@tbowmo I deleted all the files and reinstalled the Arduino IDE. Placed the library as you said and everything works! Thanks and sorry for the inconvenience!

@mfalkvidd thank you. I was disappointed when I sat how it formatted. I will check your suggestions today.

@mfalkvidd

Sorry to leave you hanging for so long. Was finally able to start my troubleshooting of the node today. Turns out it did end up being a wiring issue, filed as "Technician Error". Rather than having both the reed switches share a common ground, I had one sensor grounding to the data pin of the other.

Hi all. I have been searching for a way to power nodes and stumbled across this project. My question is is this a viable and safe solution if I just recreate the ac-dc portion on perf board? In essence I want to create a good 5v power supply that can be hardwired into my home inside of an electrical box. Not necessarily in the wall but in less accessible places like attics and such.

@mfalkvidd

Sorry to leave you hanging for so long. Was finally able to start my troubleshooting of the node today. Turns out it did end up being a wiring issue, filed as "Technician Error". Rather than having both the reed switches share a common ground, I had one sensor grounding to the data pin of the other.

@mfalkvidd thank you. I was disappointed when I sat how it formatted. I will check your suggestions today.

Hoping for some help from the MySensors experts. Im running a home automation system using Domoticz as my controller and MySensors 2.0 Library for my nodes. I noticed the close proximity of my front door and my garage door and wanted to save a microcontroller and radio by having it handle the reed switches for both doors. First off I do not consider myself a coder Im much more of a hardware kind of guy. I ended up cobbling this sketch together by looking at an example I found in the forums and looking at the included binary switch sketch.

My issue is when I open the front door, both the garage door and front door indicators on my Domoticz dashboard change state. When I open and close the garage door only the garage door indicator changes state. I suspect it has something to do with how the pin ID's are assigned but I just am not very strong in that department. Any help would be appreciated.

/**

• The MySensors Arduino library handles the wireless radio link and protocol
• between your home built sensors/actuators and HA controller of choice.
• The sensors forms a self healing radio network with optional repeaters. Each
• repeater and gateway builds a routing tables in EEPROM which keeps track of the
• network topology allowing messages to be routed to nodes.
• Created by Henrik Ekblad henrik.ekblad@mysensors.org
• Copyright (C) 2013-2015 Sensnology AB
• Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
• Documentation: http://www.mysensors.org
• Support Forum: http://forum.mysensors.org
• This program is free software; you can redistribute it and/or
• modify it under the terms of the GNU General Public License
• version 2 as published by the Free Software Foundation.

• DESCRIPTION
• Simple binary switch example
• Connect button or door/window reed switch between
• digitial I/O pin 3 (BUTTON_PIN below) and GND.
• http://www.mysensors.org/build/binary
  */

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define CHILD_ID_1 3
#define BUTTON_PIN_1 3 // Arduino Digital I/O pin for button/reed switch
#define CHILD_ID_2 4
#define BUTTON_PIN_2 4 // Arduino Digital I/O pin for button/reed switch

Bounce debouncer1 = Bounce();
Bounce debouncer2 = Bounce();

int oldValue1=-1;
int oldValue2=-1;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg1(CHILD_ID_1,V_TRIPPED);
MyMessage msg2(CHILD_ID_2,V_TRIPPED);

void setup()
{
// Setup the button
pinMode(BUTTON_PIN_1,INPUT);
pinMode(BUTTON_PIN_2,INPUT);
// Activate internal pull-up
digitalWrite(BUTTON_PIN_1,HIGH);
digitalWrite(BUTTON_PIN_2,HIGH);

// After setting up the button, setup debouncer
debouncer1.attach(BUTTON_PIN_1);
debouncer1.interval(5);
debouncer2.attach(BUTTON_PIN_2);
debouncer2.interval(5);
}

void presentation() {
// Register binary input sensor to gw (they will be created as child devices)
// You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage.
// If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
present(CHILD_ID_1, S_DOOR);
present(CHILD_ID_2, S_DOOR);
}

// Check if digital input has changed and send in new value
void loop()
{
{
debouncer1.update();
// Get the update value
int value1 = debouncer1.read();

if (value1 != oldValue1) {
  // Send in the new value
  send(msg1.set(value1==HIGH ? 1 : 0));
  oldValue1 = value1;

}
}

{
debouncer2.update();
// Get the update value
int value2 = debouncer2.read();

if (value2 != oldValue2) {
  // Send in the new value
  send(msg2.set(value2==HIGH ? 1 : 0));
  oldValue2 = value2;

}
}
}

@tlpeter I had not, thanks so much! I'm still a novice when it comes to GitHub, how do I download the files?

hmm... is it possible I somehow got an incomplete library? I only have 4 sketches that begin with D and none of them are that one.

I wanted to update all my sensor to the 2.0 library but Im noticing that the Humidity sketch seems to have been removed. Is this correct?

@tbowmo I deleted all the files and reinstalled the Arduino IDE. Placed the library as you said and everything works! Thanks and sorry for the inconvenience!

So first I tried placing the entire folder in ~/Arduino. No luck there. Then left that folder where it was and copied the Libraries folder from Arduino-Master into ~/Arduino/Libraries. No luck. Nothing was showing up under sketchbook either.

I then placed the Arduino-Master in ~/sketchbook and that allowed me to see the library in the Arduino IDE but I still get the same error. I then copied the Library folder from Arduino-Master into ~/sketchbook/libraries and still came out with the same error. Im considering doing a fresh Arduino IDE install.

Running Arduino IDE version 1.6.9 with the newest MySensors Library and Ubuntu 16.04

Hi Guys,

I am struggling to import the MySensors library into Arduino IDE. I have spent the last two days googling and trying things to no avail. I am running Ubuntu 16.04.

I have the Arduino IDE installed ant it is functional. I can upload one of the example codes to a Arduino MicroController and it works. I can even see the MySensors Library under sketchbook. The problem arises when i try and use any of the codes bundled in the MySensors library. When I try and verify the code I get the following error...

Arduino: 1.6.9 (Linux), Board: "Arduino Nano, ATmega328"

/home/dane/sketchbook/Arduino-master/libraries/MySensors/examples/HumiditySensor/HumiditySensor.ino:31:24: fatal error: MySensor.h: No such file or directory
#include <MySensor.h>
^
compilation terminated.
exit status 1
Error compiling for board Arduino Nano.

Any help would be GREATLY appreciated.