Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Anyone ever look into ezbl (aka easy booloader) on a PIC?

NeverDie Hero Member last edited by NeverDie

It would seem to offer a very smooth and simple path toward doing OTA firmware updates over a variety of different microcontrollers and would be radio agnostic.

Bootloader Made Easy with EZBL – 03:49
— Microchip Technology, Inc.

Works on most 16 bit PICs and all 32 bit PICs.
Reply Quote 0
1 Reply Last reply

1
Posts

242
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3310
Views

No one has replied
MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

11

0
Votes

11
Posts

53
Views

@dpcons MQTT sounds intimidating and looks imitimidating when you see all of the options available. Here's the scenario: You want to send a message. That's the -m option followed by a space and the message between " " the location, topic, is a tree, -t option, separated by forward slash / eg. MyRootTopic/MyTopicsSub/MyTopicSubSub It's as easy as that if your broker, the MQTT service (program) is on the same computer as the sending program. Usually it's not. Specifiy the location, the host, of the broker with the -h option followed by the host name or IP address The retain option, -r is important but explaining it is beyone the scope of this message Receiving, subscribing, to a topic is just the same, but you wouldn't have the -m message If you subscribe from the command line, the subscribe function waits indefinitely for messages published to the subscribed topic (unless you use the -C option) ^C to terminate the command. A tamotized device with the MQTT configured will create a number of topics on the broker. Home Assistant will see this automatically, if you have the Tasmota and MQTT Integrations installed. The MySensors MQTT gateway takes care of MQTT communication for a MySensors device. Again the MySensors and MQTT integrations. I use both. -OSD
Radio waking up for no reason.
Development • • Sasquatch

3

0
Votes

3
Posts

37
Views

Over 4 years on, and my node ran continuously sending 4 messages every 5 minutes. It's 700mAh LiFePo4 battery voltage dropped from initial 3.45V to 3.24V, according to LiFePo4 voltge/SoC tables It's just under 40% left. 700*60% = 420mAh. 100 mAH per year. using library 2.40 and blob message I could cut usage to ~25mAh/year, not bad
PJON and Minicore not working
Development • • Trand

1

0
Votes

1
Posts

14
Views

No one has replied
Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

3

1
Votes

3
Posts

25
Views

@mfalkvidd Thank you very much, that's exactly what I was looking for!
Saving last known good state, but not in EEPROM
Development • • OldSurferDude

6

0
Votes

6
Posts

33
Views

@OldSurferDude jus request counter states from controller on each reset, worked fine with Domoticz... or save in eeprom but increase location every write, on power up/reset search eeprom for largest value stored and carry on from that location, one long integer will fit 256 times in atmega328(p) eeprom, is that long enough for you ?

Anyone ever look into ezbl (aka easy booloader) on a PIC?

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

Radio waking up for no reason.
Development • • Sasquatch

PJON and Minicore not working
Development • • Trand

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

32
Online

11.6k
Users

11.2k
Topics

113.0k
Posts

Anyone ever look into ezbl (aka easy booloader) on a PIC?

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

MQTT-Help me understand about the MQTT Gateway. Development • • dpcons

Radio waking up for no reason. Development • • Sasquatch

PJON and Minicore not working Development • • Trand

Counting Incoming and Outgoing Messages from a Gateway Development • • Trand

Saving last known good state, but not in EEPROM Development • • OldSurferDude

32Online

11.6kUsers

11.2kTopics

113.0kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

Radio waking up for no reason.
Development • • Sasquatch

PJON and Minicore not working
Development • • Trand

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

32
Online

11.6k
Users

11.2k
Topics

113.0k
Posts