Thank you to all for your rapid answer.

@Amster
I saw the fuse in Mouser website, I think the same one is the following:

http://www.mouser.it/ProductDetail/Littelfuse/0875200MXEP/?qs=%2Fha2pyFadugxaz6Ka1QIzhvtD8HnMnU0Sbd%2Fe9cxA257in2%2FbECi0w==

I also called they and they told me that only after I will put the order they check the real availability in the various site they have and if present they send me, but if not present I have to wait 10 Week as this is the Factory Lead Time.
And more of this the shipping will cost 20€, so a total of 39,80€ for 10 little fuse I think is too much.

@Nca78

I think I will go for the one you suggest. It's cheap, with free shipping and it seems not to big to don't fit in the board.

Now I will have to wait about 1 month before all parts arrive, then I will let you know if fuse will fit or not.

Thank you again for your attention and a big hello from Italy.

@TimO

Thank you very much for your help, now I succesfully connected my iboard card as LAN Gateway without doing any HW modification and even any software modification to any library, simply using the sketch you sent here.

For general information to other people that want to use the iboard card with Domoticz, to avoid any problem like the following:

2016-12-18 12:06:40.840 MySensors: trying to connect to: 192.168.1.133:5603
2016-12-18 12:06:41.841 MySensors: connected to: 192.168.1.133:5603
2016-12-18 12:06:45.841 MySensors: Connection reset!
2016-12-18 12:06:45.842 TCP: Reconnecting in 30 seconds...

Consider to use the Arduino IDE 1.6.8 to compile and upload the sketch, otherwise, with newest Arduino IDE you will get the error messages above.

Thank you again for you help and a big hello to all the members of the forum.

Regards

@TimO

Thank you very much for your help, now I succesfully connected my iboard card as LAN Gateway without doing any HW modification and even any software modification to any library, simply using the sketch you sent here.

For general information to other people that want to use the iboard card with Domoticz, to avoid any problem like the following:

2016-12-18 12:06:40.840 MySensors: trying to connect to: 192.168.1.133:5603
2016-12-18 12:06:41.841 MySensors: connected to: 192.168.1.133:5603
2016-12-18 12:06:45.841 MySensors: Connection reset!
2016-12-18 12:06:45.842 TCP: Reconnecting in 30 seconds...

Consider to use the Arduino IDE 1.6.8 to compile and upload the sketch, otherwise, with newest Arduino IDE you will get the error messages above.

Thank you again for you help and a big hello to all the members of the forum.

Regards

Dear All,

I just buyed an iboard and following your instruction I tried to get it working in my domoticz configuration, but without success.

As at today MySensors library is updated to ver. 2, can you please tell me how to proceed in order to have it working correctly ?

I used the sketch available in MySensors Library in my arduino IDE 1.6.13, but I never able to ping it from my computer.

As for now I prefere don't go for hardware modification, can you please suggest me what kind of modification I have to do and where I have to do it ?

Because I don't know if I have to modify only the sketch or if I have to modify the file MyConfig.h or what other file I have to modify.

Thank you in advance for your help.

@Yveaux
Hi Yveaux, I want to know if it's possible to connect more than one PIR sensor at the same node and if there's a limit on the number.

I mean the possibility to have only 1 node with connected more PIR sensor in order to avoid the moltiplication of the assembly composed by arduino+radio+PIR+power supply.

I imagine (but I'm not sure) if I connect more PIR sensor to the same PIN3 on arduino node I will obtain a "network" of PIR Sensor reacting as a single element to a possible presence, without the possibility to differentiate the area interested by the alarm.

If I can differentiate the PIN where I can connect the PIR sensor, maybe I can get information from each single area of detection controlled by the PIR sensor.

Thank you for your attention.

Hi to everyone,
it's possible to connect more than one PIR Sensor to the same board ?
In case if it's possible, there's a limit on that number ?

Thank you for your help

Thank you to all for your rapid answer.

@Amster
I saw the fuse in Mouser website, I think the same one is the following:

http://www.mouser.it/ProductDetail/Littelfuse/0875200MXEP/?qs=%2Fha2pyFadugxaz6Ka1QIzhvtD8HnMnU0Sbd%2Fe9cxA257in2%2FbECi0w==

I also called they and they told me that only after I will put the order they check the real availability in the various site they have and if present they send me, but if not present I have to wait 10 Week as this is the Factory Lead Time.
And more of this the shipping will cost 20€, so a total of 39,80€ for 10 little fuse I think is too much.

@Nca78

I think I will go for the one you suggest. It's cheap, with free shipping and it seems not to big to don't fit in the board.

Now I will have to wait about 1 month before all parts arrive, then I will let you know if fuse will fit or not.

Thank you again for your attention and a big hello from Italy.

Dear All,

I'm interested in build some exemplar of this beautiful project, so for that reason I ordered all the items present in Bill Of Material.

I ordererd most of the item without problem, but I get in trouble in finding the "Slow Blow Fuse (250v 0.2A)", as in the link given, the 0.2A fuse is not available and in plus the seller doesn't send to Italy.

For that reason I started a search in a lot of different shop, from the most knowed to the less knowed, but I'm not able to find it for a reasonable price.
As example I found a Company that sell 10 of it for a total of 3.40$ but they ship it for 35$, so I think is a nonsense.
Other Company only sell minimum quantity of 1000 item, but I don't need that amount and in plus the price will become very high.

So for that reason I ask you if someone can suggest me an internet shop where I can find it for a reasonable price (item+shipping), or eventually if it's possible to substitute that "Slow Blow Fuse (250v 0.2A)" with different kind of fuse maybe more easy to find.

Or as a last chance, if someone eventually have 10 of it and is available to send me (off course I will pay for the item and for the shipping) in Italy.

Thank you in advance for your attention.

@Rod-MacPherson
Dear Rod, thank you for the suggestion you gave me.
Following the instruction you indicated me, I was able to make the sketch working with new MySensors 2.0 library.

Considering that I'm not a programmer, it was quite easy to make the sketch working.

Thank you again for your suggestion and off course thank you to BartE for the good original work he did.

If someone need new sketch working with library 2.0, feel free to ask me.

Dear All,

I'm a newbie and I found in MySensors website the project for RFID Lock Sensors that use PN532 RFID Reader, but as I already have with me a RC-522 RFID reader, searching on the forum I found this post that I thinked it will suit my case.

I assembled the various hardware parts as described on first post, but when I copied the sketch code in my arduino IDE, I'm not able to get it work.

I get some error message that is not so clear for me.

It's seems the sketch is for a previous version of MySensors Library or Arduino IDE, but I'm not sure of this.

As I use Arduino IDE 1.6.12 that has included MySensors Library 2.0.0, is the Sketch you included in the first post already valid for that setup ?

It' will be possible to have a valid sketch working with new setup or eventually to know how to proceed to make the actual one working ?

Thank you in advance for your attention.