@Juan-González-M. said in NRF24 i cant configure raspberry pi1:
Same problem here.
If you solve the problem please tell me.
@Juan-González-M. said in NRF24 i cant configure raspberry pi1:
Same problem here.
If you solve the problem please tell me.
@mfalkvidd
may be all my nrf24 are damaged, i have 3.
Is there any way to check if they are good?
If the connections are well made should work correct?
And is an external source even necessary?
tomorrow i will test what do you say me now, because now have to go to work.
@mfalkvidd
yes i changed gnd As you told me,,,and not work.
after that i confirm again all wires...and not work again.... then i connect more two nrf24...make sudo reboot
and run sudo ./bin/mysgw -d
but the error is the same,,, so a decide help with external source 3.3v
i connected wire power nrf24 ---> power external source
gnd powersource -------> other gnd raspberry pi
sudo reboot again...
after sudo ./bin/mysgw -d
and the error is the same.....
@mfalkvidd you are correct. I confirm all the wires 5 times.
but the error is the same.
after that i changed my nrf for two other that i had, and the error is the same.
exist any way to confirm if the nrf24 is working fine? may be my nrf are damaged. i dont know.
edit: I tried to , connect POWER NRF24 to external power, and connect ground external power to ground raspberry pi.. and the result is the same.
TSM:INIT:TSP FAIL
@mfalkvidd ok no problem i waiting
@mfalkvidd lol ok, i am newbie sorry for the stupid acts.
1 ./configure --my-transport=nrf24 --my-gateway=ethernet --my-port=5003 --my-gateway=ethernet --my-controller-ip-address=192.168.1.65
2 make
3 sudo ./bin/mysgw -h
4 sudo ./bin/mysgw -d
result:
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT
@mfalkvidd
ok thank you so...i make this:
1 git clone https://github.com/mysensors/MySensors.git --branch master
cd MySensors
2 ./configure --my-transport=nrf24
3 ./configure --my-gateway=ethernet --my-port=5003
4 ./configure --my-gateway=ethernet --my-controller-ip-address=192.168.1.65
5 make
6 sudo ./bin/mysgw -h
7 sudo ./bin/mysgw -d
and i receive this:
pi@hassbian:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT
mysgw: TSM:FAIL:RE-INIT
mysgw: TSM:INIT
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=2
mysgw: TSM:FAIL:PDT
what is the problem?
@mfalkvidd
ok, already actived SPY
[SECTION] Detecting target machine.
[OK] machine detected: SoC=unknown, Type=unknown, CPU=armv6l.
[SECTION] Checking GPIO Sysfs.
[OK] /sys/class/gpio/export found
[SECTION] Detecting SPI driver.
[OK] SPI driver detected:SPIDEV.
[SECTION] Detecting init system.
[OK] init system detected: systemd.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.
now what the frequency i should in this line:
--my-transport=rfm69 --my-rfm69-frequency=868 --my-is-rfm69hw
remember i use nrf24 no rfm69
@Rodolfo-Vieira said in NRF24 i cant configure raspberry pi1:
[SECTION] Detecting SPI driver.
[WARNING] No supported SPI driver detected
@mfalkvidd ahhhh ok sorry, now i can solve this problem:
[SECTION] Detecting SPI driver.
[WARNING] No supported SPI driver detected