAC
V_HVAC_SETPOINT_HEAT 45 HVAC/Heater setpoint S_HVAC, S_HEATER
V_HVAC_FLOW_MODE 46 Flow mode for HVAC ("Auto", "ContinuousOn", "PeriodicOn") S_HVACI would greatly appreciate it is these features were implemented to your fantastic controller also.
Best regards,
Tomas -
sorry if this has been asked before.
but I have a nano with mySbootloader installed and when i look at it in the serial monitor its just all gibberish.
i tried different speeds, but still the same.
is it not possible if you have that bootloader installed? or do i need to do something else.?
thx -
Hi @tekka , I'm trying to create a simple thermostat device and I'm usually using your fantastic controller for prototype testing and debugging. Now I would need the possibility to send setpoint values from the controller and the current version of MYSController does not seem to support the following:
V_HVAC_SETPOINT_COOL 44 HVAC cold setpoint S_HVAC
V_HVAC_SETPOINT_HEAT 45 HVAC/Heater setpoint S_HVAC, S_HEATER
V_HVAC_FLOW_MODE 46 Flow mode for HVAC ("Auto", "ContinuousOn", "PeriodicOn") S_HVACI would greatly appreciate it is these features were implemented to your fantastic controller also.
Best regards,
Tomas -
sorry if this has been asked before.
but I have a nano with mySbootloader installed and when i look at it in the serial monitor its just all gibberish.
i tried different speeds, but still the same.
is it not possible if you have that bootloader installed? or do i need to do something else.?
thx -
@tekka Would it be possible in a future version to have the controller save the detected network nodes? Right know, I have to re-present the nodes in order for them to appear properly in the tree every time MYSController is restarted since it starts up with an empty tree.
-
Hi @tekka , I've gone through the steps in your guide using MQTTGateway as gw sketch.
When I start my new node (burned with mysbootloader) I only see the repeating message "FIND_PARENT" in MySensor Debug window and "RX 0;0;3;0;9;read: 0-0-255 s=255,c=3,t=7,pt=0,l=0,sg=0:" in the MYSController Debug window.
The message appears every time the led is blinking on the node (approx every 2 seconds).Any idea why it doesn't request node id? Have also tried with AutoID without success.
Thx!
-
@tekka Would it be possible in a future version to have the controller save the detected network nodes? Right know, I have to re-present the nodes in order for them to appear properly in the tree every time MYSController is restarted since it starts up with an empty tree.
-
Hi @tekka , I've gone through the steps in your guide using MQTTGateway as gw sketch.
When I start my new node (burned with mysbootloader) I only see the repeating message "FIND_PARENT" in MySensor Debug window and "RX 0;0;3;0;9;read: 0-0-255 s=255,c=3,t=7,pt=0,l=0,sg=0:" in the MYSController Debug window.
The message appears every time the led is blinking on the node (approx every 2 seconds).Any idea why it doesn't request node id? Have also tried with AutoID without success.
Thx!
-
@Anticimex is implemented in the upcoming release :)
-
@Anticimex wanna beta-test? ;)
-
@tekka I feel really, really, REALLY stupid;
I changed the channel in the mysensors config.h to 77, this was the reason no node would ever show up since the default mysbootloader uses the default channel 76.
D'OH
Thanks for your patience and help, everything is working now and I'm really happy!
:+1:@cdr said:
I changed the channel in the mysensors config.h to 77, this was the reason no node would ever show up since the default mysbootloader uses the default channel 76.
I think I am running into the same thing. How did you fix this? I have many nodes so switching back to 76 is not a good option for me.
-
@cdr said:
I changed the channel in the mysensors config.h to 77, this was the reason no node would ever show up since the default mysbootloader uses the default channel 76.
I think I am running into the same thing. How did you fix this? I have many nodes so switching back to 76 is not a good option for me.
-
I did some more testing and my issue definitely appears to be a result of changing the channel in MyConfig.h. I just built a serial gateway with channel 76 selected and everything worked perfectly. The only problem is I have over 20 nodes located throughout my house so re-uploading the code so they use that channel is not something I'd like to do if I can avoid it. Does anyone know how I can recompile the bootloader so I can change the channel?
I tried the files @siklosi posted here http://forum.mysensors.org/topic/2319/how-to-make-complie-mysbootloader/7 but it did not work.
