I changed cables, get new NRF24L01+ PA/LNA and make clean install of rasbian. Nothing helped, but then out of nothing it started to work (at least no fail). Its a mystery to me why. Thank you all for help.

pi@raspberrypi:~/MySensors $ sudo ./bin/mysgw
Jan 12 10:05:42 INFO  Starting gateway...
Jan 12 10:05:42 INFO  Protocol version - 2.3.1
Jan 12 10:05:42 DEBUG Serial port /dev/ttyUSB020 (115200 baud) created
Jan 12 10:05:42 DEBUG MCO:BGN:INIT GW,CP=RNNGL-Q-,REL=255,VER=2.3.1
Jan 12 10:05:42 DEBUG TSF:LRT:OK
Jan 12 10:05:42 DEBUG TSM:INIT
Jan 12 10:05:42 DEBUG TSF:WUR:MS=0
Jan 12 10:05:42 DEBUG !TSM:INIT:TSP FAIL
Jan 12 10:05:42 DEBUG TSM:FAIL:CNT=1
Jan 12 10:05:42 DEBUG TSM:FAIL:DIS
Jan 12 10:05:42 DEBUG TSF:TDI:TSL
Jan 12 10:05:52 DEBUG TSM:FAIL:RE-INIT
Jan 12 10:05:52 DEBUG TSM:INIT
Jan 12 10:05:52 DEBUG !TSM:INIT:TSP FAIL
Jan 12 10:05:52 DEBUG TSM:FAIL:CNT=2
Jan 12 10:05:52 DEBUG TSM:FAIL:DIS
Jan 12 10:05:52 DEBUG TSF:TDI:TSL
^CJan 12 10:05:53 NOTICE Received SIGINT

pi@raspberrypi:~/MySensors $ sudo ./bin/mysgw
Jan 12 10:14:30 INFO  Starting gateway...
Jan 12 10:14:30 INFO  Protocol version - 2.3.1
Jan 12 10:14:30 DEBUG Serial port /dev/ttyUSB020 (115200 baud) created
Jan 12 10:14:30 DEBUG MCO:BGN:INIT GW,CP=RNNGL-Q-,REL=255,VER=2.3.1
Jan 12 10:14:30 DEBUG TSF:LRT:OK
Jan 12 10:14:30 DEBUG TSM:INIT
Jan 12 10:14:30 DEBUG TSF:WUR:MS=0
Jan 12 10:14:30 DEBUG TSM:INIT:TSP OK
Jan 12 10:14:30 DEBUG TSM:INIT:GW MODE
Jan 12 10:14:30 DEBUG TSM:READY:ID=0,PAR=0,DIS=0
Jan 12 10:14:30 DEBUG MCO:REG:NOT NEEDED
Jan 12 10:14:30 DEBUG MCO:BGN:STP
Jan 12 10:14:30 DEBUG MCO:BGN:INIT OK,TSP=1
Jan 12 10:14:30 DEBUG TSM:READY:NWD REQ
Jan 12 10:14:30 DEBUG TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:```

@gohan Yes it worked on Arduino board and about a year ago it even worked on Raspberry. So I thought its software issue.

@vidin --my-transport=nrf24 returns [ERROR] Invalid transport type.

@mfalkvidd

Hi, can somebody help me resolve !TSM:INIT:TSP FAIL? I proceeded according to https://www.mysensors.org/build/raspberry but I get error and not sure where is the problem:

./configure --my-transport=rf24 --my-rf24-irq-pin=15 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyMySensorsGateway

sudo ./bin/mysgw
Dec 31 11:07:50 INFO  Starting gateway...
Dec 31 11:07:50 INFO  Protocol version - 2.3.1
Dec 31 11:07:50 DEBUG Serial port /dev/ttyMySensorsGateway (115200 baud) created
Dec 31 11:07:50 DEBUG MCO:BGN:INIT GW,CP=RNNGL-Q-,REL=255,VER=2.3.1
Dec 31 11:07:50 DEBUG TSF:LRT:OK
Dec 31 11:07:50 DEBUG TSM:INIT
Dec 31 11:07:50 DEBUG TSF:WUR:MS=0
Dec 31 11:07:50 DEBUG !TSM:INIT:TSP FAIL
Dec 31 11:07:50 DEBUG TSM:FAIL:CNT=1
Dec 31 11:07:50 DEBUG TSM:FAIL:DIS
Dec 31 11:07:50 DEBUG TSF:TDI:TSL
...

Double checked wiring of NRF24L01+ with 100uf capacitor, NRF24L01+ works OK on my arduino.

RPi 3 B, Debian 9.3 Stretch