SmartSleep wake up message always get NACK

Henrik Nielsen

I guess if I could just turn off the wake up / post-sleep message, everything would still kinda work. MyController will react to the pre-sleep message and send any pending messages, so the problem is just the 2 seconds of wasted battery everytime it try to send the wake up messages.

There might of course be other implications that I am not aware of :)

berkseo

@henrik-nielsen
I banished your sketch. Faced the same problem, have not seen before. As it turned out, this is a problem of quality of radio modules and radio driver settings. The solution is described below.

Was before:


 __  __       ____
|  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
| |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
| |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
|_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
        |___/                      2.3.1-alpha

18 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.3.1-alpha
28 TSM:INIT
28 TSF:WUR:MS=0
36 TSM:INIT:TSP OK
38 TSF:SID:OK,ID=100
40 TSM:FPAR
77 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
600 TSF:MSG:READ,0-0-100,s=255,c=3,t=8,pt=1,l=1,sg=0:0
606 TSF:MSG:FPAR OK,ID=0,D=1
2088 TSM:FPAR:OK
2088 TSM:ID
2091 TSM:ID:OK
2093 TSM:UPL
2099 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2205 TSF:MSG:READ,0-0-100,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2211 TSF:MSG:PONG RECV,HP=1
2215 TSM:UPL:OK
2217 TSM:READY:ID=100,PAR=0,DIS=1
2222 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2357 TSF:MSG:READ,0-0-100,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2365 TSF:MSG:SEND,100-100-0-0,s=255,c=0,t=17,pt=0,l=11,sg=0,ft=0,st=OK:2.3.1-alpha
2375 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2838 TSF:MSG:READ,0-0-100,s=255,c=3,t=6,pt=0,l=1,sg=0:M
2846 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=11,pt=0,l=14,sg=0,ft=0,st=OK:SmartSleepTest
2856 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
2867 TSF:MSG:SEND,100-100-0-0,s=1,c=0,t=36,pt=0,l=4,sg=0,ft=0,st=OK:Info
2875 MCO:REG:REQ
2912 !TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=NACK:2
4923 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=1,st=OK:2
4995 TSF:MSG:READ,0-0-100,s=255,c=3,t=27,pt=1,l=1,sg=0:1
5001 MCO:PIM:NODE REG=1
5003 MCO:BGN:STP
5005 MCO:BGN:INIT OK,TSP=1
6008 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
6017 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:600
6625 TSF:TDI:TSL
6627 MCO:SLP:WUP=-1
6629 TSF:TRI:TSB
8312 !TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:3000
10524 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
10532 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=1,st=OK:600
11141 TSF:TDI:TSL
11143 MCO:SLP:WUP=-1
11145 TSF:TRI:TSB
12828 !TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:3000
15036 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
15044 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=1,st=OK:600
15652 TSF:TDI:TSL

1.Go to the folder - C:\Users\Andrey\Documents\Arduino\libraries\MySensors-development

2.Next, go to the folder - \drivers\RF24

3.Open the file - RF24registers.h

4.Change the parameters to these:
...lines 42-47.

// ARD, auto retry delay

#define RF24_SET_ARD (10)
// ARD, auto retry count

#define RF24_SET_ARC (15)

5.Next, open the file-RF24.ccp
Change the parameters to these:
...line 67
...line 114

delayMicroseconds(100);

The problem in radio driver, in his settings, apparently all wrote according to the Datasheet, but in life a bit otherwise)))

Has now become:

 
 __  __       ____
|  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
| |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
| |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
|_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
        |___/                      2.3.1-alpha

18 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.3.1-alpha
28 TSM:INIT
28 TSF:WUR:MS=0
38 TSM:INIT:TSP OK
43 TSF:SID:OK,ID=100
45 TSM:FPAR
102 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2111 !TSM:FPAR:NO REPLY
2113 TSM:FPAR
2170 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2736 TSF:MSG:READ,0-0-100,s=255,c=3,t=8,pt=1,l=1,sg=0:0
2742 TSF:MSG:FPAR OK,ID=0,D=1
4182 TSM:FPAR:OK
4182 TSM:ID
4184 TSM:ID:OK
4186 TSM:UPL
4194 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
4300 TSF:MSG:READ,0-0-100,s=255,c=3,t=25,pt=1,l=1,sg=0:1
4306 TSF:MSG:PONG RECV,HP=1
4311 TSM:UPL:OK
4311 TSM:READY:ID=100,PAR=0,DIS=1
4319 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
4450 TSF:MSG:READ,0-0-100,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
4462 TSF:MSG:SEND,100-100-0-0,s=255,c=0,t=17,pt=0,l=11,sg=0,ft=0,st=OK:2.3.1-alpha
4474 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
4939 TSF:MSG:READ,0-0-100,s=255,c=3,t=6,pt=0,l=1,sg=0:M
4950 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=11,pt=0,l=14,sg=0,ft=0,st=OK:SmartSleepTest
4966 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
4976 TSF:MSG:SEND,100-100-0-0,s=1,c=0,t=36,pt=0,l=4,sg=0,ft=0,st=OK:Info
4984 MCO:REG:REQ
5021 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
5308 TSF:MSG:READ,0-0-100,s=255,c=3,t=27,pt=1,l=1,sg=0:1
5314 MCO:PIM:NODE REG=1
5316 MCO:BGN:STP
5318 MCO:BGN:INIT OK,TSP=1
6322 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
6334 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:600
6942 TSF:TDI:TSL
6944 MCO:SLP:WUP=-1
6946 TSF:TRI:TSB
6952 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=OK:3000
9164 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
9177 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:600
9785 TSF:TDI:TSL
9787 MCO:SLP:WUP=-1
9789 TSF:TRI:TSB
9797 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=OK:3000
12005 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
12017 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:600
12625 TSF:TDI:TSL

use.. ;)

Henrik Nielsen

It works :D You're a wizard @berkseo :)

I do infact use the cheap radio modules from china, so I think you're right about the possible lacking of quality in the hardware :/

I guess there is not a way I can change these settings somewhere local to my sketch, so they do not get overwritten the next time I update the MySensors lib?

Anyway, it's great that it works now, and I will just bookmark this topic for future reference.

Thank again for your assistance :)

berkseo

@henrik-nielsen
Everyone uses cheap radio modules, it's a reality. One thing is technical specifications, the other is real network on real equipment. Although I think if you take a very original radios, it will be the same in 99%)). ....Glad to help, it's called a community.

Henrik Nielsen

@berkseo I just started wondering if "everyone" uses cheap chinese radios, should this fix be part of the official code base?

Maybe just as something that could be enabled if needed.

scalz

@henrik-nielsen said in SmartSleep wake up message always get NACK:

if "everyone" uses cheap chinese radios, should this fix be part of the official code base?

simple! add issue or pull request to mysensors github. that's the easiest way when there's issue to fix ;)
because the team can't follow all forum topics and make todolist, in this way this is not handy.

berkseo

@scalz said in SmartSleep wake up message always get NACK:

pull request

I made a pull request. I think that this will accept. Apparently the next version will already be. ...I'm not sure this is absolutely perfect, a mistake in the first message after sleeping mostly. Perhaps later it is better to modify startListening, although, of course, now it is a good solution, but not ideal.

Henrik Nielsen

@berkseo Great :) I am currently trying to figure out what my employers policy for open source contributions made in their employees spare time is, so I could make the pull request myself, but you beat me to it :(

Memphis007

@berkseo Hi, could you post the link to your pull request ? I don't see any traces of it in MySensors Github repository.

BTW with my setup (genuine/good quality NRF24L01) increase lines 67 & 114 of RF24.ccp to 50 do the trick.

Thanks.

mfalkvidd

@memphis007 berseo's pull requests (link 1, link 2) were closed in favor of this pull request.

Memphis007

@mfalkvidd I have applied Tekka007 pull request successfully, all is working correctly now. Thanks !

SmartSleep wake up message always get NACK

13

11.7k

11.2k

113.1k