@mfalkvidd My problem is the following:
i have 2 sensors DS1820D with promini
Same sketch (except nodeid)
One is OK: far from 1-2 meter from the Pigateway
The other one (t° of my swimming pool) if far from max 10 m.. :works a few times (every 15 minutes).. then stop sendind

I become crazy: i changed the power from battery to a 9v connected to a 3,3 V convertor connected on raw ..

Thks for any idee ?
Where do i have to change the code to have a PA_MAX for the PiGateway when i test with
/usr/local/sbin/PiGatewaySerial

Starting PiGatewaySerial...
Protocol version - 1.4
Created PTY '/dev/pts/0'
Gateway tty: /dev/ttyMySensorsGateway
================ SPI Configuration ================
CSN Pin = CE0 (PI Hardware Driven)
CE Pin = Custom GPIO25
Clock Speed = 8 Mhz
================ NRF Configuration ================
STATUS = 0x0e RX_DR=0 TX_DS=0 MAX_RT=0 RX_P_NO=7 TX_FULL=0
RX_ADDR_P0-1 = 0xa8a8e1fc00 0xa8a8e1fc00
RX_ADDR_P2-5 = 0xff 0xc4 0xc5 0xc6
TX_ADDR = 0xe7e7e7e7e7
RX_PW_P0-6 = 0x20 0x20 0x20 0x00 0x00 0x00
EN_AA = 0x3b
EN_RXADDR = 0x06
RF_CH = 0x4c
RF_SETUP = 0x23
CONFIG = 0x0e
DYNPD/FEATURE = 0x3f 0x06
Data Rate = 250KBPS
Model = nRF24L01+
CRC Length = 16 bits
PA Power = PA_LOW

I met problems with sensors and nrf2l01.
How can i change the PA_LEVEL from PA_LOW to PA_MAX
Here is the start of the gateway
================ SPI Configuration ================
CSN Pin = CE0 (PI Hardware Driven)
CE Pin = Custom GPIO25
Clock Speed = 8 Mhz
================ NRF Configuration ================
STATUS = 0x0e RX_DR=0 TX_DS=0 MAX_RT=0 RX_P_NO=7 TX_FULL=0
RX_ADDR_P0-1 = 0xa8a8e1fc00 0xa8a8e1fc00
RX_ADDR_P2-5 = 0xff 0xc4 0xc5 0xc6
TX_ADDR = 0xa8a8e1fc0a
RX_PW_P0-6 = 0x20 0x20 0x20 0x00 0x00 0x00
EN_AA = 0x3b
EN_RXADDR = 0x06
RF_CH = 0x4c
RF_SETUP = 0x23
CONFIG = 0x0e
DYNPD/FEATURE = 0x3f 0x06
Data Rate = 250KBPS
Model = nRF24L01+
CRC Length = 16 bits
PA Power = PA_LOW

Tks for your help

@Tore-André-Rosander
Tks a lot
It works's fine!!
pi@JpPi2 ~ $ ssh JpPi3
_ ____ _ _____
| |_ __ | _ ()__ /
_ | | '_ | |) | | |
| || | |) | /| |) |
_/| ._/|| ||___/
||

Welcome to Raspbian GNU/Linux 8.0 (jessie) (4.4.7-v7+).

System information as of: Wed Jun 1 09:10:09 CEST 2016

System load: 0.01 IP Address:
Memory usage: 17.9% System uptime: 1 day
Usage on /: 27% Swap usage: 0.0%
Local Users: 1 Processes: 126

Last login: Wed Jun 1 09:03:53 2016 from raspberryjp

@Tore-André-Rosander
Tks a lot for your answer.. It seems to look like what i want at logon..Iwill test it.
I keep you in touch!

@Sander-Stolk hi
how do you achieve to have a nice 'logon' screen ou your PI: Domotics Logo, @ip,memory,date... etc etc..
Im' newbee on raspberry from france
HAve a nice day
JP
i really want to have the same or any available sample like yours

| _ \ | | ()
| | | |__ _ __ ___ ___ | |_ _ ___ ____
| | | / _ | '_ ` _ \ / _ | | |/ | /
| |/ / () | | | | | | () | |_| | ( / /
|/ _/|| || ||___/ _||_/|

Last login: Mon Apr 11 12:10:24 2016 from 192.168.1.34

Monday, 11 April 2016, 12:12:45 pm CEST
Linux 4.1.18-v7+ armv7l GNU/Linux
Uptime.............: 0 days, 00h00m25s
Memory.............: 770952kB (Free) / 948056kB (Total)
Load Averages......: 0.59, 0.16, 0.05 (1, 5, 15 min)
Running Processes..: 100
IP Addresses.......: 192.168.1.14

Hi
Like you, i'have got a lot a problem to connect nano pro mini with a serial gateway on a raspeberry
Everything is fine on with a Arduino Uno.i think there are problems with the 3,3 V pover on tte nano pro mini
I keep on investigating..
TRy to connect with UNO with gateway sketch and one UNO with sensor sketch.. and everyting wikk be ok..
As you i'm newbee

Hi
something is missing..

Is there a problem with the repository
Tks a lot for your job!

pi@domoticjp ~ $ sudo git clone https://github.com/mysensors/Raspberry.git
Cloning into 'Raspberry'...
remote: Counting objects: 273, done.
remote: Compressing objects: 100% (3/3), done.
remote: Total 273 (delta 0), reused 0 (delta 0), pack-reused 270
Receiving objects: 100% (273/273), 215.00 KiB | 0 bytes/s, done.
Resolving deltas: 100% (114/114), done.
Checking connectivity... done.
pi@domoticjp ~ $ cd Raspberry/librf24-bcm
-bash: cd: Raspberry/librf24-bcm: No such file or directory

@jelluz
I have got he sme configuration between Arduiono et a PIGATEWAYSERIAL ?
How do you declare it into a controler like Pimatic (you says that it works fine)
Tkd for your advice