Combination of gateway and relay code

[scalpel]

Hi. I am an amateur programmer. I connected the buzzer to the gate and added the alarm functionality. It works but if the gateway gets some data from other sensor, the alarm stops working.

/**
* The MySensors Arduino library handles the wireless radio link and protocol
* between your home built sensors/actuators and HA controller of choice.
* The sensors forms a self healing radio network with optional repeaters. Each
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
* network topology allowing messages to be routed to nodes.
*
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
* Copyright (C) 2013-2015 Sensnology AB
* Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
*
* Documentation: http://www.mysensors.org
* Support Forum: http://forum.mysensors.org
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
*******************************
*
* DESCRIPTION
* The ArduinoGateway prints data received from sensors on the serial link.
* The gateway accepts input on seral which will be sent out on radio network.
*
* The GW code is designed for Arduino Nano 328p / 16MHz
*
* Wire connections (OPTIONAL):
* - Inclusion button should be connected between digital pin 3 and GND
* - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
*
* LEDs (OPTIONAL):
* - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error
*
*/

// Enable debug prints to serial monitor
#define MY_DEBUG


// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level.
#define MY_RF24_PA_LEVEL RF24_PA_LOW

// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE

// Inverses behavior of inclusion button (if using external pullup)
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP

// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE

// Flash leds on rx/tx/err
// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED

#include <MySensors.h>

#define RELAY_1  3  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 1 // Total number of attached relays
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay

void before()
{
  
    pinMode(RELAY_1, OUTPUT);
    // Set relay to last known state (using eeprom storage)
    digitalWrite(RELAY_1, LOW);
  
}
void setup()
{
	// Setup locally attached sensors
 pinMode(A0, OUTPUT);
}

void presentation()
{
	// Send the sketch version information to the gateway and Controller
  sendSketchInfo("Relay", "1.0");
  present(1, S_BINARY);
  
}

void receive(const MyMessage &message)
{
  // We only expect one type of message from controller. But we better check anyway.
   if (message.type==V_STATUS) {
  
    while (message.getBool() == 1){
    beep();
    }
   
    
    }
 
   
   
    // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.print(message.sensor);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
  }


void loop()
{
	
}


void beep()
{
    tone(A0, 4200); //Wygeneruj sygnał o częstotliwości 4000Hz na pinie A5  
    wait(100);  
    noTone(A0);
    wait(100);
    tone(A0, 4200); //Wygeneruj sygnał o częstotliwości 4000Hz na pinie A5  
    wait(100);  
    noTone(A0);
    wait(10000);

}```

[mfalkvidd]

@scalpel this code

while (message.getBool() == 1){
beep();
}

instructs the gateway to beep forever. There is no code in beep() that will change message, it will always be the same message.

[scalpel]

But if gateway receive some data from sensors, example temperature it stop beeping. Maybe while function should be in loop()?

look

2018-04-02 19:54:21.356 User: mietek initiated a switch command (771/Alarm/On) /<<---START BEEPING
2018-04-02 19:54:21.465 (ArduinoOdbiornik) Lighting 2 (Alarm)
2018-04-02 19:54:21.588 Error: OTGW: Error received!
2018-04-02 19:54:34.675 (OpenTherm) Temp (Control Setpoint)
2018-04-02 19:54:34.682 (OpenTherm) General/Percentage (Maximum Relative Modulation Level)
2018-04-02 19:54:34.688 (OpenTherm) Thermostat (Zadana ogrzewania)
2018-04-02 19:54:34.694 (OpenTherm) General/Percentage (Modulacja palnika)
2018-04-02 19:54:34.700 (OpenTherm) Temp (Isense)
2018-04-02 19:54:34.708 (OpenTherm) Temp (Boiler Water Temperature)
2018-04-02 19:54:34.714 (OpenTherm) Temp (DHW Temperature)
2018-04-02 19:54:34.720 (OpenTherm) Temp (Outside Temperature)
2018-04-02 19:54:34.725 (OpenTherm) Temp (Return Water Temperature)
2018-04-02 19:54:34.731 (OpenTherm) Thermostat (DHW Setpoint)
2018-04-02 19:54:34.735 (OpenTherm) Thermostat (Max_CH Water Setpoint)
2018-04-02 19:54:51.739 Error: OTGW: Error received!
2018-04-02 19:55:20.879 Error: OTGW: Error received!
2018-04-02 19:55:21.434 (rflink) Temp (Zewnątrz)
2018-04-02 19:55:32.899 (ArduinoOdbiornik) Temp (Parter) // <<--- STOP BEEPING

[mfalkvidd]

@scalpel could you move the debug info prints in receive() to the beginning of receive() instead of the end, and re-run your test and post the result?

[scalpel]

I will try tomorrow. Thanks

[scalpel]

Need more tests, but looks like it works. Thanks