Detect Interrupt / Timer

[Dave2526]

Hello,
maybe a noob Question but i can´t find an answer:
I want to combine the Motion and the DS18B20 program. So The Temperature is sending every xx minutes, and the Motion Sensor is sending imedently. So I have to detect if the sleep is ending by the Time or The Interrupt. Is there a simple way to detect? The Code is dirty combined, i Know. I will make it better if its possible. Thanks!

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * DESCRIPTION
 *
 * Simple binary switch example 
 * Connect button or door/window reed switch between 
 * digitial I/O pin 3 (BUTTON_PIN below) and GND.
 * http://www.mysensors.org/build/binary
 */


// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
//#define MY_RADIO_NRF24
#define MY_RADIO_RFM69
//#define MY_IS_RFM69HW

#define MY_NODE_ID      200
// HW hinten dran = #define MY_IS_RFM69HW wird benötigt
// BWM WZ     101
// Test       200


#include <SPI.h>
#include <MySensors.h>
#include <DallasTemperature.h>
#include <OneWire.h>

#define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 4 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 16

#define BUTTON_PIN  3  // Arduino Digital I/O pin for button/reed switch
#define INTERRUPT BUTTON_PIN-2

int BATTERY_SENSE_PIN = A0;
unsigned long SLEEP_TIME = 600000;
//12Std = 43200000

OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
bool receivedConfig = false;
bool metric = true;
// Initialize temperature message

int oldValue=-1;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(0,V_TEMP);
MyMessage msg1(3,V_TRIPPED);

void before()
{
  // Startup up the OneWire library
  sensors.begin();
}

void setup()  
{  
  // Setup the button
  pinMode(BUTTON_PIN,INPUT);
  // Activate internal pull-down
  digitalWrite(BUTTON_PIN,LOW);

  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
  analogReference(INTERNAL);
  int sensorValue = analogRead(BATTERY_SENSE_PIN);

  analogReference(INTERNAL);

}

void presentation() {
  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  sendSketchInfo("BWM Temp", "1.0");
  present(3, S_DOOR);  

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
}
}

//  Check if digital input has changed and send in new value
void loop() 
{

  // BWM
  int value = digitalRead(BUTTON_PIN);
  send(msg1.set(value==HIGH));


  
  // Temp
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {

    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getControllerConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;

    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif

      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
      Serial.print(temperature);
    }
  }

      // get the battery Voltage
    int sensorValue = analogRead(BATTERY_SENSE_PIN);
#ifdef MY_DEBUG
    Serial.println(sensorValue);
    Serial.println(digitalRead(BUTTON_PIN));
#endif

    // 1M, 470K divider across battery and using internal ADC ref of 1.1V
    // Sense point is bypassed with 0.1 uF cap to reduce noise at that point
    // ((1e6+470e3)/470e3)*1.1 = Vmax = 3.44 Volts
    // 3.44/1023 = Volts per bit = 0.003363075

    int batteryPcnt = sensorValue *0.9375 -779.375;
    // Raum       Gain             Offset
    // Terrasse   0.9375          -779.375

#ifdef MY_DEBUG
    float batteryV  = sensorValue * 0.003363075;
    Serial.print("Battery Voltage: ");
    Serial.print(batteryV);
    Serial.println(" V");

    Serial.print("Battery percent: ");
    Serial.print(batteryPcnt);
    Serial.println(" %");
#endif

    sendBatteryLevel(batteryPcnt);

   sleep(INTERRUPT,CHANGE,SLEEP_TIME);
}

[mfalkvidd]

Welcome to the forum @Dave2526

Yes. The return value of the sleep call will let you know the reason for waking up. Documentation: https://www.mysensors.org/download/sensor_api_20#sleeping

[Dave2526]

Thats what I think, a really simple thing, Thank You, it works!

resp_sleep=sleep(INTERRUPT,CHANGE,SLEEP_TIME);

and then hust a simple if resp_sleep....

Thanks!