Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

MySensors over Bluetooth ?

alowhum Plugin Developer 28 May 2020, 18:00 last edited by alowhum 28 May 2020, 18:01

Looking at the BLE Nano and the new Bluetooth Arduino devices, I was wondering if the mysensors protocol could run on top of Bluetooth?

Is it a crazy idea? Is it even technically possible? Could it, for example, extract away handling of encryption?
Reply Quote 0
1 Reply Last reply
Loading More Posts
4
Posts

49
Views
Reply

Reply as topic
Log in to reply
scalz Hardware Contributor 28 May 2020, 19:00 last edited by scalz 28 May 2020, 19:02
technically yes this is possible by using:
- custom BLE msg, depends on payload length, and longer payload can be enabled
- BLE Serial service
but afaik there is no plan for adding and maintaining this for the moment
Reply Quote 2
1 Reply Last reply
alowhum Plugin Developer 28 May 2020, 22:31 last edited by

Interesting. Would this automatically secure the communicatin?
Reply Quote 0
1 Reply Last reply
scalz Hardware Contributor 28 May 2020, 22:42 last edited by

no. bluetooth is not secured by default. you need to handle this in your ble fw
Reply Quote 0
1 Reply Last reply

4
Posts

49
Views

Log in to reply

1 out of 4

Suggested Topics

Update RF24 library to latest version
Bug Reports • 23 Mar 2014, 23:37 • andriej 24 Mar 2014, 22:52

4

0
Votes

4
Posts

2.6k
Views

24 Mar 2014, 22:52

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
Which device I have to use to connect with accelerometer before connecting to my pc?
General Discussion • 24 Jan 2023, 17:16 • Yada Kijsathan 16 Mar 2025, 20:17

5

1
Votes

5
Posts

40
Views

16 Mar 2025, 20:17

When connecting an accelerometer to your PC, consider its communication protocol (I2C or SPI) and the appropriate interface device, like a microcontroller (e.g., Arduino). You may also need additional hardware for voltage adjustment or signal conditioning, depending on the sensor’s specifications.
Why is the output of ACS712 current measurement module unchanged?
General Discussion • mysensors • 19 Jul 2021, 09:09 • Tessie T 28 days ago

4

0
Votes

4
Posts

37
Views

28 days ago

@ZenBlizzard in case you are measuring the output with a multimeter, you will get an averaged level, since AC current waveform should be sinusoidal and overlapped with the Vcc/2->2.56V in your case. To measure the current you need a decently high sampling and some math. #define SENSITIVITY 66 // mV/A const float readings = 5; const float alpha = 2.0 / (2 * readings + 1); for (ifor = 0; ifor < 250; ifor++) { // Voltage voltageSampleRead = analogRead(V) * vccRead / 1023 - vccRead / 2; /* read the sample value including offset value*/ voltageSampleSum = voltageSampleSum + sq(voltageSampleRead); /* accumulate total analog values for each sample readings*/ voltageSampleOffsetSum = voltageSampleOffsetSum + voltageSampleRead; // Current currentSampleRead = analogRead(I) * vccRead / 1023 - vccRead / 2; /* read the sample value including offset value*/ currentSampleSum = currentSampleSum + currentSampleRead * currentSampleRead; /* accumulate total analog values for each sample readings*/ currentSampleOffsetSum = currentSampleOffsetSum + currentSampleRead; wait(1); } voltageMean = voltageSampleSum / ifor; /* calculate average value of all sample readings taken*/ voltageOffset = voltageSampleOffsetSum / ifor; reading = (sqrt(voltageMean) - voltageOffset) * 230.0 / 1.0; // read voltage / reported voltage. voltage = round_to_dp(alpha * reading + (1 - alpha) * voltage,1); Serial.println(voltage); if (voltage < 25) voltage = 0; currentMean = currentSampleSum / ifor; /* calculate average value of all sample readings taken*/ currentOffset = currentSampleOffsetSum / ifor; reading = (sqrt(currentMean) - currentOffset) / SENSITIVITY * 1000 - currentZeroOffset; // subtract no load current. if (reading < 0) reading = 0; current = round_to_dp( alpha * reading + (1 - alpha) * current,2);
ESP-NOW
General Discussion • 220v i recently noticed that expres between esp8266 and es[p which allows direct conection if has released esp-now • 22 Apr 2018, 05:58 • NeverDie 17 Feb 2025, 22:24

23

0
Votes

23
Posts

6.2k
Views

17 Feb 2025, 22:24

Old topic, I know. Did anything ever come of this? I'm also thinking it would be easy & cheap to get the espnow working as a transport layer. I found this: https://www.mysensors.org/apidocs-beta/classESPNOW.html But it goes above my head and abilities when it comes to code.
Code Garage to the rescue.
General Discussion • 11 Jan 2025, 11:25 • skywatch 16 days ago

10

1
Votes

10
Posts

147
Views

16 days ago

Hi, I'm glad CodeGarage is taking over! Please are there any updates since January what's happening? The GitHub repo hasn't gotten commits for over a year. Thanks!
Email notifications received twice
General Discussion • 6 Feb 2023, 16:15 • Jodaille 27 Mar 2025, 06:07

3

1
Votes

3
Posts

39
Views

27 Mar 2025, 06:07

It looks like duplicate email notifications may be linked to system settings or preferences. Have you noticed if the issue happens after specific actions or changes? Investigating your notification settings might shed some light

0
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1