Combination of gateway and relay code
-
Hi. I am an amateur programmer. I connected the buzzer to the gate and added the alarm functionality. It works but if the gateway gets some data from other sensor, the alarm stops working.
/** * The MySensors Arduino library handles the wireless radio link and protocol * between your home built sensors/actuators and HA controller of choice. * The sensors forms a self healing radio network with optional repeaters. Each * repeater and gateway builds a routing tables in EEPROM which keeps track of the * network topology allowing messages to be routed to nodes. * * Created by Henrik Ekblad <henrik.ekblad@mysensors.org> * Copyright (C) 2013-2015 Sensnology AB * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors * * Documentation: http://www.mysensors.org * Support Forum: http://forum.mysensors.org * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * version 2 as published by the Free Software Foundation. * ******************************* * * DESCRIPTION * The ArduinoGateway prints data received from sensors on the serial link. * The gateway accepts input on seral which will be sent out on radio network. * * The GW code is designed for Arduino Nano 328p / 16MHz * * Wire connections (OPTIONAL): * - Inclusion button should be connected between digital pin 3 and GND * - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series * * LEDs (OPTIONAL): * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly * - ERR (red) - fast blink on error during transmission error or recieve crc error * */ // Enable debug prints to serial monitor #define MY_DEBUG // Enable and select radio type attached #define MY_RADIO_NRF24 //#define MY_RADIO_RFM69 // Set LOW transmit power level as default, if you have an amplified NRF-module and // power your radio separately with a good regulator you can turn up PA level. #define MY_RF24_PA_LEVEL RF24_PA_LOW // Enable serial gateway #define MY_GATEWAY_SERIAL // Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender) #if F_CPU == 8000000L #define MY_BAUD_RATE 38400 #endif // Enable inclusion mode #define MY_INCLUSION_MODE_FEATURE // Enable Inclusion mode button on gateway //#define MY_INCLUSION_BUTTON_FEATURE // Inverses behavior of inclusion button (if using external pullup) //#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP // Set inclusion mode duration (in seconds) #define MY_INCLUSION_MODE_DURATION 60 // Digital pin used for inclusion mode button //#define MY_INCLUSION_MODE_BUTTON_PIN 3 // Set blinking period #define MY_DEFAULT_LED_BLINK_PERIOD 300 // Inverses the behavior of leds //#define MY_WITH_LEDS_BLINKING_INVERSE // Flash leds on rx/tx/err // Uncomment to override default HW configurations //#define MY_DEFAULT_ERR_LED_PIN 4 // Error led pin //#define MY_DEFAULT_RX_LED_PIN 6 // Receive led pin //#define MY_DEFAULT_TX_LED_PIN 5 // the PCB, on board LED #include <MySensors.h> #define RELAY_1 3 // Arduino Digital I/O pin number for first relay (second on pin+1 etc) #define NUMBER_OF_RELAYS 1 // Total number of attached relays #define RELAY_ON 1 // GPIO value to write to turn on attached relay #define RELAY_OFF 0 // GPIO value to write to turn off attached relay void before() { pinMode(RELAY_1, OUTPUT); // Set relay to last known state (using eeprom storage) digitalWrite(RELAY_1, LOW); } void setup() { // Setup locally attached sensors pinMode(A0, OUTPUT); } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("Relay", "1.0"); present(1, S_BINARY); } void receive(const MyMessage &message) { // We only expect one type of message from controller. But we better check anyway. if (message.type==V_STATUS) { while (message.getBool() == 1){ beep(); } } // Write some debug info Serial.print("Incoming change for sensor:"); Serial.print(message.sensor); Serial.print(", New status: "); Serial.println(message.getBool()); } void loop() { } void beep() { tone(A0, 4200); //Wygeneruj sygnał o częstotliwości 4000Hz na pinie A5 wait(100); noTone(A0); wait(100); tone(A0, 4200); //Wygeneruj sygnał o częstotliwości 4000Hz na pinie A5 wait(100); noTone(A0); wait(10000); }```
-
@scalpel this code
while (message.getBool() == 1){ beep(); }
instructs the gateway to beep forever. There is no code in beep() that will change message, it will always be the same message.
-
But if gateway receive some data from sensors, example temperature it stop beeping. Maybe while function should be in loop()?
look
2018-04-02 19:54:21.356 User: mietek initiated a switch command (771/Alarm/On) /<<---START BEEPING
2018-04-02 19:54:21.465 (ArduinoOdbiornik) Lighting 2 (Alarm)
2018-04-02 19:54:21.588 Error: OTGW: Error received!
2018-04-02 19:54:34.675 (OpenTherm) Temp (Control Setpoint)
2018-04-02 19:54:34.682 (OpenTherm) General/Percentage (Maximum Relative Modulation Level)
2018-04-02 19:54:34.688 (OpenTherm) Thermostat (Zadana ogrzewania)
2018-04-02 19:54:34.694 (OpenTherm) General/Percentage (Modulacja palnika)
2018-04-02 19:54:34.700 (OpenTherm) Temp (Isense)
2018-04-02 19:54:34.708 (OpenTherm) Temp (Boiler Water Temperature)
2018-04-02 19:54:34.714 (OpenTherm) Temp (DHW Temperature)
2018-04-02 19:54:34.720 (OpenTherm) Temp (Outside Temperature)
2018-04-02 19:54:34.725 (OpenTherm) Temp (Return Water Temperature)
2018-04-02 19:54:34.731 (OpenTherm) Thermostat (DHW Setpoint)
2018-04-02 19:54:34.735 (OpenTherm) Thermostat (Max_CH Water Setpoint)
2018-04-02 19:54:51.739 Error: OTGW: Error received!
2018-04-02 19:55:20.879 Error: OTGW: Error received!
2018-04-02 19:55:21.434 (rflink) Temp (Zewnątrz)
2018-04-02 19:55:32.899 (ArduinoOdbiornik) Temp (Parter) // <<--- STOP BEEPING
-
@scalpel could you move the debug info prints in receive() to the beginning of receive() instead of the end, and re-run your test and post the result?
-
I will try tomorrow. Thanks
-
Need more tests, but looks like it works. Thanks