New RFM69 driver error

firstof9

What arduino ide version do you have?

Arduino: 1.8.5

What Arduino Boards Definitions are you using?
Arduino AVR Boards 1.6.20 (for my Uno with W5100 Ethernet shield)
Adafruit AVR Boards 1.4.12 (for the Feather boards 32u4)

@gohan said in New RFM69 driver error:

Did you try compiling for pro mini?
No as i don't have or use Pro Minis

It does compile for my Nano sensor just fine.
So far the error's only occurred when trying to compile for the Uno.

scalz

I think it happens because of the softspi define, in the w5100 ethernet gw sketch.

could you try my test above please ?

firstof9

@scalz
Your modifications seemed to have resolved the issue.

Also I've made this modification to MyTransport.cpp so it resets the radio on init:

void stInitTransition(void)
{
	#if defined(ADAFRUIT_RFM69)
	pinMode(9, OUTPUT);
	digitalWrite(9, HIGH);
	delay(100);
	digitalWrite(9, LOW);
	delay(100);
	#endif
	TRANSPORT_DEBUG(PSTR("TSM:INIT\n"));

Sketch for reference:

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable Adafruit RFM69 breakout fix
#define ADAFRUIT_RFM69

// Enable and select radio type attached
#define MY_RADIO_RFM69

#define MY_RFM69_NEW_DRIVER // ATC on RFM69 works only with the new driver
#define MY_RFM69_ATC_TARGET_RSSI_DBM (-70)  // target RSSI -70dBm
#define MY_RFM69_MAX_POWER_LEVEL_DBM (10) // amx. TX power 10dBm = 10mW

#define MY_IS_RFM69HW  // Mandatory if you radio module is the high power version (RFM69HW and RFM69HCW), Comment it if it's not the case
#define MY_RF69_FREQUENCY RFM69_915MHZ  // Define for frequency setting. Needed if you're radio module isn't 868Mhz (868Mhz is default in lib)

#define MY_RF69_SPI_CS 4
#define MY_RF69_IRQ_PIN 2
//#define MY_RF69_IRQ_NUM 0

//#define W5100SPIPATCH

#define SKETCH_NAME "MySensors Ethernet Gateway"
#define SKETCH_MAJOR "0"
#define SKETCH_MINOR "5"

// How many clients should be able to connect to this gateway (default 1)
#define MY_GATEWAY_MAX_CLIENTS 2

// Enable gateway ethernet module type
#define MY_GATEWAY_W5100

// Enable Soft SPI for NRF radio (note different radio wiring is required)
// The W5100 ethernet module seems to have a hard time co-operate with 
// radio on the same spi bus.
#if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD)
  #define MY_SOFTSPI
  #define MY_SOFT_SPI_SCK_PIN 14
  #define MY_SOFT_SPI_MISO_PIN 15
  #define MY_SOFT_SPI_MOSI_PIN 16
#endif  

// Enable to UDP
//#define MY_USE_UDP

#define MY_IP_ADDRESS 192,168,1,204   // If this is disabled, DHCP is used to retrieve address
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003

// Controller ip address. Enables client mode (default is "server" mode).
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254

// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 5  // Error led pin
#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  7  // Transmit led pin

#if defined(MY_USE_UDP)
#include <EthernetUdp.h>
#endif
#include <Ethernet.h>
#include <MySensors.h>

void presentation()  
{ 
  // Send the sketch version information to the gateway
  sendSketchInfo(SKETCH_NAME, SKETCH_MAJOR"."SKETCH_MINOR);
}

void setup()
{
}

void loop()
{
}

scalz

@firstof9
reset is already implemented in rf69 driver (see here https://github.com/mysensors/MySensors/blob/master/drivers/RFM69/new/RFM69_new.cpp#L196 )
in your sketch you just need to define it like this

#define MY_RFM69_RST_PIN  your_reset_pin

https://www.mysensors.org/apidocs/group__RFM69SettingGrpPub.html#ga0837813278d8622eb317a3bac22963e7

firstof9

@scalz
I've updated my sketch to include that for the new driver. Thank you.
I had to use that mod for the older driver.

firstof9

@scalz Trying to update all my nodes to the new driver, getting this on the gateway now:

0 MCO:BGN:INIT GW,CP=RPNGA---,VER=2.2.0
3 TSM:INIT
4 TSF:WUR:MS=0
5 RFM69:INIT
11 RFM69:INIT:PIN,CS=4,IQP=2,IQN=0,RST=9
116 RFM69:PTX:LEVEL=5 dBm
118 !RFM69:INIT:SANCHK FAIL
120 !TSM:INIT:TSP FAIL
122 TSM:FAIL:CNT=1
124 TSM:FAIL:DIS
126 TSF:TDI:TSL
128 RFM69:RSL

Same sketch as previously posted (with RFM69 verbose defined for more info). Any ideas?

firstof9

Jumped the gun on a "fixed" post :(

Nightbodom

I have the same error as @firstof9. I have tried all the combinations of arduino (uno, nano) and rfm69, rfm69hw and node, gw sketch and nodemanager... but always got this SANCHK FAIL error...

I solder all rfm69s to nrf2rfm69 converter by @tbowmo

scalz

@nightbodom
If i understand it well, i think firstof9 issue is solved.
Regarding yours, please post more infos else we can't help much.. : hw used, sketch so we can check your defines&code, logs..

Note: it is not recommanded (explained in mysensors docs) to use rfm69 which is not 5V tolerant (3.6v max), with uno/nano which are 5v signal levels boards (SPI is running 5v). For this you would need level shifting board.
Maybe your modules are not dead because of these tests but better be careful.
To be sure, about your modules&sketch, you could try with arduino mini pro 3v/8mhz boards.

SANCHK FAIL means you need to check wiring or change module

Nightbodom

@scalz thanks for advice... I connect modules like sheme on mysensors and watch only for Vcc to be 3V. I try with NodeMCU for gateway and pro mini for node and modules are OK. I use NodeManager for sketches.

But I have another problem. If I use on both (GW and node) rfm69 the range of connection is about 10 -15m trough the wall. So I try to extend range with use of rfm69hw. If I use both hw modules there is no connection even nodes are one by another. If I use one ordinary and one hw module, the range is max. about 1m.

Node is connected through FDTI and NodeMCU is on USB.

node log:

,ft=0,st=OK:4294967270
0 MCO:BGN:INIT NODE,CP=RPNNA---,VER=2.2.0
43 MCO:BGN:BFR
NodeManager v1.7
LIB V=2.2.0 R=P E=- T=N A=A S=- B=-
BATTERY I=201 P=30 T=38
SIGNAL I=202 P=33 T=37
RADIO...108 TSM:INIT
188 TSF:WUR:MS=0
206 RFM69:INIT
223 RFM69:INIT:PIN,CS=10,IQP=2,IQN=0
262 RFM69:PTX:LEVEL=5 dBm
288 TSM:INIT:TSP OK
311 TSM:INIT:STATID=101
335 TSF:SID:OK,ID=101
358 TSM:FPAR
372 RFM69:SWR:SEND,TO=255,RETRY=0
411 TSF:MSG:SEND,101-101-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
1572 RFM69:SAC:SEND ACK,TO=0,RSSI=-31
1615 TSF:MSG:READ,0-0-101,s=255,c=3,t=8,pt=1,l=1,sg=0:0
1675 TSF:MSG:FPAR OK,ID=0,D=1
2490 TSM:FPAR:OK
2506 TSM:ID
2521 TSM:ID:OK
2535 TSM:UPL
2549 RFM69:SWR:SEND,TO=0,RETRY=0
2633 RFM69:SWR:ACK,FROM=0,SEQ=3,RSSI=-73
2676 RFM69:ATC:ADJ TXL,cR=-73,tR=-80,TXL=4
2721 RFM69:PTX:LEVEL=4 dBm
2750 TSF:MSG:SEND,101-101-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2824 RFM69:SAC:SEND ACK,TO=0,RSSI=-31
2867 TSF:MSG:READ,0-0-101,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2926 TSF:MSG:PONG RECV,HP=1
2957 TSM:UPL:OK
2973 TSM:READY:ID=101,PAR=0,DIS=1
3010 RFM69:SWR:SEND,TO=0,RETRY=0
3092 RFM69:SWR:ACK,FROM=0,SEQ=5,RSSI=-72
3135 RFM69:ATC:ADJ TXL,cR=-72,tR=-80,TXL=3
3180 RFM69:PTX:LEVEL=3 dBm
3209 TSF:MSG:SEND,101-101-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
3289 RFM69:SAC:SEND ACK,TO=0,RSSI=-31
3330 TSF:MSG:READ,0-0-101,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
3393 RFM69:SWR:SEND,TO=0,RETRY=0
3497 RFM69:SWR:ACK,FROM=0,SEQ=7,RSSI=-74
3540 RFM69:ATC:ADJ TXL,cR=-74,tR=-80,TXL=2
3586 RFM69:PTX:LEVEL=2 dBm
3614 TSF:MSG:SEND,101-101-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.2.0
3694 RFM69:SWR:SEND,TO=0,RETRY=0
3778 RFM69:SWR:ACK,FROM=0,SEQ=8,RSSI=-73
3821 RFM69:ATC:ADJ TXL,cR=-73,tR=-80,TXL=1
3866 RFM69:PTX:LEVEL=1 dBm
3895 TSF:MSG:SEND,101-101-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
OK
5969 RFM69:SWR:SEND,TO=0,RETRY=0
6057 RFM69:SWR:ACK,FROM=0,SEQ=9,RSSI=-72
6100 RFM69:ATC:ADJ TXL,cR=-72,tR=-80,TXL=0
6146 RFM69:PTX:LEVEL=0 dBm
6174 TSF:MSG:SEND,101-101-0-0,s=255,c=3,t=11,pt=0,l=17,sg=0,ft=0,st=OK:NodeManagerSENSOR
6268 RFM69:SWR:SEND,TO=0,RETRY=0
6350 RFM69:SWR:ACK,FROM=0,SEQ=10,RSSI=-73
6395 RFM69:ATC:ADJ TXL,cR=-73,tR=-80,TXL=-1
6440 RFM69:PTX:LEVEL=-1 dBm
6471 TSF:MSG:SEND,101-101-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
PRES I=201 T=30 D=BATTERY
6549 RFM69:SWR:SEND,TO=0,RETRY=0
6660 RFM69:SWR:ACK,FROM=0,SEQ=11,RSSI=-72
6705 RFM69:ATC:ADJ TXL,cR=-72,tR=-80,TXL=-2
6750 RFM69:PTX:LEVEL=-2 dBm
6780 TSF:MSG:SEND,101-101-0-0,s=201,c=0,t=30,pt=0,l=7,sg=0,ft=0,st=OK:BATTERY
PRES I=202 T=33 D=SIGNAL
6862 RFM69:SWR:SEND,TO=0,RETRY=0
6973 RFM69:SWR:ACK,FROM=0,SEQ=12,RSSI=-73
7016 TSF:MSG:SEND,101-101-0-0,s=202,c=0,t=33,pt=0,l=6,sg=0,ft=0,st=OK:SIGNAL
READY

7096 MCO:REG:REQ
7124 RFM69:SWR:SEND,TO=0,RETRY=0
7206 RFM69:SWR:ACK,FROM=0,SEQ=13,RSSI=-72
7251 TSF:MSG:SEND,101-101-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
7327 RFM69:SAC:SEND ACK,TO=0,RSSI=-30
7368 TSF:MSG:READ,0-0-101,s=255,c=3,t=27,pt=1,l=1,sg=0:1
7430 MCO:PIM:NODE REG=1
7454 MCO:BGN:STP
MY I=101 M=1
INT P=3 M=255
INT P=2 M=255
7475 MCO:BGN:INIT OK,TSP=1
BATTERY V=3.26 %=94
7616 RFM69:SWR:SEND,TO=0,RETRY=0
7720 RFM69:SWR:ACK,FROM=0,SEQ=15,RSSI=-73
7763 TSF:MSG:SEND,101-101-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=0,st=OK:94
SEND D=0 I=201 C=0 T=38 S= I=0 F=3.26
7841 RFM69:SWR:SEND,TO=0,RETRY=0
7964 RFM69:SWR:ACK,FROM=0,SEQ=16,RSSI=-71
8007 TSF:MSG:SEND,101-101-0-0,s=201,c=1,t=38,pt=7,l=5,sg=0,ft=0,st=OK:3.26
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
8089 RFM69:SWR:SEND,TO=0,RETRY=0
8224 RFM69:SWR:ACK,FROM=0,SEQ=17,RSSI=-74
8269 TSF:MSG:SEND,101-101-0-0,s=202,c=1,t=37,pt=5,l=4,sg=0,ft=0,st=OK:4294967270
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
13357 RFM69:SWR:SEND,TO=0,RETRY=0
13494 RFM69:SWR:ACK,FROM=0,SEQ=18,RSSI=-70
13541 TSF:MSG:SEND,101-101-0-0,s=202,c=1,t=37,pt=5,l=4,sg=0,ft=0,st=OK:4294967270
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
18628 RFM69:SWR:SEND,TO=0,RETRY=0
18765 RFM69:SWR:ACK,FROM=0,SEQ=19,RSSI=-71
18812 TSF:MSG:SEND,101-101-0-0,s=202,c=1,t=37,pt=5,l=4,sg=0,ft=0,st=OK:4294967270
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
23898 RFM69:SWR:SEND,TO=0,RETRY=0
24035 RFM69:SWR:ACK,FROM=0,SEQ=20,RSSI=-69
24082 TSF:MSG:SEND,101-101-0-0,s=202,c=1,t=37,pt=5,l=4,sg=0,ft=0,st=OK:4294967270
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
29169 RFM69:SWR:SEND,TO=0,RETRY=0
29462 !RFM69:SWR:NACK
29485 RFM69:PTX:LEVEL=-1 dBm
29523 RFM69:SWR:SEND,TO=0,RETRY=1
29763 !RFM69:SWR:NACK
29786 RFM69:PTX:LEVEL=0 dBm
29855 RFM69:SWR:SEND,TO=0,RETRY=2
30095 !RFM69:SWR:NACK
30117 RFM69:PTX:LEVEL=1 dBm
30146 RFM69:SWR:SEND,TO=0,RETRY=3
30388 !RFM69:SWR:NACK
30410 RFM69:PTX:LEVEL=2 dBm
30480 RFM69:SWR:SEND,TO=0,RETRY=4
30720 !RFM69:SWR:NACK
30742 RFM69:PTX:LEVEL=3 dBm
30803 RFM69:SWR:SEND,TO=0,RETRY=5
31043 !RFM69:SWR:NACK
31066 RFM69:PTX:LEVEL=4 dBm
31135 !TSF:MSG:SEND,101-101-0-0,s=202,c=1,t=37,pt=5,l=4,sg=0,ft=0,st=NACK:4294967270
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
36227 RFM69:SWR:SEND,TO=0,RETRY=0
36519 !RFM69:SWR:NACK
36542 RFM69:PTX:LEVEL=5 dBm
36579 RFM69:SWR:SEND,TO=0,RETRY=1
36818 !RFM69:SWR:NACK
36841 RFM69:PTX:LEVEL=6 dBm
36878 RFM69:SWR:SEND,TO=0,RETRY=2
37117 !RFM69:SWR:NACK
37140 RFM69:PTX:LEVEL=7 dBm
37201 RFM69:SWR:SEND,TO=0,RETRY=3
37441 !RFM69:SWR:NACK
37464 RFM69:PTX:LEVEL=8 dBm
37533 RFM69:SWR:SEND,TO=0,RETRY=4
37773 !RFM69:SWR:NACK
37795 RFM69:PTX:LEVEL=9 dBm
37824 RFM69:SWR:SEND,TO=0,RETRY=5
38066 !RFM69:SWR:NACK
38088 RFM69:PTX:LEVEL=10 dBm
38160 !TSF:MSG:SEND,101-101-0-0,s=202,c=1,t=37,pt=5,l=4,sg=0,ft=1,st=NACK:4294967270
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
43251 RFM69:SWR:SEND,TO=0,RETRY=0
43544 !RFM69:SWR:NACK
43567 RFM69:PTX:LEVEL=11 dBm
43606 RFM69:SWR:SEND,TO=0,RETRY=1
43845 !RFM69:SWR:NACK
43868 RFM69:PTX:LEVEL=12 dBm
43939 RFM69:SWR:SEND,TO=0,RETRY=2
44179 !RFM69:SWR:NACK
44201 RFM69:PTX:LEVEL=13 dBm
44240 RFM69:SWR:SEND,TO=0,RETRY=3
44480 !RFM69:SWR:NACK
44503 RFM69:PTX:LEVEL=14 dBm
44566 RFM69:SWR:SEND,TO=0,RETRY=4
44806 !RFM69:SWR:NACK
44828 RFM69:PTX:LEVEL=15 dBm
44900 RFM69:SWR:SEND,TO=0,RETRY=5
45139 !RFM69:SWR:NACK
45162 RFM69:PTX:LEVEL=16 dBm
45201 !TSF:MSG:SEND,101-101-0-0,s=202,c=1,t=37,pt=5,l=4,sg=0,ft=2,st=NACK:4294967270
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
50292 RFM69:SWR:SEND,TO=0,RETRY=0
50585 !RFM69:SWR:NACK
50608 RFM69:PTX:LEVEL=17 dBm
50638 RFM69:SWR:SEND,TO=0,RETRY=1
50878 !RFM69:SWR:NACK
50900 RFM69:PTX:LEVEL=18 dBm
50964 RFM69:SWR:SEND,TO=0,RETRY=2
51204 !RFM69:SWR:NACK
51226 RFM69:PTX:LEVEL=19 dBm
51298 RFM69:SWR:SEND,TO=0,RETRY=3
51537 !RFM69:SWR:NACK
51560 RFM69:PTX:LEVEL=20 dBm
51599 RFM69:SWR:SEND,TO=0,RETRY=4
51838 !RFM69:SWR:NACK
51861 RFM69:PTX:NO ADJ
51918 RFM69:SWR:SEND,TO=0,RETRY=5
52158 !RFM69:SWR:NACK
52180 RFM69:PTX:NO ADJ
52238 !TSF:MSG:SEND,101-101-0-0,s=202,c=1,t=37,pt=5,l=4,sg=0,ft=3,st=NACK:4294967270
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
57329 RFM69:SWR:SEND,TO=0,RETRY=0
57622 !RFM69:SWR:NACK
57645 RFM69:PTX:NO ADJ
57677 RFM69:SWR:SEND,TO=0,RETRY=1
57917 !RFM69:SWR:NACK
57939 RFM69:PTX:NO ADJ
57997 RFM69:SWR:SEND,TO=0,RETRY=2
58236 !RFM69:SWR:NACK
58259 RFM69:PTX:NO ADJ
58316 RFM69:SWR:SEND,TO=0,RETRY=3
58556 !RFM69:SWR:NACK
58578 RFM69:PTX:NO ADJ
58636 RFM69:SWR:SEND,TO=0,RETRY=4
58875 !RFM69:SWR:NACK
58898 RFM69:PTX:NO ADJ
58955 RFM69:SWR:SEND,TO=0,RETRY=5
59195 !RFM69:SWR:NACK
59217 RFM69:PTX:NO ADJ
59275 !TSF:MSG:SEND,101-101-0-0,s=202,c=1,t=37,pt=5,l=4,sg=0,ft=4,st=NACK:4294967270
BATTERY V=3.26 %=94
60071 RFM69:SWR:SEND,TO=0,RETRY=0
60332 !RFM69:SWR:NACK
60354 RFM69:PTX:NO ADJ
60411 RFM69:SWR:SEND,TO=0,RETRY=1
60651 !RFM69:SWR:NACK
60674 RFM69:PTX:NO ADJ
60731 RFM69:SWR:SEND,TO=0,RETRY=2
60971 !RFM69:SWR:NACK
60993 RFM69:PTX:NO ADJ
61050 RFM69:SWR:SEND,TO=0,RETRY=3
61290 !RFM69:SWR:NACK
61313 RFM69:PTX:NO ADJ
61370 RFM69:SWR:SEND,TO=0,RETRY=4
61609 !RFM69:SWR:NACK
61632 RFM69:PTX:NO ADJ
61689 RFM69:SWR:SEND,TO=0,RETRY=5
61929 !RFM69:SWR:NACK
61952 RFM69:PTX:NO ADJ
62009 !TSF:MSG:SEND,101-101-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=5,st=NACK:94
SEND D=0 I=201 C=0 T=38 S= I=0 F=3.26
62089 RFM69:SWR:SEND,TO=0,RETRY=0
62369 !RFM69:SWR:NACK
62392 RFM69:PTX:NO ADJ
62425 RFM69:SWR:SEND,TO=0,RETRY=1
62664 !RFM69:SWR:NACK
62687 RFM69:PTX:NO ADJ
62711 RFM69:SWR:SEND,TO=0,RETRY=2
62951 !RFM69:SWR:NACK
62973 RFM69:PTX:NO ADJ
63006 RFM69:SWR:SEND,TO=0,RETRY=3
63246 !RFM69:SWR:NACK
63268 RFM69:PTX:NO ADJ
63293 RFM69:SWR:SEND,TO=0,RETRY=4
63533 !RFM69:SWR:NACK
63555 RFM69:PTX:NO ADJ
63612 RFM69:SWR:SEND,TO=0,RETRY=5
63852 !RFM69:SWR:NACK
63875 RFM69:PTX:NO ADJ
63932 !TSF:MSG:SEND,101-101-0-0,s=201,c=1,t=38,pt=7,l=5,sg=0,ft=6,st=NACK:3.26
64014 !TSM:READY:UPL FAIL,SNP
64045 TSM:FPAR
64061 RFM69:SWR:SEND,TO=255,RETRY=0
64104 TSF:MSG:SEND,101-101-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=7,st=OK:
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
64366 !TSF:SND:TNR
66183 !TSM:FPAR:NO REPLY
66209 TSM:FPAR
66224 RFM69:SWR:SEND,TO=255,RETRY=0
66267 TSF:MSG:SEND,101-101-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
68345 !TSM:FPAR:NO REPLY
68370 TSM:FPAR
68386 RFM69:SWR:SEND,TO=255,RETRY=0
68429 TSF:MSG:SEND,101-101-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
69441 !TSF:SND:TNR
70508 !TSM:FPAR:NO REPLY
70533 TSM:FPAR
70549 RFM69:SWR:SEND,TO=255,RETRY=0
70592 TSF:MSG:SEND,101-101-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
72671 !TSM:FPAR:FAIL
72691 TSM:FAIL:CNT=1
72714 TSM:FAIL:DIS
72734 TSF:TDI:TSL
72755 RFM69:RSL
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
74516 !TSF:SND:TNR
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
79591 !TSF:SND:TNR
82774 TSM:FAIL:RE-INIT
82798 TSM:INIT
82812 RFM69:INIT
82831 RFM69:INIT:PIN,CS=10,IQP=2,IQN=0
82874 RFM69:PTX:LEVEL=5 dBm
82903 TSM:INIT:TSP OK
82927 TSM:INIT:STATID=101
82954 TSF:SID:OK,ID=101
82980 TSM:FPAR
82995 RFM69:SWR:SEND,TO=255,RETRY=0
83038 TSF:MSG:SEND,101-101-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
84666 !TSF:SND:TNR
85118 !TSM:FPAR:NO REPLY
85143 TSM:FPAR
85159 RFM69:SWR:SEND,TO=255,RETRY=0
85202 TSF:MSG:SEND,101-101-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
87281 !TSM:FPAR:NO REPLY
87306 TSM:FPAR
87322 RFM69:SWR:SEND,TO=255,RETRY=0
87365 TSF:MSG:SEND,101-101-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
89444 !TSM:FPAR:NO REPLY
89468 TSM:FPAR
89485 RFM69:SWR:SEND,TO=255,RETRY=0
89536 TSF:MSG:SEND,101-101-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
89741 !TSF:SND:TNR
91615 !TSM:FPAR:FAIL
91637 TSM:FAIL:CNT=2
91658 TSM:FAIL:DIS
91678 TSF:TDI:TSL
91699 RFM69:RSL
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
94814 !TSF:SND:TNR
SIGNAL V=-26
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
99887 !TSF:SND:TNR

On 29000 I move gateway far away on another side of laptop..

An here is GW log:

62 MCO:BGN:INIT GW,CP=RPNGE---,VER=2.2.0
105 MCO:BGN:BFR
NodeManager v1.7
LIB V=2.2.0 R=P E=- T=G A=E S=- B=-
SIGNAL I=202 P=33 T=37
RADIO...122 TSF:LRT:OK
228 TSM:INIT
242 TSF:WUR:MS=0
260 RFM69:INIT
276 RFM69:INIT:PIN,CS=15,IQP=5,IQN=5
315 RFM69:PTX:LEVEL=5 dBm
342 TSM:INIT:TSP OK
363 TSM:INIT:GW MODE
385 TSM:READY:ID=0,PAR=0,DIS=0
418 MCO:REG:NOT NEEDED
944 GWT:TIN:CONNECTING...
971 GWT:TIN:IP=192.168.1.30
1001 MCO:BGN:STP
MY I=0 M=255
INT P=3 M=255
INT P=2 M=255
1019 MCO:BGN:INIT OK,TSP=1
SIGNAL V=0
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
1571 TSF:MSG:READ,101-101-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
1632 TSF:MSG:BC
1649 TSF:MSG:FPAR REQ,ID=101
1679 TSF:CKU:OK,FCTRL
1702 TSF:MSG:GWL OK
2422 RFM69:SWR:SEND,TO=101,RETRY=0
2662 !RFM69:SWR:NACK
2692 RFM69:SWR:SEND,TO=101,RETRY=1
2774 RFM69:SWR:ACK,FROM=101,SEQ=1,RSSI=-31
2819 TSF:MSG:SEND,0-0-101-101,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
3747 RFM69:SAC:SEND ACK,TO=101,RSSI=-73
3791 TSF:MSG:READ,101-101-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
3853 TSF:MSG:PINGED,ID=101,HP=1
3891 RFM69:SWR:SEND,TO=101,RETRY=0
4026 RFM69:SWR:ACK,FROM=101,SEQ=3,RSSI=-31
4071 TSF:MSG:SEND,0-0-101-101,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
4206 RFM69:SAC:SEND ACK,TO=101,RSSI=-72
4251 TSF:MSG:READ,101-101-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
4316 RFM69:SWR:SEND,TO=101,RETRY=0
4489 RFM69:SWR:ACK,FROM=101,SEQ=5,RSSI=-31
4534 TSF:MSG:SEND,0-0-101-101,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
4612 RFM69:SAC:SEND ACK,TO=101,RSSI=-74
4656 TSF:MSG:READ,101-101-0,s=255,c=0,t=17,pt=0,l=5,sg=0:2.2.0
RECV S=101 I=255 C=0 T=17 P=2.2.0
4891 RFM69:SAC:SEND ACK,TO=101,RSSI=-73
4936 TSF:MSG:READ,101-101-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
RECV S=101 I=255 C=3 T=6 P=
7172 RFM69:SAC:SEND ACK,TO=101,RSSI=-72
7216 TSF:MSG:READ,101-101-0,s=255,c=3,t=11,pt=0,l=17,sg=0:NodeManagerSENSOR
RECV S=101 I=255 C=3 T=11 P=NodeManagerSENSOR
7465 RFM69:SAC:SEND ACK,TO=101,RSSI=-73
7509 TSF:MSG:READ,101-101-0,s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
RECV S=101 I=255 C=3 T=12 P=1.0
7774 RFM69:SAC:SEND ACK,TO=101,RSSI=-72
7818 TSF:MSG:READ,101-101-0,s=201,c=0,t=30,pt=0,l=7,sg=0:BATTERY
RECV S=101 I=201 C=0 T=30 P=BATTERY
8086 RFM69:SAC:SEND ACK,TO=101,RSSI=-73
8130 TSF:MSG:READ,101-101-0,s=202,c=0,t=33,pt=0,l=6,sg=0:SIGNAL
RECV S=101 I=202 C=0 T=33 P=SIGNAL
8321 RFM69:SAC:SEND ACK,TO=101,RSSI=-72
8365 TSF:MSG:READ,101-101-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
8432 RFM69:SWR:SEND,TO=101,RETRY=0
8528 RFM69:SWR:ACK,FROM=101,SEQ=13,RSSI=-30
8574 TSF:MSG:SEND,0-0-101-101,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
8834 RFM69:SAC:SEND ACK,TO=101,RSSI=-73
8878 TSF:MSG:READ,101-101-0,s=255,c=3,t=0,pt=1,l=1,sg=0:94
RECV S=101 I=255 C=3 T=0 P=
9077 RFM69:SAC:SEND ACK,TO=101,RSSI=-71
9122 TSF:MSG:READ,101-101-0,s=201,c=1,t=38,pt=7,l=5,sg=0:3.26
RECV S=101 I=201 C=1 T=38 P=
9339 RFM69:SAC:SEND ACK,TO=101,RSSI=-74
9383 TSF:MSG:READ,101-101-0,s=202,c=1,t=37,pt=5,l=4,sg=0:4294967270
RECV S=101 I=202 C=1 T=37 P=
14607 RFM69:SAC:SEND ACK,TO=101,RSSI=-70
14653 TSF:MSG:READ,101-101-0,s=202,c=1,t=37,pt=5,l=4,sg=0:4294967270
RECV S=101 I=202 C=1 T=37 P=
19878 RFM69:SAC:SEND ACK,TO=101,RSSI=-71
19924 TSF:MSG:READ,101-101-0,s=202,c=1,t=37,pt=5,l=4,sg=0:4294967270
RECV S=101 I=202 C=1 T=37 P=
25148 RFM69:SAC:SEND ACK,TO=101,RSSI=-69
25193 TSF:MSG:READ,101-101-0,s=202,c=1,t=37,pt=5,l=4,sg=0:4294967270
RECV S=101 I=202 C=1 T=37 P=
SIGNAL V=-69
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
SIGNAL V=-69
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
SIGNAL V=-69
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
SIGNAL V=-69
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00
SIGNAL V=-69
SEND D=0 I=202 C=0 T=37 S= I=0 F=0.00

For node I use :

// RFM69 radio settings
#define MY_RADIO_RFM69
//#define MY_RFM69_FREQUENCY RFM69_868MHZ
#define MY_IS_RFM69HW
#define MY_RFM69_NEW_DRIVER
//#define MY_RFM69_ENABLE_ENCRYPTION
//#define MY_RFM69_NETWORKID 100
#define MY_DEBUG_VERBOSE_RFM69
//#define MY_RF69_IRQ_PIN 2
//#define MY_RF69_IRQ_NUM MY_RF69_IRQ_PIN
//#define MY_RF69_SPI_CS 10
//#define MY_RFM69_ATC_MODE_DISABLED

And for GW same as this except without MY_IS_RFM69HW.

Any sugestions?

scalz

@Nightbodom

It could also be

bad antennas: what's your antenna ? in case of "wire" antenna, what kind of wire do you use? It needs to be one solid core, 86mm for 868mhz.
power supply too. maybe not enough beefy ftdi on your node, when you increase distance and need more power to transmit.

you could eliminate power supply point, by replacing it with 2xaa battery, or any other batt as long as you keep your vcc 3.3. it would provide a more clean power supply

Maybe you could upload a pic of your gw and node assembly, in case we see something.

If everything is ok, then i'll recheck hw&sw here, but i can't tell you when for the moment.

firstof9

@scalz Negitive my issue persists using the new driver. I've had to revert back to the old driver to get around this SANCHK FAIL. Same wiring same radios using older driver work perfectly fine.

I read some where that the issue is resolved in beta version of 2.2.1.

scalz

@firstof9 said in New RFM69 driver error:

@scalz
I've updated my sketch to include that for the new driver. Thank you.
I had to use that mod for the older driver.

Why did you say this 4months ago? Does it mean you got it working with new driver at a moment?
Then 3months later, you said you got hw sanity check error. What has changed?
Maybe, have you updated lib and get again your initial problem??

On other side, (if i get things right), nightbodom has no more sanity chech error but range issue now..

Inconsistent details with hard to follow debug :crystal_ball: , unfortunately no time actually. I'll take a look later.

firstof9

@scalz Sorry, your changes fixed my OP problem with the compile errors. I forgot to follow up noting the TSP INIT fails and switching back to the old driver :(

New RFM69 driver error

18

11.7k

11.2k

113.1k