Node-Red as Controller
Node-RED
54
Posts
17
Posters
48.1k
Views
19
Watching
-
Hello
I have been tinkering a little with this and it does actually work.
The only thing is that you must point the topic of the mqtt node directly to a child. Its not possible to just subscribe to topics higher in the hierarchy.For example in MyMQTT app on Android i can just subscribe to topic MyMQTT and then i get messages from all nodes connected to the Gateway. This is not possible with the mqtt node in NodeRED. You must specifically point it.
below is and example of an mqtt node outputting to a debug node. My Gateway is at 192.168.1.201.[{"id":"d0ff7866.2f0088","type":"mqtt-broker","broker":"192.168.1.201","port":"1883","clientid":"MQTT"},{"id":"14e0544d.eb1fac","type":"debug","name":"","active":true,"console":"false","complete":"false","x":304,"y":827,"z":"cda8f31c.32571","wires":[]},{"id":"8792e08c.786d2","type":"mqtt in","name":"Temperatur","topic":"MyMQTT/21/1/V_TEMP","broker":"d0ff7866.2f0088","x":67.5,"y":791,"z":"cda8f31c.32571","wires":[["14e0544d.eb1fac"]]}]I am working on some code to push temperatures as an object trough a websocket for live viewing on a simple webpage.
It maybe sounds advanced, but it is actually very easy. In my opinion Node-RED is just as powerfull as OpenHAB and not particulary more advanced either. Will post a full working example when i have everything ready.@Fredrik-Carlsson said:
The only thing is that you must point the topic of the mqtt node directly to a child. Its not possible to just subscribe to topics higher in the hierarchy.
For example in MyMQTT app on Android i can just subscribe to topic MyMQTT and then i get messages from all nodes connected to the Gateway. This is not possible with the mqtt node in NodeRED. You must specifically point it.
You can capture all higher level topics by using the # symbal. As I mention above, my openHAB sents RF24SN/out/.... and on node-red I have an mqtt node that listens for RF24SN/out/#.
Mike
-
@Fredrik-Carlsson said:
The only thing is that you must point the topic of the mqtt node directly to a child. Its not possible to just subscribe to topics higher in the hierarchy.
For example in MyMQTT app on Android i can just subscribe to topic MyMQTT and then i get messages from all nodes connected to the Gateway. This is not possible with the mqtt node in NodeRED. You must specifically point it.
You can capture all higher level topics by using the # symbal. As I mention above, my openHAB sents RF24SN/out/.... and on node-red I have an mqtt node that listens for RF24SN/out/#.
Mike
@Mike-Cayouette thanks, I will try that tomorrow!
-
Here is my setup:
- MyMQTT Client Gateway, OpenHAB, HomeMatic and node-red all connected to mosquitto
- OpenHab configured to expose the internal bus to mosquitto
- All glued together with node-red: the OpenHab Items have no mqtt binding, all messages are exchanged via the OpenHab internal bus.
- Messages from any sensors are transformed in node-red to the destination (topic and payload)
The advantage of this setup is:
- OpenHab is only the GUI and doesn't need to know anything about the sensors
- I can exchange any sensor/actuator without any change in OpenHab. I can even change from a netatmo device to a mysensor device or vice versa.
I was thinking about replacing the MyMQTT Client Gateway with a Serial Gateway and node-red, but the gateway is stable since weeks.... never touch a running system. This would solve my biggest concern with the MyMQTT Client Gateway: it doesn't support encryption....
-
The following node-red sample illustrates how the data sent by the serial gateway can be analysed.
The upper lane receives the data from COM-Port, splits the incomming message into single tokens and feeds the result into
a switch block.
The lower lane implements a http request which displays data for message type "set".
The result of this simple sniffer looks like:
On the top right I added a debug node to visualize the incomming data:
This should be a minimalistic sample to get a feeling for how much work it would take to implement a fully functional controller.
If the "presentation" messages would be fed into some no-sql database like mongoose, answering nodeid-requests shouldn't be a challenging task. In the end I think this could be done in 1-2 days. -
if anybody wants to try it on his own here is the source which can be imported into node-red.
[{"id":"e2627000.52f61","type":"serial-port","serialport":"COM13","serialbaud":"115200","databits":"8","parity":"none","stopbits":"1","newline":"10","bin":"false","out":"time","addchar":true},{"id":"ae116278.ceadf","type":"serial in","name":"SerialGateway","serial":"e2627000.52f61","x":75.5,"y":170.3333511352539,"z":"6e87bdcb.1ab8d4","wires":[["421469f9.a974f8"]]},{"id":"421469f9.a974f8","type":"function","name":"split message","func":"var message = msg.payload;\nsplitMessage = message.split(\" \");\nif(splitMessage[0] == \"0;0;3;0;9;read:\")\n{\n msg.route = splitMessage[1].split(\"-\");\n \n var splitData = splitMessage[2].split(\"\\n\");\n var tokens = splitData[1].split(\";\")\n \n msg.rawData = tokens;\n if(tokens.length == 6)\n {\n msg.nodeId = tokens[0];\n msg.childSensorId = tokens[1];\n msg.messageType = tokens[2];\n msg.ack = tokens[3];\n msg.subType = tokens[4];\n msg.payload = tokens[5];\n }\n}\nelse\n{\n \n}\nreturn msg;","outputs":1,"valid":true,"x":260.5,"y":170.3333511352539,"z":"6e87bdcb.1ab8d4","wires":[["ea996599.33b75"]]},{"id":"ea996599.33b75","type":"switch","name":"switch message type","property":"messageType","rules":[{"t":"eq","v":"0"},{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"true","outputs":5,"x":461.49998474121094,"y":170.3333511352539,"z":"6e87bdcb.1ab8d4","wires":[["4bca8505.d463e4"],["cfb87963.3e2a8"],["7cd01fb.f71436"],["e722ad62.22ebd"],["9f4ff922.f54838"]]},{"id":"4bca8505.d463e4","type":"function","name":"presentation","func":"msg.topic = \"presentation\";\nreturn msg;","outputs":1,"valid":true,"x":681.5,"y":37.333335876464844,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"7cd01fb.f71436","type":"function","name":"req","func":"msg.topic = \"req\";\nreturn msg;","outputs":1,"valid":true,"x":698.3333129882812,"y":152.33334350585938,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"e722ad62.22ebd","type":"function","name":"internal","func":"msg.topic = \"internal\";\nreturn msg;","outputs":1,"valid":true,"x":693.3333129882812,"y":203.33334350585938,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"9f4ff922.f54838","type":"function","name":"stream","func":"msg.topic = \"stream\";\nreturn msg;","outputs":1,"valid":true,"x":692.3333129882812,"y":261.3333435058594,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"137f8a82.b7ce45","type":"debug","name":"debug","active":true,"console":"false","complete":"true","x":897.3333129882812,"y":101.33333587646484,"z":"6e87bdcb.1ab8d4","wires":[]},{"id":"ff056cd7.417e98","type":"http response","name":"http out","x":744,"y":444.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[]},{"id":"74b70760.4f808","type":"http in","name":"","url":"/mysensorsdata","method":"get","x":151.00001525878906,"y":444.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[["68713a54.5c30ec"]]},{"id":"e26e1fbf.606c8","type":"template","name":"html template","field":"","format":"html","template":"\nGateway <br />\nreceived at: {{data.timestamp}}<br />\nnode-id: {{data.nodeId}}<br />\nchild-SensorId: {{data.childSensorId}}<br />\nmessageType: {{data.messageType}}<br />\nsubType: {{data.subType}}<br />\npayload: {{data.payload}}\n","x":560.0000152587891,"y":445.33336663246155,"z":"6e87bdcb.1ab8d4","wires":[["ff056cd7.417e98"]]},{"id":"68713a54.5c30ec","type":"function","name":"message buffer","func":"context.data = context.data || new Object();\n\nswitch (msg.topic) {\n case \"set\":\n context.data.timestamp = new Date().toLocaleString();\n context.data.nodeId = msg.nodeId;\n context.data.childSensorId = msg.childSensorId;\n context.data.messageType = msg.messageType;\n context.data.subType = msg.subType;\n context.data.payload = msg.payload;\n msg = null;\n break;\n default:\n \tmsg.data = context.data;\n}\n\nreturn msg;","outputs":1,"valid":true,"x":393.00001525878906,"y":445.3333435058594,"z":"6e87bdcb.1ab8d4","wires":[["e26e1fbf.606c8"]]},{"id":"8f3083f8.2dc96","type":"http in","name":"","url":"/mysensors","method":"get","x":135.00001525878906,"y":507.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[["92f9be8f.e42c68"]]},{"id":"92f9be8f.e42c68","type":"template","name":"Auto Update Script","field":"","template":"<script>\n setInterval(function(){\t\n\t var theUrl = \"http://localhost:1880/mysensorsdata\";\n\t var xmlHttp = new XMLHttpRequest();\n\t xmlHttp.open( \"GET\", theUrl, false );\n\t xmlHttp.send( null );\n\t document. getElementById('mysensorsdata')\n\t \t.innerHTML = xmlHttp.responseText;\n },1000);\n</script>\n<div id = 'mysensorsdata'>\n ... Loading ...\n</div>\n","x":410,"y":507.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[["ff056cd7.417e98"]]},{"id":"cfb87963.3e2a8","type":"function","name":"set","func":"msg.topic = \"set\";\nreturn msg;","outputs":1,"valid":true,"x":696.5,"y":101.33333587646484,"z":"6e87bdcb.1ab8d4","wires":[["137f8a82.b7ce45","68713a54.5c30ec"]]}] -
if anybody wants to try it on his own here is the source which can be imported into node-red.
[{"id":"e2627000.52f61","type":"serial-port","serialport":"COM13","serialbaud":"115200","databits":"8","parity":"none","stopbits":"1","newline":"10","bin":"false","out":"time","addchar":true},{"id":"ae116278.ceadf","type":"serial in","name":"SerialGateway","serial":"e2627000.52f61","x":75.5,"y":170.3333511352539,"z":"6e87bdcb.1ab8d4","wires":[["421469f9.a974f8"]]},{"id":"421469f9.a974f8","type":"function","name":"split message","func":"var message = msg.payload;\nsplitMessage = message.split(\" \");\nif(splitMessage[0] == \"0;0;3;0;9;read:\")\n{\n msg.route = splitMessage[1].split(\"-\");\n \n var splitData = splitMessage[2].split(\"\\n\");\n var tokens = splitData[1].split(\";\")\n \n msg.rawData = tokens;\n if(tokens.length == 6)\n {\n msg.nodeId = tokens[0];\n msg.childSensorId = tokens[1];\n msg.messageType = tokens[2];\n msg.ack = tokens[3];\n msg.subType = tokens[4];\n msg.payload = tokens[5];\n }\n}\nelse\n{\n \n}\nreturn msg;","outputs":1,"valid":true,"x":260.5,"y":170.3333511352539,"z":"6e87bdcb.1ab8d4","wires":[["ea996599.33b75"]]},{"id":"ea996599.33b75","type":"switch","name":"switch message type","property":"messageType","rules":[{"t":"eq","v":"0"},{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"true","outputs":5,"x":461.49998474121094,"y":170.3333511352539,"z":"6e87bdcb.1ab8d4","wires":[["4bca8505.d463e4"],["cfb87963.3e2a8"],["7cd01fb.f71436"],["e722ad62.22ebd"],["9f4ff922.f54838"]]},{"id":"4bca8505.d463e4","type":"function","name":"presentation","func":"msg.topic = \"presentation\";\nreturn msg;","outputs":1,"valid":true,"x":681.5,"y":37.333335876464844,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"7cd01fb.f71436","type":"function","name":"req","func":"msg.topic = \"req\";\nreturn msg;","outputs":1,"valid":true,"x":698.3333129882812,"y":152.33334350585938,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"e722ad62.22ebd","type":"function","name":"internal","func":"msg.topic = \"internal\";\nreturn msg;","outputs":1,"valid":true,"x":693.3333129882812,"y":203.33334350585938,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"9f4ff922.f54838","type":"function","name":"stream","func":"msg.topic = \"stream\";\nreturn msg;","outputs":1,"valid":true,"x":692.3333129882812,"y":261.3333435058594,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"137f8a82.b7ce45","type":"debug","name":"debug","active":true,"console":"false","complete":"true","x":897.3333129882812,"y":101.33333587646484,"z":"6e87bdcb.1ab8d4","wires":[]},{"id":"ff056cd7.417e98","type":"http response","name":"http out","x":744,"y":444.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[]},{"id":"74b70760.4f808","type":"http in","name":"","url":"/mysensorsdata","method":"get","x":151.00001525878906,"y":444.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[["68713a54.5c30ec"]]},{"id":"e26e1fbf.606c8","type":"template","name":"html template","field":"","format":"html","template":"\nGateway <br />\nreceived at: {{data.timestamp}}<br />\nnode-id: {{data.nodeId}}<br />\nchild-SensorId: {{data.childSensorId}}<br />\nmessageType: {{data.messageType}}<br />\nsubType: {{data.subType}}<br />\npayload: {{data.payload}}\n","x":560.0000152587891,"y":445.33336663246155,"z":"6e87bdcb.1ab8d4","wires":[["ff056cd7.417e98"]]},{"id":"68713a54.5c30ec","type":"function","name":"message buffer","func":"context.data = context.data || new Object();\n\nswitch (msg.topic) {\n case \"set\":\n context.data.timestamp = new Date().toLocaleString();\n context.data.nodeId = msg.nodeId;\n context.data.childSensorId = msg.childSensorId;\n context.data.messageType = msg.messageType;\n context.data.subType = msg.subType;\n context.data.payload = msg.payload;\n msg = null;\n break;\n default:\n \tmsg.data = context.data;\n}\n\nreturn msg;","outputs":1,"valid":true,"x":393.00001525878906,"y":445.3333435058594,"z":"6e87bdcb.1ab8d4","wires":[["e26e1fbf.606c8"]]},{"id":"8f3083f8.2dc96","type":"http in","name":"","url":"/mysensors","method":"get","x":135.00001525878906,"y":507.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[["92f9be8f.e42c68"]]},{"id":"92f9be8f.e42c68","type":"template","name":"Auto Update Script","field":"","template":"<script>\n setInterval(function(){\t\n\t var theUrl = \"http://localhost:1880/mysensorsdata\";\n\t var xmlHttp = new XMLHttpRequest();\n\t xmlHttp.open( \"GET\", theUrl, false );\n\t xmlHttp.send( null );\n\t document. getElementById('mysensorsdata')\n\t \t.innerHTML = xmlHttp.responseText;\n },1000);\n</script>\n<div id = 'mysensorsdata'>\n ... Loading ...\n</div>\n","x":410,"y":507.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[["ff056cd7.417e98"]]},{"id":"cfb87963.3e2a8","type":"function","name":"set","func":"msg.topic = \"set\";\nreturn msg;","outputs":1,"valid":true,"x":696.5,"y":101.33333587646484,"z":"6e87bdcb.1ab8d4","wires":[["137f8a82.b7ce45","68713a54.5c30ec"]]}]where are you storing the sensor data for presentation , stream. let me know which database you are using here? you can have another flows for sending the the request to sensor node via serial port. I tried it same some time back . may be i can share it here. :smiley:
-
if anybody wants to try it on his own here is the source which can be imported into node-red.
[{"id":"e2627000.52f61","type":"serial-port","serialport":"COM13","serialbaud":"115200","databits":"8","parity":"none","stopbits":"1","newline":"10","bin":"false","out":"time","addchar":true},{"id":"ae116278.ceadf","type":"serial in","name":"SerialGateway","serial":"e2627000.52f61","x":75.5,"y":170.3333511352539,"z":"6e87bdcb.1ab8d4","wires":[["421469f9.a974f8"]]},{"id":"421469f9.a974f8","type":"function","name":"split message","func":"var message = msg.payload;\nsplitMessage = message.split(\" \");\nif(splitMessage[0] == \"0;0;3;0;9;read:\")\n{\n msg.route = splitMessage[1].split(\"-\");\n \n var splitData = splitMessage[2].split(\"\\n\");\n var tokens = splitData[1].split(\";\")\n \n msg.rawData = tokens;\n if(tokens.length == 6)\n {\n msg.nodeId = tokens[0];\n msg.childSensorId = tokens[1];\n msg.messageType = tokens[2];\n msg.ack = tokens[3];\n msg.subType = tokens[4];\n msg.payload = tokens[5];\n }\n}\nelse\n{\n \n}\nreturn msg;","outputs":1,"valid":true,"x":260.5,"y":170.3333511352539,"z":"6e87bdcb.1ab8d4","wires":[["ea996599.33b75"]]},{"id":"ea996599.33b75","type":"switch","name":"switch message type","property":"messageType","rules":[{"t":"eq","v":"0"},{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"true","outputs":5,"x":461.49998474121094,"y":170.3333511352539,"z":"6e87bdcb.1ab8d4","wires":[["4bca8505.d463e4"],["cfb87963.3e2a8"],["7cd01fb.f71436"],["e722ad62.22ebd"],["9f4ff922.f54838"]]},{"id":"4bca8505.d463e4","type":"function","name":"presentation","func":"msg.topic = \"presentation\";\nreturn msg;","outputs":1,"valid":true,"x":681.5,"y":37.333335876464844,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"7cd01fb.f71436","type":"function","name":"req","func":"msg.topic = \"req\";\nreturn msg;","outputs":1,"valid":true,"x":698.3333129882812,"y":152.33334350585938,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"e722ad62.22ebd","type":"function","name":"internal","func":"msg.topic = \"internal\";\nreturn msg;","outputs":1,"valid":true,"x":693.3333129882812,"y":203.33334350585938,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"9f4ff922.f54838","type":"function","name":"stream","func":"msg.topic = \"stream\";\nreturn msg;","outputs":1,"valid":true,"x":692.3333129882812,"y":261.3333435058594,"z":"6e87bdcb.1ab8d4","wires":[[]]},{"id":"137f8a82.b7ce45","type":"debug","name":"debug","active":true,"console":"false","complete":"true","x":897.3333129882812,"y":101.33333587646484,"z":"6e87bdcb.1ab8d4","wires":[]},{"id":"ff056cd7.417e98","type":"http response","name":"http out","x":744,"y":444.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[]},{"id":"74b70760.4f808","type":"http in","name":"","url":"/mysensorsdata","method":"get","x":151.00001525878906,"y":444.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[["68713a54.5c30ec"]]},{"id":"e26e1fbf.606c8","type":"template","name":"html template","field":"","format":"html","template":"\nGateway <br />\nreceived at: {{data.timestamp}}<br />\nnode-id: {{data.nodeId}}<br />\nchild-SensorId: {{data.childSensorId}}<br />\nmessageType: {{data.messageType}}<br />\nsubType: {{data.subType}}<br />\npayload: {{data.payload}}\n","x":560.0000152587891,"y":445.33336663246155,"z":"6e87bdcb.1ab8d4","wires":[["ff056cd7.417e98"]]},{"id":"68713a54.5c30ec","type":"function","name":"message buffer","func":"context.data = context.data || new Object();\n\nswitch (msg.topic) {\n case \"set\":\n context.data.timestamp = new Date().toLocaleString();\n context.data.nodeId = msg.nodeId;\n context.data.childSensorId = msg.childSensorId;\n context.data.messageType = msg.messageType;\n context.data.subType = msg.subType;\n context.data.payload = msg.payload;\n msg = null;\n break;\n default:\n \tmsg.data = context.data;\n}\n\nreturn msg;","outputs":1,"valid":true,"x":393.00001525878906,"y":445.3333435058594,"z":"6e87bdcb.1ab8d4","wires":[["e26e1fbf.606c8"]]},{"id":"8f3083f8.2dc96","type":"http in","name":"","url":"/mysensors","method":"get","x":135.00001525878906,"y":507.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[["92f9be8f.e42c68"]]},{"id":"92f9be8f.e42c68","type":"template","name":"Auto Update Script","field":"","template":"<script>\n setInterval(function(){\t\n\t var theUrl = \"http://localhost:1880/mysensorsdata\";\n\t var xmlHttp = new XMLHttpRequest();\n\t xmlHttp.open( \"GET\", theUrl, false );\n\t xmlHttp.send( null );\n\t document. getElementById('mysensorsdata')\n\t \t.innerHTML = xmlHttp.responseText;\n },1000);\n</script>\n<div id = 'mysensorsdata'>\n ... Loading ...\n</div>\n","x":410,"y":507.3333740234375,"z":"6e87bdcb.1ab8d4","wires":[["ff056cd7.417e98"]]},{"id":"cfb87963.3e2a8","type":"function","name":"set","func":"msg.topic = \"set\";\nreturn msg;","outputs":1,"valid":true,"x":696.5,"y":101.33333587646484,"z":"6e87bdcb.1ab8d4","wires":[["137f8a82.b7ce45","68713a54.5c30ec"]]}]@Heinz ,
Thanks for the flow. kindly post how you have referenced mysensors library for the flow? Split function is spitting out an error as is.
OR Is it required at all?Function Error: TypeError: Cannot call method 'split' of undefined (line 8, col 31)
-
-
where are you storing the sensor data for presentation , stream. let me know which database you are using here? you can have another flows for sending the the request to sensor node via serial port. I tried it same some time back . may be i can share it here. :smiley:
@Dheeraj said:
where are you storing the sensor data for presentation , stream. let me know which database you are using here? you can have another flows for sending the the request to sensor node via serial port. I tried it same some time back . may be i can share it here. :smiley:
@Dheeraj, Will you like to share your way out here?
-
I paused the project as I am working on my low power sensors. As soon as I continue I will post it here.
-
@Heinz ,
Thanks for the flow. kindly post how you have referenced mysensors library for the flow? Split function is spitting out an error as is.
OR Is it required at all?Function Error: TypeError: Cannot call method 'split' of undefined (line 8, col 31)
@vikasjee said:
Function Error: TypeError: Cannot call method 'split' of undefined (line 8, col 31)
You need to add an commit to the line 8 like
var tokens = splitData[1].split(";");I'm getting data at : http://192.168.1.115:1880/mysensorsdata, but the http://192.168.1.115:1880/mysensors don't update.. there is an autoupdate in the flow but it don't work..
-
which browser did you take? Probably you should try another one.
-
I've used NodeRED for various tasks over the years and it still remains my favorite IOT interface. All the while I've tried at least 5 of the officially supported MS controllers out there and nothing has come close! At present I'm trying Home Assistant but am almost ready to give up and set up my own workflow with NodeRED. There's a blog post at https://crankylinuxuser.net/2015/10/01/idiot-crazy-ways-to-make-iot-simple-and-cheap/ that includes a great example of a MySensors+NodeRED flow along with a spot-on critique of mainstream automation services being marketed at present.
The only reason I havent just used NodeRED in the past is it would still require other components to truly make a unified home automation service. An ideal scenario IMHO would be something that uses NodeRED as a front-end with something more unified running it.
-
Here my approach:
[{"id":"ba386057.845d3","type":"mqtt-broker","broker":"192.168.92.4","port":"1883","clientid":"NodeRed"},{"id":"b5e4f17d.4a1b1","type":"function","name":"hanlde internal messages","func":"//msg.subTypeString = \"\";\n//msg.topic = \"internal respones\";\n\nif (msg.subTypeString == 'I_TIME')\n{\n var payload = parseInt(new Date().getTime()/1000);\n\tvar command = context.global.MYS.T_INTERNAL; \n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_TIME; // I_TIME\n\tmsg.payload = encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg;\n \n}\nelse if (msg.subTypeString == 'I_ID_REQUEST')\n{\n msg.topic = \"I_ID_RESPONSE\";\n msg.subTypeString = \"I_ID_RESPONSE\";\n // 255;255;3;0;4;8 for ID 8\n var command = context.global.MYS.T_INTERNAL;\n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_ID_RESPONSE; // I_ID_RESPONSE\n\n\tif (context.global.mysnextid[msg.controller] === undefined) {\n\t payload = context.global.MYS.MIN_NODEID;\n\t} \n\telse\n\t{\n\t payload = context.global.mysnextid[msg.controller];\n\t}\n\t\n msg.payload = encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg; \n} \nelse if (msg.subTypeString == 'I_INCLUSION_MODE')\n{\n // not yet implemented\n}\n\nreturn;\n\nfunction encode(destination, sensor, command, acknowledge, type, payload) {\n\tvar msg = destination.toString(10) + \";\" + sensor.toString(10) + \";\" + command.toString(10) + \";\" + acknowledge.toString(10) + \";\" + type.toString(10) + \";\";\n\tif (command == 4) {\n\t\tfor (var i = 0; i < payload.length; i++) {\n\t\t\tif (payload[i] < 16)\n\t\t\t\tmsg += \"0\";\n\t\t\tmsg += payload[i].toString(16);\n\t\t}\n\t} else {\n\t\tmsg += payload;\n\t}\n\tmsg += '\\n';\n\treturn msg.toString();\n}\n","outputs":1,"noerr":0,"x":1655.916648864746,"y":536.4166927337646,"z":"9592163f.6a6de8","wires":[["4d15a037.b2ea6","266b87b3.d99478"]]},{"id":"e6ce260d.1931d8","type":"switch","name":"switch message type","property":"messageType","rules":[{"t":"eq","v":"0"},{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"true","outputs":5,"x":1220.166648864746,"y":175.5000171661377,"z":"9592163f.6a6de8","wires":[["8c663d73.7399c"],["4a1e5f84.b5e1a"],["7753f9a2.88ac08"],["1e4aa61b.e1b55a"],["60a0dde4.9f5f24"]]},{"id":"8c663d73.7399c","type":"function","name":"presentation","func":"msg.subTypeString = context.global.MYS.SString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1449.916648864746,"y":38.2499885559082,"z":"9592163f.6a6de8","wires":[["df9e131d.2061f","4d15a037.b2ea6"]]},{"id":"7753f9a2.88ac08","type":"function","name":"req","func":"msg.topic = \"req\";\nreturn msg;","outputs":1,"noerr":0,"x":1445.5000228881836,"y":175.7500057220459,"z":"9592163f.6a6de8","wires":[["4d15a037.b2ea6"]]},{"id":"1e4aa61b.e1b55a","type":"function","name":"internal","func":"msg.subTypeString = context.global.MYS.IString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1449.5000228881836,"y":226.0000057220459,"z":"9592163f.6a6de8","wires":[["df9e131d.2061f","4d15a037.b2ea6","b5e4f17d.4a1b1"]]},{"id":"60a0dde4.9f5f24","type":"function","name":"stream","func":"msg.topic = \"stream\";\nreturn msg;","outputs":1,"x":1457.5000228881836,"y":321.0000057220459,"z":"9592163f.6a6de8","wires":[[]]},{"id":"4d15a037.b2ea6","type":"debug","name":"debug","active":true,"console":"false","complete":"true","x":1806.7500267028809,"y":235.00000667572021,"z":"9592163f.6a6de8","wires":[]},{"id":"4a1e5f84.b5e1a","type":"function","name":"set","func":"msg.subTypeString = context.global.MYS.VString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\n\nreturn msg;","outputs":1,"noerr":0,"x":1453.166648864746,"y":100.50000381469727,"z":"9592163f.6a6de8","wires":[["4d15a037.b2ea6","df9e131d.2061f"]]},{"id":"fc54bb91.03ab48","type":"debug","name":"","active":false,"console":"false","complete":"true","x":1179.9166259765625,"y":34.66668891906738,"z":"9592163f.6a6de8","wires":[]},{"id":"6aa2d9f6.955d28","type":"function","name":"Split GW Message","func":"\n var tokens = msg.payload.split(\";\")\n \n msg.rawData = tokens;\n if(tokens.length >= 6)\n {\n msg.nodeId = tokens[0];\n msg.childSensorId = tokens[1];\n msg.messageType = tokens[2];\n msg.ack = tokens[3];\n msg.subType = tokens[4];\n msg.payload = tokens[5];\n for (j=6; j<tokens.length; j++) \n msg.payload = msg.payload + ';' + tokens[j];\n }\n\nreturn msg;","outputs":1,"noerr":0,"x":984.6666488647461,"y":173.66664505004883,"z":"9592163f.6a6de8","wires":[["e6ce260d.1931d8","fc54bb91.03ab48","e0e76d62.1f189"]]},{"id":"df9e131d.2061f","type":"mqtt out","name":"Publish to MQTT","topic":"","qos":"","retain":"","broker":"ba386057.845d3","x":1819.9166526794434,"y":174.1666603088379,"z":"9592163f.6a6de8","wires":[]},{"id":"5f03c10e.a0fc4","type":"tcp request","server":"192.168.92.13","port":"5003","out":"char","splitc":"\\n","name":"MySWifi ESP8266 GW AES 13","x":376.6666946411133,"y":140.1666316986084,"z":"9592163f.6a6de8","wires":[["df1e322.f20e1d"]]},{"id":"e6d67f33.19298","type":"inject","name":"Startup","topic":"","payload":"","payloadType":"none","repeat":"","crontab":"","once":true,"x":106.25,"y":74.41665744781494,"z":"9592163f.6a6de8","wires":[["5f03c10e.a0fc4","64617800.9b9e88","c7d0d88b.382f28","56b9f6ab.a94608"]]},{"id":"ebcef3df.14311","type":"function","name":"ToString","func":"msg.payload = msg.payload.toString().replace(/[\\n\\r]/g, '');\n\nreturn msg;","outputs":1,"noerr":0,"x":790.1666946411133,"y":174.91669178009033,"z":"9592163f.6a6de8","wires":[["6aa2d9f6.955d28"]]},{"id":"31047fa6.cefb8","type":"catch","name":"","x":71,"y":642,"z":"9592163f.6a6de8","wires":[["3622f9b9.c9dd06"]]},{"id":"3622f9b9.c9dd06","type":"debug","name":"","active":false,"console":"false","complete":"true","x":216,"y":642,"z":"9592163f.6a6de8","wires":[]},{"id":"64617800.9b9e88","type":"function","name":"MYS Initialize","func":"function MySHelper() { \n\nMySHelper.prototype.TOPIC_PREFIX = \"MYS-NODERED\";\n\nMySHelper.prototype.MIN_NODEID = 10;\n\n\n// don't touch below :)\n \nMySHelper.prototype.T_PRESENTATION = 0;\nMySHelper.prototype.T_SET = 1;\nMySHelper.prototype.T_REQ = 2;\nMySHelper.prototype.T_INTERNAL = 3;\nMySHelper.prototype.T_STREAM = 4;\n\nMySHelper.prototype.I_BATTERY_LEVEL = 0;\nMySHelper.prototype.I_TIME = 1;\nMySHelper.prototype.I_VERSION = 2;\nMySHelper.prototype.I_ID_REQUEST = 3;\nMySHelper.prototype.I_ID_RESPONSE = 4;\nMySHelper.prototype.I_INCLUSION_MODE = 5;\nMySHelper.prototype.I_CONFIG = 6;\nMySHelper.prototype.I_PING = 7;\nMySHelper.prototype.I_PING_ACK = 8;\nMySHelper.prototype.I_LOG_MESSAGE = 9;\nMySHelper.prototype.I_CHILDREN = 10;\nMySHelper.prototype.I_SKETCH_NAME = 11;\nMySHelper.prototype.I_SKETCH_VERSION = 12;\nMySHelper.prototype.I_REBOOT = 13;\nMySHelper.prototype.I_GATEWAY_READY = 14;\nMySHelper.prototype.I_REQUEST_SIGNING = 15;\nMySHelper.prototype.I_GET_NONCE = 16;\nMySHelper.prototype.I_GET_NONCE_RESPONSE = 17;\nMySHelper.prototype.I_HEARTBEAT = 18;\nMySHelper.prototype.I_PRESENTATION = 19;\n \nvar itype = {\nI_BATTERY_LEVEL: MySHelper.prototype.I_BATTERY_LEVEL,\nI_TIME: MySHelper.prototype.I_TIME,\nI_VERSION: MySHelper.prototype.I_VERSION,\nI_ID_REQUEST: MySHelper.prototype.I_ID_REQUEST,\nI_ID_RESPONSE: MySHelper.prototype.I_ID_RESPONSE,\nI_INCLUSION_MODE: MySHelper.prototype.I_INCLUSION_MODE,\nI_CONFIG: MySHelper.prototype.I_CONFIG,\nI_PING: MySHelper.prototype.I_PING,\nI_PING_ACK: MySHelper.prototype.I_PING_ACK,\nI_LOG_MESSAGE: MySHelper.prototype.I_LOG_MESSAGE,\nI_CHILDREN: MySHelper.prototype.I_CHILDREN,\nI_SKETCH_NAME: MySHelper.prototype.I_SKETCH_NAME,\nI_SKETCH_VERSION: MySHelper.prototype.I_SKETCH_VERSION,\nI_REBOOT: MySHelper.prototype.I_REBOOT,\nI_GATEWAY_READY: MySHelper.prototype.I_GATEWAY_READY,\nI_REQUEST_SIGNING: MySHelper.prototype.I_REQUEST_SIGNING,\nI_GET_NONCE: MySHelper.prototype.I_GET_NONCE,\nI_GET_NONCE_RESPONSE: MySHelper.prototype.I_GET_NONCE_RESPONSE,\nI_HEARTBEAT: MySHelper.prototype.I_HEARTBEAT,\nI_PRESENTATION: MySHelper.prototype.I_PRESENTATION\n};\n\nMySHelper.prototype.IString = function(I_SUBTYPE) {\n for (var prop in itype ) \n if( itype[ prop ] === parseInt(I_SUBTYPE) )\n return prop;\n};\n\nMySHelper.prototype.V_TEMP = 0;\nMySHelper.prototype.V_HUM = 1;\nMySHelper.prototype.V_LIGHT = 2;\nMySHelper.prototype.V_DIMMER = 3;\nMySHelper.prototype.V_PRESSURE = 4;\nMySHelper.prototype.V_FORECAST = 5;\nMySHelper.prototype.V_RAIN = 6;\nMySHelper.prototype.V_RAINRATE = 7;\nMySHelper.prototype.V_WIND = 8;\nMySHelper.prototype.V_GUST = 9;\nMySHelper.prototype.V_DIRECTION = 10;\nMySHelper.prototype.V_UV = 11;\nMySHelper.prototype.V_WEIGHT = 12;\nMySHelper.prototype.V_DISTANCE = 13;\nMySHelper.prototype.V_IMPEDANCE = 14;\nMySHelper.prototype.V_ARMED = 15;\nMySHelper.prototype.V_TRIPPED = 16;\nMySHelper.prototype.V_WATT = 17;\nMySHelper.prototype.V_KWH = 18;\nMySHelper.prototype.V_SCENE_ON = 19;\nMySHelper.prototype.V_SCENE_OFF = 20;\nMySHelper.prototype.V_HEATER = 21;\nMySHelper.prototype.V_HEATER_SW = 22;\nMySHelper.prototype.V_LIGHT_LEVEL = 23;\nMySHelper.prototype.V_VAR1 = 24;\nMySHelper.prototype.V_VAR2 = 25;\nMySHelper.prototype.V_VAR3 = 26;\nMySHelper.prototype.V_VAR4 = 27;\nMySHelper.prototype.V_VAR5 = 28;\nMySHelper.prototype.V_UP = 29;\nMySHelper.prototype.V_DOWN = 30;\nMySHelper.prototype.V_STOP = 31;\nMySHelper.prototype.V_IR_SEND = 32;\nMySHelper.prototype.V_IR_RECEIVE = 33;\nMySHelper.prototype.V_FLOW = 34;\nMySHelper.prototype.V_VOLUME = 35;\nMySHelper.prototype.V_LOCK_STATUS = 36;\nMySHelper.prototype.V_LEVEL = 37; \nMySHelper.prototype.V_VOLTAGE = 38; \nMySHelper.prototype.V_CURRENT = 39; \nMySHelper.prototype.V_RGB = 40; \nMySHelper.prototype.V_RGBW = 41;\nMySHelper.prototype.V_ID = 42;\nMySHelper.prototype.V_UNIT_PREFIX = 43;\nMySHelper.prototype.V_HVAC_SETPOINT_COOL = 44;\nMySHelper.prototype.V_HVAC_SETPOINT_HEAT = 45;\nMySHelper.prototype.V_HVAC_FLOW_MODE = 46;\nMySHelper.prototype.V_TEXT = 47;\n\nvar vtype = {\nV_TEMP: MySHelper.prototype.V_TEMP,\nV_HUM: MySHelper.prototype.V_HUM,\nV_LIGHT: MySHelper.prototype.V_LIGHT,\nV_DIMMER: MySHelper.prototype.V_DIMMER,\nV_PRESSURE: MySHelper.prototype.V_PRESSURE,\nV_FORECAST: MySHelper.prototype.V_FORECAST,\nV_RAIN: MySHelper.prototype.V_RAIN,\nV_RAINRATE: MySHelper.prototype.V_RAINRATE,\nV_WIND: MySHelper.prototype.V_WIND,\nV_GUST: MySHelper.prototype.V_GUST,\nV_DIRECTION: MySHelper.prototype.V_DIRECTION,\nV_UV: MySHelper.prototype.V_UV,\nV_WEIGHT: MySHelper.prototype.V_WEIGHT,\nV_DISTANCE: MySHelper.prototype.V_DISTANCE,\nV_IMPEDANCE: MySHelper.prototype.V_IMPEDANCE,\nV_ARMED: MySHelper.prototype.V_ARMED,\nV_TRIPPED: MySHelper.prototype.V_TRIPPED,\nV_WATT: MySHelper.prototype.V_WATT,\nV_KWH: MySHelper.prototype.V_KWH,\nV_SCENE_ON: MySHelper.prototype.V_SCENE_ON,\nV_SCENE_OFF: MySHelper.prototype.V_SCENE_OFF,\nV_HEATER: MySHelper.prototype.V_HEATER,\nV_HEATER_SW: MySHelper.prototype.V_HEATER_SW,\nV_LIGHT_LEVEL: MySHelper.prototype.V_LIGHT_LEVEL,\nV_VAR1: MySHelper.prototype.V_VAR1,\nV_VAR2: MySHelper.prototype.V_VAR2,\nV_VAR3: MySHelper.prototype.V_VAR3,\nV_VAR4: MySHelper.prototype.V_VAR4,\nV_VAR5: MySHelper.prototype.V_VAR5,\nV_UP: MySHelper.prototype.V_UP,\nV_DOWN: MySHelper.prototype.V_DOWN,\nV_STOP: MySHelper.prototype.V_STOP,\nV_IR_SEND: MySHelper.prototype.V_IR_SEND,\nV_IR_RECEIVE: MySHelper.prototype.V_IR_RECEIVE,\nV_FLOW: MySHelper.prototype.V_FLOW,\nV_VOLUME: MySHelper.prototype.V_VOLUME,\nV_LOCK_STATUS: MySHelper.prototype.V_LOCK_STATUS,\nV_LEVEL: MySHelper.prototype.V_LEVEL,\nV_VOLTAGE: MySHelper.prototype.V_VOLTAGE, \nV_CURRENT: MySHelper.prototype.V_CURRENT,\nV_RGB: MySHelper.prototype.V_RGB,\nV_RGBW: MySHelper.prototype.V_RGBW,\nV_ID: MySHelper.prototype.V_ID,\nV_UNIT_PREFIX: MySHelper.prototype.V_UNIT_PREFIX,\nV_HVAC_SETPOINT_COOL:MySHelper.prototype.V_HVAC_SETPOINT_COOL,\nV_HVAC_SETPOINT_HEAT:MySHelper.prototype.V_HVAC_SETPOINT_HEAT,\nV_HVAC_FLOW_MODE: MySHelper.prototype.V_HVAC_FLOW_MODE,\nV_TEXT: MySHelper.prototype.V_TEXT\n};\n\n\n\nMySHelper.prototype.VString = function(V_SUBTYPE) {\n for (var prop in vtype ) \n if( vtype[ prop ] === parseInt(V_SUBTYPE) )\n return prop;\n};\n \n\nMySHelper.prototype.S_DOOR = 0; // Door sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_MOTION = 1; // Motion sensor; V_TRIPPED; V_ARMED \nMySHelper.prototype.S_SMOKE = 2; // Smoke sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_LIGHT = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nMySHelper.prototype.S_BINARY = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nMySHelper.prototype.S_DIMMER = 4; // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nMySHelper.prototype.S_COVER = 5; // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nMySHelper.prototype.S_TEMP = 6; // Temperature sensor; V_TEMP\nMySHelper.prototype.S_HUM = 7; // Humidity sensor; V_HUM\nMySHelper.prototype.S_BARO = 8; // Barometer sensor; V_PRESSURE; V_FORECAST\nMySHelper.prototype.S_WIND = 9; // Wind sensor; V_WIND; V_GUST\nMySHelper.prototype.S_RAIN = 10; // Rain sensor; V_RAIN; V_RAINRATE\nMySHelper.prototype.S_UV = 11; // Uv sensor; V_UV\nMySHelper.prototype.S_WEIGHT = 12; // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nMySHelper.prototype.S_POWER = 13; // Power meter; V_WATT; V_KWH\nMySHelper.prototype.S_HEATER = 14; // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nMySHelper.prototype.S_DISTANCE = 15; // Distance sensor; V_DISTANCE\nMySHelper.prototype.S_LIGHT_LEVEL = 16; // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nMySHelper.prototype.S_ARDUINO_NODE = 17 ; // Used (internally) for presenting a non-repeating Arduino node\nMySHelper.prototype.S_ARDUINO_REPEATER_NODE = 18; // Used (internally) for presenting a repeating Arduino node \nMySHelper.prototype.S_LOCK = 19; // Lock device; V_LOCK_STATUS\nMySHelper.prototype.S_IR = 20; // Ir device; V_IR_SEND; V_IR_RECEIVE\nMySHelper.prototype.S_WATER = 21; // Water meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_AIR_QUALITY = 22; // Air quality sensor; V_LEVEL\nMySHelper.prototype.S_CUSTOM = 23; // Custom sensor \nMySHelper.prototype.S_DUST = 24; // Dust sensor; V_LEVEL\nMySHelper.prototype.S_SCENE_CONTROLLER = 25; // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nMySHelper.prototype.S_RGB_LIGHT = 26; // RGB light. Send color component data using V_RGB. Also supports V_WATT \nMySHelper.prototype.S_RGBW_LIGHT = 27; // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nMySHelper.prototype.S_COLOR_SENSOR = 28; // Color sensor; send color information using V_RGB\nMySHelper.prototype.S_HVAC = 28; // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nMySHelper.prototype.S_MULTIMETER = 29; // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nMySHelper.prototype.S_SPRINKLER = 30; // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nMySHelper.prototype.S_WATER_LEAK = 31; // Water leak sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_SOUND = 32; // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nMySHelper.prototype.S_VIBRATION = 33; // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nMySHelper.prototype.S_MOISTURE = 34; // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nMySHelper.prototype.S_INFO = 35; // LCD text device / Simple information device on controller; V_TEXT\nMySHelper.prototype.S_GAS = 36; // Gas meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_GPS = 37; // GPS Sensor; V_POSITION\n \nvar stype = {\nS_DOOR: MySHelper.prototype.S_DOOR, // Door sensor; V_TRIPPED; V_ARMED\nS_MOTION: MySHelper.prototype.S_MOTION, // Motion sensor; V_TRIPPED; V_ARMED \nS_SMOKE: MySHelper.prototype.S_SMOKE, // Smoke sensor; V_TRIPPED; V_ARMED\nS_LIGHT: MySHelper.prototype.S_LIGHT, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nS_BINARY: MySHelper.prototype.S_BINARY, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nS_DIMMER: MySHelper.prototype.S_DIMMER, // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nS_COVER: MySHelper.prototype.S_COVER, // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nS_TEMP: MySHelper.prototype.S_TEMP, // Temperature sensor; V_TEMP\nS_HUM: MySHelper.prototype.S_HUM, // Humidity sensor; V_HUM\nS_BARO: MySHelper.prototype.S_BARO, // Barometer sensor; V_PRESSURE; V_FORECAST\nS_WIND: MySHelper.prototype.S_WIND, // Wind sensor; V_WIND; V_GUST\nS_RAIN: MySHelper.prototype.S_RAIN, // Rain sensor; V_RAIN; V_RAINRATE\nS_UV: MySHelper.prototype.S_UV, // Uv sensor; V_UV\nS_WEIGHT: MySHelper.prototype.S_WEIGHT, // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nS_POWER: MySHelper.prototype.S_POWER, // Power meter; V_WATT; V_KWH\nS_HEATER: MySHelper.prototype.S_HEATER, // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nS_DISTANCE: MySHelper.prototype.S_DISTANCE, // Distance sensor; V_DISTANCE\nS_LIGHT_LEVEL: MySHelper.prototype.S_LIGHT_LEVEL, // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nS_ARDUINO_NODE: MySHelper.prototype.S_ARDUINO_NODE, // Used (internally) for presenting a non-repeating Arduino node\nS_ARDUINO_REPEATER_NODE:MySHelper.prototype.S_ARDUINO_REPEATER_NODE, // Used (internally) for presenting a repeating Arduino node \nS_LOCK: MySHelper.prototype.S_LOCK, // Lock device; V_LOCK_STATUS\nS_IR: MySHelper.prototype.S_IR, // Ir device; V_IR_SEND; V_IR_RECEIVE\nS_WATER: MySHelper.prototype.S_WATER, // Water meter; V_FLOW; V_VOLUME\nS_AIR_QUALITY: MySHelper.prototype.S_AIR_QUALITY, // Air quality sensor; V_LEVEL\nS_CUSTOM: MySHelper.prototype.S_CUSTOM, // Custom sensor \nS_DUST: MySHelper.prototype.S_DUST, // Dust sensor; V_LEVEL\nS_SCENE_CONTROLLER: MySHelper.prototype.S_SCENE_CONTROLLER, // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nS_RGB_LIGHT: MySHelper.prototype.S_RGB_LIGHT, // RGB light. Send color component data using V_RGB. Also supports V_WATT \nS_RGBW_LIGHT: MySHelper.prototype.S_RGBW_LIGHT, // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nS_COLOR_SENSOR: MySHelper.prototype.S_COLOR_SENSOR, // Color sensor; send color information using V_RGB\nS_HVAC: MySHelper.prototype.S_HVAC, // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nS_MULTIMETER: MySHelper.prototype.S_MULTIMETER, // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nS_SPRINKLER: MySHelper.prototype.S_SPRINKLER, // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nS_WATER_LEAK: MySHelper.prototype.S_WATER_LEAK, // Water leak sensor; V_TRIPPED; V_ARMED\nS_SOUND: MySHelper.prototype.S_SOUND, // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nS_VIBRATION: MySHelper.prototype.S_VIBRATION, // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nS_MOISTURE: MySHelper.prototype.S_MOISTURE, // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nS_INFO: MySHelper.prototype.S_INFO, // LCD text device / Simple information device on controller; V_TEXT\nS_GAS: MySHelper.prototype.S_GAS, // Gas meter; V_FLOW; V_VOLUME\nS_GPS: MySHelper.prototype.S_GPS // GPS Sensor; V_POSITION\n};\n\nMySHelper.prototype.SString = function(S_SUBTYPE) {\n for (var prop in stype ) \n if( stype[ prop ] === parseInt(S_SUBTYPE) )\n return prop;\n}; \n \n}\n\n\nvar MySHelperObj = new MySHelper();\n\ncontext.global.MYS = MySHelperObj;\n\nreturn msg;","outputs":1,"noerr":0,"x":325.25,"y":59.00000190734863,"z":"9592163f.6a6de8","wires":[[]]},{"id":"df1e322.f20e1d","type":"function","name":"Set Controller 1","func":"msg.controller = 1\n\nreturn msg;","outputs":1,"noerr":0,"x":602.0000076293945,"y":140.50000190734863,"z":"9592163f.6a6de8","wires":[["ebcef3df.14311"]]},{"id":"266b87b3.d99478","type":"switch","name":"route to controller n","property":"controller","rules":[{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"false","outputs":4,"x":94,"y":207.25000381469727,"z":"9592163f.6a6de8","wires":[["5f03c10e.a0fc4"],["c7d0d88b.382f28"],[],[]]},{"id":"c7d0d88b.382f28","type":"tcp request","server":"192.168.92.14","port":"5003","out":"char","splitc":"\\n","name":"MySWifi ESP8266 GW AES 14","x":370.5,"y":217.25000381469727,"z":"9592163f.6a6de8","wires":[["c5f14d8f.3a0eb"]]},{"id":"c5f14d8f.3a0eb","type":"function","name":"Set Controller 2","func":"msg.controller = 2\n\nreturn msg;","outputs":1,"noerr":0,"x":597.5000076293945,"y":218.750018119812,"z":"9592163f.6a6de8","wires":[["ebcef3df.14311"]]},{"id":"56b9f6ab.a94608","type":"file in","name":"read store for next ids","filename":"mysids.dump","format":"utf8","x":346,"y":97,"z":"9592163f.6a6de8","wires":[["57db23d6.a824dc"]]},{"id":"e000bd09.1fff4","type":"debug","name":"Debug","active":true,"console":"false","complete":"true","x":785,"y":470,"z":"9592163f.6a6de8","wires":[]},{"id":"57db23d6.a824dc","type":"function","name":"store to context.global.mysnextid","func":"if (msg.payload === undefined) {\n var mysnextid = {};\n\n obj = mysnextid; \n}\nelse \n{\ntry{\n obj = JSON.parse(msg.payload);\n }\n catch(e){\n \n var mysnextid = {};\n\n obj = mysnextid;\n \n }\n} \n\ncontext.global.mysnextid = obj;\n\nmsg.payload = context.global.mysnextid;\n\nreturn msg;","outputs":1,"noerr":0,"x":591,"y":96,"z":"9592163f.6a6de8","wires":[[]]},{"id":"dfba7d69.20458","type":"file","name":"dump mysids","filename":"mysids.dump","appendNewline":true,"createDir":false,"overwriteFile":"true","x":1434,"y":375,"z":"9592163f.6a6de8","wires":[]},{"id":"25efb0d3.da105","type":"inject","name":"Test Backup","topic":"","payload":"","payloadType":"none","repeat":"","crontab":"","once":false,"x":209,"y":456,"z":"9592163f.6a6de8","wires":[["e7d998a7.182668"]]},{"id":"e7d998a7.182668","type":"function","name":"Show context.global.mysnextid","func":"msg.payload = JSON.stringify(context.global.mysnextid);\n\nreturn msg;","outputs":1,"noerr":0,"x":427,"y":453,"z":"9592163f.6a6de8","wires":[["e000bd09.1fff4"]]},{"id":"e0e76d62.1f189","type":"function","name":"handle nextids","func":"// increase nextid, if nodeid >= nextid \n\nif (msg.nodeid < 255)\n{\n if (context.global.mysnextid[msg.controller] === undefined) {\n context.global.mysnextid[msg.controller] = msg.nodeid+1;\n }\n \n if (msg.nodeid >= context.global.mysnextid[msg.controller]) {\n context.global.mysnextid[msg.controller] = msg.nodeid+1; \n }\n \n}\n\nreturn msg;","outputs":1,"noerr":0,"x":1223,"y":368,"z":"9592163f.6a6de8","wires":[["dfba7d69.20458"]]},{"id":"a7d335f6.582cc8","type":"inject","name":"Test GetNodeId","topic":"","payload":"255;0;3;0;3;","payloadType":"string","repeat":"","crontab":"","once":false,"x":456,"y":264,"z":"9592163f.6a6de8","wires":[["c5f14d8f.3a0eb"]]}]Features:
- Publish states to mqtt
- handle node-ids
- support multiple ethernet conrollers
- should be adoptable to serial controllers
Restrictions:
- read only, no values can be sent to nodes
- you will find others :)
-
- Fixed node-id handling for new nodes.
- added write support (see "MQTT to MYS" convert for details)
- parameters can be set in 'MYS initialize'
[{"id":"ba386057.845d3","type":"mqtt-broker","broker":"192.168.92.4","port":"1883","clientid":"NodeRed"},{"id":"e6ce260d.1931d8","type":"switch","z":"9592163f.6a6de8","name":"switch message type","property":"messageType","rules":[{"t":"eq","v":"0"},{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"true","outputs":5,"x":1259.166648864746,"y":182.50001335144043,"wires":[["8c663d73.7399c"],["4a1e5f84.b5e1a"],["7753f9a2.88ac08"],["1e4aa61b.e1b55a"],["60a0dde4.9f5f24"]]},{"id":"8c663d73.7399c","type":"function","z":"9592163f.6a6de8","name":"presentation","func":"msg.subTypeString = context.global.MYS.SString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1488.916648864746,"y":45.24998474121094,"wires":[["df9e131d.2061f","4d15a037.b2ea6"]]},{"id":"7753f9a2.88ac08","type":"function","z":"9592163f.6a6de8","name":"req","func":"msg.topic = \"req\";\nreturn msg;","outputs":1,"noerr":0,"x":1484.5000228881836,"y":182.75000190734863,"wires":[["4d15a037.b2ea6"]]},{"id":"1e4aa61b.e1b55a","type":"function","z":"9592163f.6a6de8","name":"internal","func":"msg.subTypeString = context.global.MYS.IString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1488.5000228881836,"y":233.00000190734863,"wires":[["df9e131d.2061f","4d15a037.b2ea6","b5e4f17d.4a1b1"]]},{"id":"60a0dde4.9f5f24","type":"function","z":"9592163f.6a6de8","name":"stream","func":"msg.topic = \"stream\";\nreturn msg;","outputs":1,"x":1496.5000228881836,"y":328.00000190734863,"wires":[[]]},{"id":"4d15a037.b2ea6","type":"debug","z":"9592163f.6a6de8","name":"debug","active":false,"console":"false","complete":"true","x":1845.7500267028809,"y":242.00000286102295,"wires":[]},{"id":"4a1e5f84.b5e1a","type":"function","z":"9592163f.6a6de8","name":"set","func":"msg.subTypeString = context.global.MYS.VString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\n\nreturn msg;","outputs":1,"noerr":0,"x":1492.166648864746,"y":107.5,"wires":[["4d15a037.b2ea6","df9e131d.2061f"]]},{"id":"fc54bb91.03ab48","type":"debug","z":"9592163f.6a6de8","name":"","active":false,"console":"false","complete":"true","x":1218.9166259765625,"y":41.66668510437012,"wires":[]},{"id":"6aa2d9f6.955d28","type":"function","z":"9592163f.6a6de8","name":"Split GW Message","func":"\n var tokens = msg.payload.split(\";\")\n \n msg.rawData = tokens;\n if(tokens.length >= 6)\n {\n msg.nodeId = parseInt(tokens[0]);\n msg.childSensorId = parseInt(tokens[1]);\n msg.messageType = parseInt(tokens[2]);\n msg.ack = parseInt(tokens[3]);\n msg.subType = parseInt(tokens[4]);\n msg.payload = tokens[5];\n for (j=6; j<tokens.length; j++) \n msg.payload = msg.payload + ';' + tokens[j];\n }\n\nreturn msg;","outputs":1,"noerr":0,"x":1023.6666488647461,"y":180.66664123535156,"wires":[["e6ce260d.1931d8","fc54bb91.03ab48","e0e76d62.1f189"]]},{"id":"df9e131d.2061f","type":"mqtt out","z":"9592163f.6a6de8","name":"Publish to MQTT","topic":"","qos":"","retain":"","broker":"ba386057.845d3","x":1858.9166526794434,"y":181.16665649414062,"wires":[]},{"id":"b5e4f17d.4a1b1","type":"function","z":"9592163f.6a6de8","name":"hanlde internal messages","func":"//msg.subTypeString = \"\";\n//msg.topic = \"internal respones\";\n\nif (msg.subTypeString == 'I_TIME')\n{\n var payload = parseInt(new Date().getTime()/1000);\n\tvar command = context.global.MYS.T_INTERNAL; \n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_TIME; // I_TIME\n\tmsg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg;\n \n}\nelse if (msg.subTypeString == 'I_ID_REQUEST')\n{\n msg.topic = \"I_ID_RESPONSE\";\n msg.subTypeString = \"I_ID_RESPONSE\";\n // 255;255;3;0;4;8 for ID 8\n var command = context.global.MYS.T_INTERNAL;\n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_ID_RESPONSE; // I_ID_RESPONSE\n\n\tif (context.global.mysnextid[msg.controller] === undefined) {\n\t payload = context.global.MYS.MIN_NODEID;\n\t} \n\telse\n\t{\n\t payload = context.global.mysnextid[msg.controller];\n\t}\n\t\n msg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg; \n} \nelse if (msg.subTypeString == 'I_CONFIG')\n{\n var payload = 'M';\n\tvar command = context.global.MYS.T_INTERNAL; \n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_CONFIG; // I_TIME\n\tmsg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg;\n}\nelse if (msg.subTypeString == 'I_INCLUSION_MODE')\n{\n // not yet implemented\n}\n\nreturn;\n\n\n","outputs":1,"noerr":0,"x":1694.916648864746,"y":543.4166889190674,"wires":[["4d15a037.b2ea6","266b87b3.d99478"]]},{"id":"e6d67f33.19298","type":"inject","z":"9592163f.6a6de8","name":"Startup","topic":"","payload":"","payloadType":"none","repeat":"","crontab":"","once":true,"x":145.25,"y":81.41665363311768,"wires":[["64617800.9b9e88","56b9f6ab.a94608","3e866f6d.c1799"]]},{"id":"ebcef3df.14311","type":"function","z":"9592163f.6a6de8","name":"ToString","func":"msg.payload = msg.payload.toString().replace(/[\\n\\r]/g, '');\n\nreturn msg;","outputs":1,"noerr":0,"x":829.1666946411133,"y":181.91668796539307,"wires":[["6aa2d9f6.955d28"]]},{"id":"31047fa6.cefb8","type":"catch","z":"9592163f.6a6de8","name":"","x":58,"y":449,"wires":[["3622f9b9.c9dd06"]]},{"id":"3622f9b9.c9dd06","type":"debug","z":"9592163f.6a6de8","name":"","active":false,"console":"false","complete":"true","x":224,"y":450,"wires":[]},{"id":"64617800.9b9e88","type":"function","z":"9592163f.6a6de8","name":"MYS Initialize","func":"function MySHelper() { \n\nMySHelper.prototype.TOPIC_PREFIX = \"MYS-NODERED\";\n\nMySHelper.prototype.MIN_NODEID = 10;\n\n\n// don't touch below :)\n \nMySHelper.prototype.T_PRESENTATION = 0;\nMySHelper.prototype.T_SET = 1;\nMySHelper.prototype.T_REQ = 2;\nMySHelper.prototype.T_INTERNAL = 3;\nMySHelper.prototype.T_STREAM = 4;\n\nMySHelper.prototype.I_BATTERY_LEVEL = 0;\nMySHelper.prototype.I_TIME = 1;\nMySHelper.prototype.I_VERSION = 2;\nMySHelper.prototype.I_ID_REQUEST = 3;\nMySHelper.prototype.I_ID_RESPONSE = 4;\nMySHelper.prototype.I_INCLUSION_MODE = 5;\nMySHelper.prototype.I_CONFIG = 6;\nMySHelper.prototype.I_PING = 7;\nMySHelper.prototype.I_PING_ACK = 8;\nMySHelper.prototype.I_LOG_MESSAGE = 9;\nMySHelper.prototype.I_CHILDREN = 10;\nMySHelper.prototype.I_SKETCH_NAME = 11;\nMySHelper.prototype.I_SKETCH_VERSION = 12;\nMySHelper.prototype.I_REBOOT = 13;\nMySHelper.prototype.I_GATEWAY_READY = 14;\nMySHelper.prototype.I_REQUEST_SIGNING = 15;\nMySHelper.prototype.I_GET_NONCE = 16;\nMySHelper.prototype.I_GET_NONCE_RESPONSE = 17;\nMySHelper.prototype.I_HEARTBEAT = 18;\nMySHelper.prototype.I_PRESENTATION = 19;\n \nvar itype = {\nI_BATTERY_LEVEL: MySHelper.prototype.I_BATTERY_LEVEL,\nI_TIME: MySHelper.prototype.I_TIME,\nI_VERSION: MySHelper.prototype.I_VERSION,\nI_ID_REQUEST: MySHelper.prototype.I_ID_REQUEST,\nI_ID_RESPONSE: MySHelper.prototype.I_ID_RESPONSE,\nI_INCLUSION_MODE: MySHelper.prototype.I_INCLUSION_MODE,\nI_CONFIG: MySHelper.prototype.I_CONFIG,\nI_PING: MySHelper.prototype.I_PING,\nI_PING_ACK: MySHelper.prototype.I_PING_ACK,\nI_LOG_MESSAGE: MySHelper.prototype.I_LOG_MESSAGE,\nI_CHILDREN: MySHelper.prototype.I_CHILDREN,\nI_SKETCH_NAME: MySHelper.prototype.I_SKETCH_NAME,\nI_SKETCH_VERSION: MySHelper.prototype.I_SKETCH_VERSION,\nI_REBOOT: MySHelper.prototype.I_REBOOT,\nI_GATEWAY_READY: MySHelper.prototype.I_GATEWAY_READY,\nI_REQUEST_SIGNING: MySHelper.prototype.I_REQUEST_SIGNING,\nI_GET_NONCE: MySHelper.prototype.I_GET_NONCE,\nI_GET_NONCE_RESPONSE: MySHelper.prototype.I_GET_NONCE_RESPONSE,\nI_HEARTBEAT: MySHelper.prototype.I_HEARTBEAT,\nI_PRESENTATION: MySHelper.prototype.I_PRESENTATION\n};\n\nMySHelper.prototype.IString = function(I_SUBTYPE) {\n for (var prop in itype ) \n if( itype[ prop ] === parseInt(I_SUBTYPE) )\n return prop;\n};\n\nMySHelper.prototype.V_TEMP = 0;\nMySHelper.prototype.V_HUM = 1;\nMySHelper.prototype.V_LIGHT = 2;\nMySHelper.prototype.V_STATUS = 2;\nMySHelper.prototype.V_DIMMER = 3;\nMySHelper.prototype.V_PRESSURE = 4;\nMySHelper.prototype.V_FORECAST = 5;\nMySHelper.prototype.V_RAIN = 6;\nMySHelper.prototype.V_RAINRATE = 7;\nMySHelper.prototype.V_WIND = 8;\nMySHelper.prototype.V_GUST = 9;\nMySHelper.prototype.V_DIRECTION = 10;\nMySHelper.prototype.V_UV = 11;\nMySHelper.prototype.V_WEIGHT = 12;\nMySHelper.prototype.V_DISTANCE = 13;\nMySHelper.prototype.V_IMPEDANCE = 14;\nMySHelper.prototype.V_ARMED = 15;\nMySHelper.prototype.V_TRIPPED = 16;\nMySHelper.prototype.V_WATT = 17;\nMySHelper.prototype.V_KWH = 18;\nMySHelper.prototype.V_SCENE_ON = 19;\nMySHelper.prototype.V_SCENE_OFF = 20;\nMySHelper.prototype.V_HEATER = 21;\nMySHelper.prototype.V_HEATER_SW = 22;\nMySHelper.prototype.V_LIGHT_LEVEL = 23;\nMySHelper.prototype.V_VAR1 = 24;\nMySHelper.prototype.V_VAR2 = 25;\nMySHelper.prototype.V_VAR3 = 26;\nMySHelper.prototype.V_VAR4 = 27;\nMySHelper.prototype.V_VAR5 = 28;\nMySHelper.prototype.V_UP = 29;\nMySHelper.prototype.V_DOWN = 30;\nMySHelper.prototype.V_STOP = 31;\nMySHelper.prototype.V_IR_SEND = 32;\nMySHelper.prototype.V_IR_RECEIVE = 33;\nMySHelper.prototype.V_FLOW = 34;\nMySHelper.prototype.V_VOLUME = 35;\nMySHelper.prototype.V_LOCK_STATUS = 36;\nMySHelper.prototype.V_LEVEL = 37; \nMySHelper.prototype.V_VOLTAGE = 38; \nMySHelper.prototype.V_CURRENT = 39; \nMySHelper.prototype.V_RGB = 40; \nMySHelper.prototype.V_RGBW = 41;\nMySHelper.prototype.V_ID = 42;\nMySHelper.prototype.V_UNIT_PREFIX = 43;\nMySHelper.prototype.V_HVAC_SETPOINT_COOL = 44;\nMySHelper.prototype.V_HVAC_SETPOINT_HEAT = 45;\nMySHelper.prototype.V_HVAC_FLOW_MODE = 46;\nMySHelper.prototype.V_TEXT = 47;\n\nvar vtype = {\nV_TEMP: MySHelper.prototype.V_TEMP,\nV_HUM: MySHelper.prototype.V_HUM,\nV_STATUS: MySHelper.prototype.V_STATUS,\nV_LIGHT: MySHelper.prototype.V_LIGHT,\nV_DIMMER: MySHelper.prototype.V_DIMMER,\nV_PRESSURE: MySHelper.prototype.V_PRESSURE,\nV_FORECAST: MySHelper.prototype.V_FORECAST,\nV_RAIN: MySHelper.prototype.V_RAIN,\nV_RAINRATE: MySHelper.prototype.V_RAINRATE,\nV_WIND: MySHelper.prototype.V_WIND,\nV_GUST: MySHelper.prototype.V_GUST,\nV_DIRECTION: MySHelper.prototype.V_DIRECTION,\nV_UV: MySHelper.prototype.V_UV,\nV_WEIGHT: MySHelper.prototype.V_WEIGHT,\nV_DISTANCE: MySHelper.prototype.V_DISTANCE,\nV_IMPEDANCE: MySHelper.prototype.V_IMPEDANCE,\nV_ARMED: MySHelper.prototype.V_ARMED,\nV_TRIPPED: MySHelper.prototype.V_TRIPPED,\nV_WATT: MySHelper.prototype.V_WATT,\nV_KWH: MySHelper.prototype.V_KWH,\nV_SCENE_ON: MySHelper.prototype.V_SCENE_ON,\nV_SCENE_OFF: MySHelper.prototype.V_SCENE_OFF,\nV_HEATER: MySHelper.prototype.V_HEATER,\nV_HEATER_SW: MySHelper.prototype.V_HEATER_SW,\nV_LIGHT_LEVEL: MySHelper.prototype.V_LIGHT_LEVEL,\nV_VAR1: MySHelper.prototype.V_VAR1,\nV_VAR2: MySHelper.prototype.V_VAR2,\nV_VAR3: MySHelper.prototype.V_VAR3,\nV_VAR4: MySHelper.prototype.V_VAR4,\nV_VAR5: MySHelper.prototype.V_VAR5,\nV_UP: MySHelper.prototype.V_UP,\nV_DOWN: MySHelper.prototype.V_DOWN,\nV_STOP: MySHelper.prototype.V_STOP,\nV_IR_SEND: MySHelper.prototype.V_IR_SEND,\nV_IR_RECEIVE: MySHelper.prototype.V_IR_RECEIVE,\nV_FLOW: MySHelper.prototype.V_FLOW,\nV_VOLUME: MySHelper.prototype.V_VOLUME,\nV_LOCK_STATUS: MySHelper.prototype.V_LOCK_STATUS,\nV_LEVEL: MySHelper.prototype.V_LEVEL,\nV_VOLTAGE: MySHelper.prototype.V_VOLTAGE, \nV_CURRENT: MySHelper.prototype.V_CURRENT,\nV_RGB: MySHelper.prototype.V_RGB,\nV_RGBW: MySHelper.prototype.V_RGBW,\nV_ID: MySHelper.prototype.V_ID,\nV_UNIT_PREFIX: MySHelper.prototype.V_UNIT_PREFIX,\nV_HVAC_SETPOINT_COOL:MySHelper.prototype.V_HVAC_SETPOINT_COOL,\nV_HVAC_SETPOINT_HEAT:MySHelper.prototype.V_HVAC_SETPOINT_HEAT,\nV_HVAC_FLOW_MODE: MySHelper.prototype.V_HVAC_FLOW_MODE,\nV_TEXT: MySHelper.prototype.V_TEXT\n};\n\n\n\nMySHelper.prototype.VString = function(V_SUBTYPE) {\n for (var prop in vtype ) \n if( vtype[ prop ] === parseInt(V_SUBTYPE) )\n return prop;\n};\n \nMySHelper.prototype.VNum = function(V_SUBTYPE) {\n sRet = vtype [V_SUBTYPE];\n if (sRet === undefined)\n sRet = V_SUBTYPE;\n return sRet;\n}\n\nMySHelper.prototype.S_DOOR = 0; // Door sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_MOTION = 1; // Motion sensor; V_TRIPPED; V_ARMED \nMySHelper.prototype.S_SMOKE = 2; // Smoke sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_LIGHT = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nMySHelper.prototype.S_BINARY = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nMySHelper.prototype.S_DIMMER = 4; // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nMySHelper.prototype.S_COVER = 5; // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nMySHelper.prototype.S_TEMP = 6; // Temperature sensor; V_TEMP\nMySHelper.prototype.S_HUM = 7; // Humidity sensor; V_HUM\nMySHelper.prototype.S_BARO = 8; // Barometer sensor; V_PRESSURE; V_FORECAST\nMySHelper.prototype.S_WIND = 9; // Wind sensor; V_WIND; V_GUST\nMySHelper.prototype.S_RAIN = 10; // Rain sensor; V_RAIN; V_RAINRATE\nMySHelper.prototype.S_UV = 11; // Uv sensor; V_UV\nMySHelper.prototype.S_WEIGHT = 12; // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nMySHelper.prototype.S_POWER = 13; // Power meter; V_WATT; V_KWH\nMySHelper.prototype.S_HEATER = 14; // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nMySHelper.prototype.S_DISTANCE = 15; // Distance sensor; V_DISTANCE\nMySHelper.prototype.S_LIGHT_LEVEL = 16; // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nMySHelper.prototype.S_ARDUINO_NODE = 17 ; // Used (internally) for presenting a non-repeating Arduino node\nMySHelper.prototype.S_ARDUINO_REPEATER_NODE = 18; // Used (internally) for presenting a repeating Arduino node \nMySHelper.prototype.S_LOCK = 19; // Lock device; V_LOCK_STATUS\nMySHelper.prototype.S_IR = 20; // Ir device; V_IR_SEND; V_IR_RECEIVE\nMySHelper.prototype.S_WATER = 21; // Water meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_AIR_QUALITY = 22; // Air quality sensor; V_LEVEL\nMySHelper.prototype.S_CUSTOM = 23; // Custom sensor \nMySHelper.prototype.S_DUST = 24; // Dust sensor; V_LEVEL\nMySHelper.prototype.S_SCENE_CONTROLLER = 25; // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nMySHelper.prototype.S_RGB_LIGHT = 26; // RGB light. Send color component data using V_RGB. Also supports V_WATT \nMySHelper.prototype.S_RGBW_LIGHT = 27; // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nMySHelper.prototype.S_COLOR_SENSOR = 28; // Color sensor; send color information using V_RGB\nMySHelper.prototype.S_HVAC = 28; // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nMySHelper.prototype.S_MULTIMETER = 29; // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nMySHelper.prototype.S_SPRINKLER = 30; // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nMySHelper.prototype.S_WATER_LEAK = 31; // Water leak sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_SOUND = 32; // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nMySHelper.prototype.S_VIBRATION = 33; // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nMySHelper.prototype.S_MOISTURE = 34; // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nMySHelper.prototype.S_INFO = 35; // LCD text device / Simple information device on controller; V_TEXT\nMySHelper.prototype.S_GAS = 36; // Gas meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_GPS = 37; // GPS Sensor; V_POSITION\n \nvar stype = {\nS_DOOR: MySHelper.prototype.S_DOOR, // Door sensor; V_TRIPPED; V_ARMED\nS_MOTION: MySHelper.prototype.S_MOTION, // Motion sensor; V_TRIPPED; V_ARMED \nS_SMOKE: MySHelper.prototype.S_SMOKE, // Smoke sensor; V_TRIPPED; V_ARMED\nS_LIGHT: MySHelper.prototype.S_LIGHT, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nS_BINARY: MySHelper.prototype.S_BINARY, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nS_DIMMER: MySHelper.prototype.S_DIMMER, // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nS_COVER: MySHelper.prototype.S_COVER, // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nS_TEMP: MySHelper.prototype.S_TEMP, // Temperature sensor; V_TEMP\nS_HUM: MySHelper.prototype.S_HUM, // Humidity sensor; V_HUM\nS_BARO: MySHelper.prototype.S_BARO, // Barometer sensor; V_PRESSURE; V_FORECAST\nS_WIND: MySHelper.prototype.S_WIND, // Wind sensor; V_WIND; V_GUST\nS_RAIN: MySHelper.prototype.S_RAIN, // Rain sensor; V_RAIN; V_RAINRATE\nS_UV: MySHelper.prototype.S_UV, // Uv sensor; V_UV\nS_WEIGHT: MySHelper.prototype.S_WEIGHT, // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nS_POWER: MySHelper.prototype.S_POWER, // Power meter; V_WATT; V_KWH\nS_HEATER: MySHelper.prototype.S_HEATER, // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nS_DISTANCE: MySHelper.prototype.S_DISTANCE, // Distance sensor; V_DISTANCE\nS_LIGHT_LEVEL: MySHelper.prototype.S_LIGHT_LEVEL, // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nS_ARDUINO_NODE: MySHelper.prototype.S_ARDUINO_NODE, // Used (internally) for presenting a non-repeating Arduino node\nS_ARDUINO_REPEATER_NODE:MySHelper.prototype.S_ARDUINO_REPEATER_NODE, // Used (internally) for presenting a repeating Arduino node \nS_LOCK: MySHelper.prototype.S_LOCK, // Lock device; V_LOCK_STATUS\nS_IR: MySHelper.prototype.S_IR, // Ir device; V_IR_SEND; V_IR_RECEIVE\nS_WATER: MySHelper.prototype.S_WATER, // Water meter; V_FLOW; V_VOLUME\nS_AIR_QUALITY: MySHelper.prototype.S_AIR_QUALITY, // Air quality sensor; V_LEVEL\nS_CUSTOM: MySHelper.prototype.S_CUSTOM, // Custom sensor \nS_DUST: MySHelper.prototype.S_DUST, // Dust sensor; V_LEVEL\nS_SCENE_CONTROLLER: MySHelper.prototype.S_SCENE_CONTROLLER, // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nS_RGB_LIGHT: MySHelper.prototype.S_RGB_LIGHT, // RGB light. Send color component data using V_RGB. Also supports V_WATT \nS_RGBW_LIGHT: MySHelper.prototype.S_RGBW_LIGHT, // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nS_COLOR_SENSOR: MySHelper.prototype.S_COLOR_SENSOR, // Color sensor; send color information using V_RGB\nS_HVAC: MySHelper.prototype.S_HVAC, // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nS_MULTIMETER: MySHelper.prototype.S_MULTIMETER, // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nS_SPRINKLER: MySHelper.prototype.S_SPRINKLER, // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nS_WATER_LEAK: MySHelper.prototype.S_WATER_LEAK, // Water leak sensor; V_TRIPPED; V_ARMED\nS_SOUND: MySHelper.prototype.S_SOUND, // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nS_VIBRATION: MySHelper.prototype.S_VIBRATION, // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nS_MOISTURE: MySHelper.prototype.S_MOISTURE, // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nS_INFO: MySHelper.prototype.S_INFO, // LCD text device / Simple information device on controller; V_TEXT\nS_GAS: MySHelper.prototype.S_GAS, // Gas meter; V_FLOW; V_VOLUME\nS_GPS: MySHelper.prototype.S_GPS // GPS Sensor; V_POSITION\n};\n\nMySHelper.prototype.SString = function(S_SUBTYPE) {\n for (var prop in stype ) \n if( stype[ prop ] === parseInt(S_SUBTYPE) )\n return prop;\n}; \n \n MySHelper.prototype.encode = function(destination, sensor, command, acknowledge, type, payload) {\n\tvar msg = destination.toString(10) + \";\" + sensor.toString(10) + \";\" + command.toString(10) + \";\" + acknowledge.toString(10) + \";\" + type.toString(10) + \";\";\n\tif (command == 4) {\n\t\tfor (var i = 0; i < payload.length; i++) {\n\t\t\tif (payload[i] < 16)\n\t\t\t\tmsg += \"0\";\n\t\t\tmsg += payload[i].toString(16);\n\t\t}\n\t} else {\n\t\tmsg += payload;\n\t}\n\tmsg += '\\n';\n\treturn msg.toString();\n}\n}\n\n\nvar MySHelperObj = new MySHelper();\n\ncontext.global.MYS = MySHelperObj;\n\nreturn msg;","outputs":1,"noerr":0,"x":364.25,"y":65.99999809265137,"wires":[[]]},{"id":"df1e322.f20e1d","type":"function","z":"9592163f.6a6de8","name":"Set Controller 1","func":"msg.controller = 1\n\nreturn msg;","outputs":1,"noerr":0,"x":641.0000076293945,"y":147.49999809265137,"wires":[["ebcef3df.14311"]]},{"id":"266b87b3.d99478","type":"switch","z":"9592163f.6a6de8","name":"route to controller n","property":"controller","rules":[{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"false","outputs":4,"x":133,"y":214.25,"wires":[["3e866f6d.c1799"],["c7d0d88b.382f28"],[],[]]},{"id":"c7d0d88b.382f28","type":"tcp request","z":"9592163f.6a6de8","server":"192.168.92.14","port":"5003","out":"sit","splitc":"0","name":"MySWifi ESP8266 GW AES 14","x":410.5,"y":207.24999618530273,"wires":[["c5f14d8f.3a0eb"]]},{"id":"c5f14d8f.3a0eb","type":"function","z":"9592163f.6a6de8","name":"Set Controller 2","func":"msg.controller = 2\n\nreturn msg;","outputs":1,"noerr":0,"x":653.5,"y":205.7500114440918,"wires":[["ebcef3df.14311"]]},{"id":"56b9f6ab.a94608","type":"file in","z":"9592163f.6a6de8","name":"read store for next ids","filename":"mysids.dump","format":"utf8","x":385,"y":103.99999618530273,"wires":[["57db23d6.a824dc"]]},{"id":"e000bd09.1fff4","type":"debug","z":"9592163f.6a6de8","name":"Debug","active":false,"console":"false","complete":"true","x":732,"y":361,"wires":[]},{"id":"57db23d6.a824dc","type":"function","z":"9592163f.6a6de8","name":"store to context.global.mysnextid","func":"if (msg.payload === undefined) {\n var mysnextid = {};\n\n obj = mysnextid; \n}\nelse \n{\ntry{\n obj = JSON.parse(msg.payload);\n }\n catch(e){\n \n var mysnextid = {};\n\n obj = mysnextid;\n \n }\n} \n\ncontext.global.mysnextid = obj;\n\nmsg.payload = context.global.mysnextid;\n\nreturn msg;","outputs":1,"noerr":0,"x":630,"y":102.99999618530273,"wires":[[]]},{"id":"dfba7d69.20458","type":"file","z":"9592163f.6a6de8","name":"dump mysids","filename":"mysids.dump","appendNewline":true,"createDir":false,"overwriteFile":"true","x":1473,"y":381.99999618530273,"wires":[]},{"id":"e0e76d62.1f189","type":"function","z":"9592163f.6a6de8","name":"handle nextids","func":"// increase nextid, if nodeid >= nextid \n// node.log(\"Handling next ids\");\n// node.log(\"nodeId: \" + msg.nodeId);\n\nbChanged = false;\n\nif (msg.nodeId === 0) return;\n\nif (msg.nodeId < 255)\n{\n // node.log(\"Test if next node-id must be set\");\n if (context.global.mysnextid[msg.controller] === undefined) {\n node.log(\"node-id not initialized yet\");\n context.global.mysnextid[msg.controller] = msg.nodeId+1;\n if (context.global.mysnextid[msg.controller] < context.global.MYS.MIN_NODEID)\n context.global.mysnextid[msg.controller] = context.global.MYS.MIN_NODEID;\n bChanged = true;\n }\n \n // node.log(\"Nexid stored \" + parseInt(context.global.mysnextid[msg.controller]));\n \n if (msg.nodeId >= parseInt(context.global.mysnextid[msg.controller])) {\n node.log(\"node-id >= next -> increase\");\n // convert to int\n context.global.mysnextid[msg.controller] = parseInt(context.global.mysnextid[msg.controller]);\n context.global.mysnextid[msg.controller] = msg.nodeId+1; \n if (context.global.mysnextid[msg.controller] < context.global.MYS.MIN_NODEID)\n context.global.mysnextid[msg.controller] = context.global.MYS.MIN_NODEID;\n bChanged = true;\n }\n\n if (bChanged) {\n node.log(\"next id must be stored\");\n msg.payload = JSON.stringify(context.global.mysnextid); \n return msg;\n }\n}\n\n\n","outputs":1,"noerr":0,"x":1262,"y":374.99999618530273,"wires":[["dfba7d69.20458","5c074c19.a3f8b4"]]},{"id":"8da09002.725f7","type":"function","z":"9592163f.6a6de8","name":"MQTT to MYS convert","func":"// topic = MYS-NODERED/set/controller/node-id/sensor-id/ack/sub-type\n// payload = payload :)\n\n var tokens = msg.topic.split(\"/\")\n \n msg.rawData = tokens;\n msg.tokens = tokens.length;\n if(tokens.length == 7)\n {\n if (tokens[0] != context.global.MYS.TOPIC_PREFIX) // not for us\n return;\n if (tokens[1] != 'set') // not for us\n return;\n \n msg.controller = parseInt(tokens[2]);\n msg.messageType = context.global.MYS.T_SET;\n msg.nodeId = parseInt(tokens[3]);\n msg.childSensorId = parseInt(tokens[4]);\n msg.ack = parseInt(tokens[5]);\n msg.subType = context.global.MYS.VNum(tokens[6]);\n \n msg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, msg.messageType, msg.ack, msg.subType, msg.payload);\n \n return msg; \n }\n","outputs":1,"noerr":0,"x":490,"y":361,"wires":[["e000bd09.1fff4","266b87b3.d99478"]]},{"id":"3e866f6d.c1799","type":"tcp request","z":"9592163f.6a6de8","server":"192.168.92.13","port":"5003","out":"sit","splitc":"0","name":"MySWifi ESP8266 GW AES 13","x":407,"y":145.99999618530273,"wires":[["df1e322.f20e1d"]]},{"id":"5c074c19.a3f8b4","type":"debug","z":"9592163f.6a6de8","name":"","active":true,"console":"false","complete":"false","x":1454,"y":543.9999961853027,"wires":[]},{"id":"c75fd7f4.38a028","type":"mqtt in","z":"9592163f.6a6de8","name":"Read MQTT Stream: change Topic to your needs","topic":"MYS-NODERED/set/#","broker":"ba386057.845d3","x":183.5,"y":362,"wires":[["8da09002.725f7"]]}]``` -
Stability is not sufficient. The connection gets lost from time to time.
Added a watchdog to add another connection, if no messages arrives.
Seems, that this is only interesting for me. If I get no feedback I will stop spaming this thread. :smiley:
[{"id":"ba386057.845d3","type":"mqtt-broker","broker":"192.168.92.4","port":"1883","clientid":"NodeRed"},{"id":"e6ce260d.1931d8","type":"switch","z":"9592163f.6a6de8","name":"switch message type","property":"messageType","rules":[{"t":"eq","v":"0"},{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"true","outputs":5,"x":1259.166648864746,"y":182.50001335144043,"wires":[["8c663d73.7399c"],["4a1e5f84.b5e1a"],["7753f9a2.88ac08"],["1e4aa61b.e1b55a"],["60a0dde4.9f5f24"]]},{"id":"8c663d73.7399c","type":"function","z":"9592163f.6a6de8","name":"presentation","func":"msg.subTypeString = context.global.MYS.SString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1488.916648864746,"y":45.24998474121094,"wires":[["df9e131d.2061f","4d15a037.b2ea6"]]},{"id":"7753f9a2.88ac08","type":"function","z":"9592163f.6a6de8","name":"req","func":"msg.topic = \"req\";\nreturn msg;","outputs":1,"noerr":0,"x":1484.5000228881836,"y":182.75000190734863,"wires":[["4d15a037.b2ea6"]]},{"id":"1e4aa61b.e1b55a","type":"function","z":"9592163f.6a6de8","name":"internal","func":"msg.subTypeString = context.global.MYS.IString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1488.5000228881836,"y":233.00000190734863,"wires":[["df9e131d.2061f","4d15a037.b2ea6","b5e4f17d.4a1b1"]]},{"id":"60a0dde4.9f5f24","type":"function","z":"9592163f.6a6de8","name":"stream","func":"msg.topic = \"stream\";\nreturn msg;","outputs":1,"x":1496.5000228881836,"y":328.00000190734863,"wires":[[]]},{"id":"4d15a037.b2ea6","type":"debug","z":"9592163f.6a6de8","name":"debug","active":false,"console":"false","complete":"true","x":1845.7500267028809,"y":242.00000286102295,"wires":[]},{"id":"4a1e5f84.b5e1a","type":"function","z":"9592163f.6a6de8","name":"set","func":"msg.subTypeString = context.global.MYS.VString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\n\nreturn msg;","outputs":1,"noerr":0,"x":1492.166648864746,"y":107.5,"wires":[["4d15a037.b2ea6","df9e131d.2061f"]]},{"id":"fc54bb91.03ab48","type":"debug","z":"9592163f.6a6de8","name":"","active":false,"console":"false","complete":"true","x":1218.9166259765625,"y":41.66668510437012,"wires":[]},{"id":"6aa2d9f6.955d28","type":"function","z":"9592163f.6a6de8","name":"Split GW Message","func":"\n var tokens = msg.payload.split(\";\")\n \n msg.rawData = tokens;\n if(tokens.length >= 6)\n {\n msg.nodeId = parseInt(tokens[0]);\n msg.childSensorId = parseInt(tokens[1]);\n msg.messageType = parseInt(tokens[2]);\n msg.ack = parseInt(tokens[3]);\n msg.subType = parseInt(tokens[4]);\n msg.payload = tokens[5];\n for (j=6; j<tokens.length; j++) \n msg.payload = msg.payload + ';' + tokens[j];\n }\n\nreturn msg;","outputs":1,"noerr":0,"x":1023.6666488647461,"y":180.66664123535156,"wires":[["e6ce260d.1931d8","fc54bb91.03ab48","e0e76d62.1f189"]]},{"id":"df9e131d.2061f","type":"mqtt out","z":"9592163f.6a6de8","name":"Publish to MQTT","topic":"","qos":"","retain":"","broker":"ba386057.845d3","x":1858.9166526794434,"y":181.16665649414062,"wires":[]},{"id":"b5e4f17d.4a1b1","type":"function","z":"9592163f.6a6de8","name":"hanlde internal messages","func":"//msg.subTypeString = \"\";\n//msg.topic = \"internal respones\";\n\nif (msg.subTypeString == 'I_TIME')\n{\n var payload = parseInt(new Date().getTime()/1000);\n\tvar command = context.global.MYS.T_INTERNAL; \n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_TIME; // I_TIME\n\tmsg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg;\n \n}\nelse if (msg.subTypeString == 'I_ID_REQUEST')\n{\n msg.topic = \"I_ID_RESPONSE\";\n msg.subTypeString = \"I_ID_RESPONSE\";\n // 255;255;3;0;4;8 for ID 8\n var command = context.global.MYS.T_INTERNAL;\n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_ID_RESPONSE; // I_ID_RESPONSE\n\n\tif (context.global.mysnextid[msg.controller] === undefined) {\n\t payload = context.global.MYS.MIN_NODEID;\n\t} \n\telse\n\t{\n\t payload = context.global.mysnextid[msg.controller];\n\t}\n\t\n msg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg; \n} \nelse if (msg.subTypeString == 'I_CONFIG')\n{\n var payload = 'M';\n\tvar command = context.global.MYS.T_INTERNAL; \n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_CONFIG; // I_TIME\n\tmsg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg;\n}\nelse if (msg.subTypeString == 'I_INCLUSION_MODE')\n{\n // not yet implemented\n}\n\nreturn;\n\n\n","outputs":1,"noerr":0,"x":1694.916648864746,"y":543.4166889190674,"wires":[["4d15a037.b2ea6","266b87b3.d99478"]]},{"id":"e6d67f33.19298","type":"inject","z":"9592163f.6a6de8","name":"Startup","topic":"","payload":"","payloadType":"none","repeat":"","crontab":"","once":true,"x":145.25,"y":81.41665363311768,"wires":[["64617800.9b9e88","56b9f6ab.a94608","3e866f6d.c1799"]]},{"id":"ebcef3df.14311","type":"function","z":"9592163f.6a6de8","name":"ToString","func":"msg.payload = msg.payload.toString().replace(/[\\n\\r]/g, '');\n\nreturn msg;","outputs":1,"noerr":0,"x":829.1666946411133,"y":181.91668796539307,"wires":[["6aa2d9f6.955d28"]]},{"id":"31047fa6.cefb8","type":"catch","z":"9592163f.6a6de8","name":"","x":58,"y":449,"wires":[["3622f9b9.c9dd06"]]},{"id":"3622f9b9.c9dd06","type":"debug","z":"9592163f.6a6de8","name":"","active":false,"console":"false","complete":"true","x":224,"y":450,"wires":[]},{"id":"64617800.9b9e88","type":"function","z":"9592163f.6a6de8","name":"MYS Initialize","func":"function MySHelper() { \n\nMySHelper.prototype.TOPIC_PREFIX = \"MYS-NODERED\";\n\nMySHelper.prototype.MIN_NODEID = 10;\n\n\n// don't touch below :)\n \nMySHelper.prototype.T_PRESENTATION = 0;\nMySHelper.prototype.T_SET = 1;\nMySHelper.prototype.T_REQ = 2;\nMySHelper.prototype.T_INTERNAL = 3;\nMySHelper.prototype.T_STREAM = 4;\n\nMySHelper.prototype.I_BATTERY_LEVEL = 0;\nMySHelper.prototype.I_TIME = 1;\nMySHelper.prototype.I_VERSION = 2;\nMySHelper.prototype.I_ID_REQUEST = 3;\nMySHelper.prototype.I_ID_RESPONSE = 4;\nMySHelper.prototype.I_INCLUSION_MODE = 5;\nMySHelper.prototype.I_CONFIG = 6;\nMySHelper.prototype.I_PING = 7;\nMySHelper.prototype.I_PING_ACK = 8;\nMySHelper.prototype.I_LOG_MESSAGE = 9;\nMySHelper.prototype.I_CHILDREN = 10;\nMySHelper.prototype.I_SKETCH_NAME = 11;\nMySHelper.prototype.I_SKETCH_VERSION = 12;\nMySHelper.prototype.I_REBOOT = 13;\nMySHelper.prototype.I_GATEWAY_READY = 14;\nMySHelper.prototype.I_REQUEST_SIGNING = 15;\nMySHelper.prototype.I_GET_NONCE = 16;\nMySHelper.prototype.I_GET_NONCE_RESPONSE = 17;\nMySHelper.prototype.I_HEARTBEAT = 18;\nMySHelper.prototype.I_PRESENTATION = 19;\n \nvar itype = {\nI_BATTERY_LEVEL: MySHelper.prototype.I_BATTERY_LEVEL,\nI_TIME: MySHelper.prototype.I_TIME,\nI_VERSION: MySHelper.prototype.I_VERSION,\nI_ID_REQUEST: MySHelper.prototype.I_ID_REQUEST,\nI_ID_RESPONSE: MySHelper.prototype.I_ID_RESPONSE,\nI_INCLUSION_MODE: MySHelper.prototype.I_INCLUSION_MODE,\nI_CONFIG: MySHelper.prototype.I_CONFIG,\nI_PING: MySHelper.prototype.I_PING,\nI_PING_ACK: MySHelper.prototype.I_PING_ACK,\nI_LOG_MESSAGE: MySHelper.prototype.I_LOG_MESSAGE,\nI_CHILDREN: MySHelper.prototype.I_CHILDREN,\nI_SKETCH_NAME: MySHelper.prototype.I_SKETCH_NAME,\nI_SKETCH_VERSION: MySHelper.prototype.I_SKETCH_VERSION,\nI_REBOOT: MySHelper.prototype.I_REBOOT,\nI_GATEWAY_READY: MySHelper.prototype.I_GATEWAY_READY,\nI_REQUEST_SIGNING: MySHelper.prototype.I_REQUEST_SIGNING,\nI_GET_NONCE: MySHelper.prototype.I_GET_NONCE,\nI_GET_NONCE_RESPONSE: MySHelper.prototype.I_GET_NONCE_RESPONSE,\nI_HEARTBEAT: MySHelper.prototype.I_HEARTBEAT,\nI_PRESENTATION: MySHelper.prototype.I_PRESENTATION\n};\n\nMySHelper.prototype.IString = function(I_SUBTYPE) {\n for (var prop in itype ) \n if( itype[ prop ] === parseInt(I_SUBTYPE) )\n return prop;\n};\n\nMySHelper.prototype.V_TEMP = 0;\nMySHelper.prototype.V_HUM = 1;\nMySHelper.prototype.V_LIGHT = 2;\nMySHelper.prototype.V_STATUS = 2;\nMySHelper.prototype.V_DIMMER = 3;\nMySHelper.prototype.V_PRESSURE = 4;\nMySHelper.prototype.V_FORECAST = 5;\nMySHelper.prototype.V_RAIN = 6;\nMySHelper.prototype.V_RAINRATE = 7;\nMySHelper.prototype.V_WIND = 8;\nMySHelper.prototype.V_GUST = 9;\nMySHelper.prototype.V_DIRECTION = 10;\nMySHelper.prototype.V_UV = 11;\nMySHelper.prototype.V_WEIGHT = 12;\nMySHelper.prototype.V_DISTANCE = 13;\nMySHelper.prototype.V_IMPEDANCE = 14;\nMySHelper.prototype.V_ARMED = 15;\nMySHelper.prototype.V_TRIPPED = 16;\nMySHelper.prototype.V_WATT = 17;\nMySHelper.prototype.V_KWH = 18;\nMySHelper.prototype.V_SCENE_ON = 19;\nMySHelper.prototype.V_SCENE_OFF = 20;\nMySHelper.prototype.V_HEATER = 21;\nMySHelper.prototype.V_HEATER_SW = 22;\nMySHelper.prototype.V_LIGHT_LEVEL = 23;\nMySHelper.prototype.V_VAR1 = 24;\nMySHelper.prototype.V_VAR2 = 25;\nMySHelper.prototype.V_VAR3 = 26;\nMySHelper.prototype.V_VAR4 = 27;\nMySHelper.prototype.V_VAR5 = 28;\nMySHelper.prototype.V_UP = 29;\nMySHelper.prototype.V_DOWN = 30;\nMySHelper.prototype.V_STOP = 31;\nMySHelper.prototype.V_IR_SEND = 32;\nMySHelper.prototype.V_IR_RECEIVE = 33;\nMySHelper.prototype.V_FLOW = 34;\nMySHelper.prototype.V_VOLUME = 35;\nMySHelper.prototype.V_LOCK_STATUS = 36;\nMySHelper.prototype.V_LEVEL = 37; \nMySHelper.prototype.V_VOLTAGE = 38; \nMySHelper.prototype.V_CURRENT = 39; \nMySHelper.prototype.V_RGB = 40; \nMySHelper.prototype.V_RGBW = 41;\nMySHelper.prototype.V_ID = 42;\nMySHelper.prototype.V_UNIT_PREFIX = 43;\nMySHelper.prototype.V_HVAC_SETPOINT_COOL = 44;\nMySHelper.prototype.V_HVAC_SETPOINT_HEAT = 45;\nMySHelper.prototype.V_HVAC_FLOW_MODE = 46;\nMySHelper.prototype.V_TEXT = 47;\n\nvar vtype = {\nV_TEMP: MySHelper.prototype.V_TEMP,\nV_HUM: MySHelper.prototype.V_HUM,\nV_STATUS: MySHelper.prototype.V_STATUS,\nV_LIGHT: MySHelper.prototype.V_LIGHT,\nV_DIMMER: MySHelper.prototype.V_DIMMER,\nV_PRESSURE: MySHelper.prototype.V_PRESSURE,\nV_FORECAST: MySHelper.prototype.V_FORECAST,\nV_RAIN: MySHelper.prototype.V_RAIN,\nV_RAINRATE: MySHelper.prototype.V_RAINRATE,\nV_WIND: MySHelper.prototype.V_WIND,\nV_GUST: MySHelper.prototype.V_GUST,\nV_DIRECTION: MySHelper.prototype.V_DIRECTION,\nV_UV: MySHelper.prototype.V_UV,\nV_WEIGHT: MySHelper.prototype.V_WEIGHT,\nV_DISTANCE: MySHelper.prototype.V_DISTANCE,\nV_IMPEDANCE: MySHelper.prototype.V_IMPEDANCE,\nV_ARMED: MySHelper.prototype.V_ARMED,\nV_TRIPPED: MySHelper.prototype.V_TRIPPED,\nV_WATT: MySHelper.prototype.V_WATT,\nV_KWH: MySHelper.prototype.V_KWH,\nV_SCENE_ON: MySHelper.prototype.V_SCENE_ON,\nV_SCENE_OFF: MySHelper.prototype.V_SCENE_OFF,\nV_HEATER: MySHelper.prototype.V_HEATER,\nV_HEATER_SW: MySHelper.prototype.V_HEATER_SW,\nV_LIGHT_LEVEL: MySHelper.prototype.V_LIGHT_LEVEL,\nV_VAR1: MySHelper.prototype.V_VAR1,\nV_VAR2: MySHelper.prototype.V_VAR2,\nV_VAR3: MySHelper.prototype.V_VAR3,\nV_VAR4: MySHelper.prototype.V_VAR4,\nV_VAR5: MySHelper.prototype.V_VAR5,\nV_UP: MySHelper.prototype.V_UP,\nV_DOWN: MySHelper.prototype.V_DOWN,\nV_STOP: MySHelper.prototype.V_STOP,\nV_IR_SEND: MySHelper.prototype.V_IR_SEND,\nV_IR_RECEIVE: MySHelper.prototype.V_IR_RECEIVE,\nV_FLOW: MySHelper.prototype.V_FLOW,\nV_VOLUME: MySHelper.prototype.V_VOLUME,\nV_LOCK_STATUS: MySHelper.prototype.V_LOCK_STATUS,\nV_LEVEL: MySHelper.prototype.V_LEVEL,\nV_VOLTAGE: MySHelper.prototype.V_VOLTAGE, \nV_CURRENT: MySHelper.prototype.V_CURRENT,\nV_RGB: MySHelper.prototype.V_RGB,\nV_RGBW: MySHelper.prototype.V_RGBW,\nV_ID: MySHelper.prototype.V_ID,\nV_UNIT_PREFIX: MySHelper.prototype.V_UNIT_PREFIX,\nV_HVAC_SETPOINT_COOL:MySHelper.prototype.V_HVAC_SETPOINT_COOL,\nV_HVAC_SETPOINT_HEAT:MySHelper.prototype.V_HVAC_SETPOINT_HEAT,\nV_HVAC_FLOW_MODE: MySHelper.prototype.V_HVAC_FLOW_MODE,\nV_TEXT: MySHelper.prototype.V_TEXT\n};\n\n\n\nMySHelper.prototype.VString = function(V_SUBTYPE) {\n for (var prop in vtype ) \n if( vtype[ prop ] === parseInt(V_SUBTYPE) )\n return prop;\n};\n \nMySHelper.prototype.VNum = function(V_SUBTYPE) {\n sRet = vtype [V_SUBTYPE];\n if (sRet === undefined)\n sRet = V_SUBTYPE;\n return sRet;\n}\n\nMySHelper.prototype.S_DOOR = 0; // Door sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_MOTION = 1; // Motion sensor; V_TRIPPED; V_ARMED \nMySHelper.prototype.S_SMOKE = 2; // Smoke sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_LIGHT = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nMySHelper.prototype.S_BINARY = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nMySHelper.prototype.S_DIMMER = 4; // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nMySHelper.prototype.S_COVER = 5; // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nMySHelper.prototype.S_TEMP = 6; // Temperature sensor; V_TEMP\nMySHelper.prototype.S_HUM = 7; // Humidity sensor; V_HUM\nMySHelper.prototype.S_BARO = 8; // Barometer sensor; V_PRESSURE; V_FORECAST\nMySHelper.prototype.S_WIND = 9; // Wind sensor; V_WIND; V_GUST\nMySHelper.prototype.S_RAIN = 10; // Rain sensor; V_RAIN; V_RAINRATE\nMySHelper.prototype.S_UV = 11; // Uv sensor; V_UV\nMySHelper.prototype.S_WEIGHT = 12; // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nMySHelper.prototype.S_POWER = 13; // Power meter; V_WATT; V_KWH\nMySHelper.prototype.S_HEATER = 14; // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nMySHelper.prototype.S_DISTANCE = 15; // Distance sensor; V_DISTANCE\nMySHelper.prototype.S_LIGHT_LEVEL = 16; // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nMySHelper.prototype.S_ARDUINO_NODE = 17 ; // Used (internally) for presenting a non-repeating Arduino node\nMySHelper.prototype.S_ARDUINO_REPEATER_NODE = 18; // Used (internally) for presenting a repeating Arduino node \nMySHelper.prototype.S_LOCK = 19; // Lock device; V_LOCK_STATUS\nMySHelper.prototype.S_IR = 20; // Ir device; V_IR_SEND; V_IR_RECEIVE\nMySHelper.prototype.S_WATER = 21; // Water meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_AIR_QUALITY = 22; // Air quality sensor; V_LEVEL\nMySHelper.prototype.S_CUSTOM = 23; // Custom sensor \nMySHelper.prototype.S_DUST = 24; // Dust sensor; V_LEVEL\nMySHelper.prototype.S_SCENE_CONTROLLER = 25; // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nMySHelper.prototype.S_RGB_LIGHT = 26; // RGB light. Send color component data using V_RGB. Also supports V_WATT \nMySHelper.prototype.S_RGBW_LIGHT = 27; // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nMySHelper.prototype.S_COLOR_SENSOR = 28; // Color sensor; send color information using V_RGB\nMySHelper.prototype.S_HVAC = 28; // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nMySHelper.prototype.S_MULTIMETER = 29; // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nMySHelper.prototype.S_SPRINKLER = 30; // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nMySHelper.prototype.S_WATER_LEAK = 31; // Water leak sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_SOUND = 32; // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nMySHelper.prototype.S_VIBRATION = 33; // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nMySHelper.prototype.S_MOISTURE = 34; // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nMySHelper.prototype.S_INFO = 35; // LCD text device / Simple information device on controller; V_TEXT\nMySHelper.prototype.S_GAS = 36; // Gas meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_GPS = 37; // GPS Sensor; V_POSITION\n \nvar stype = {\nS_DOOR: MySHelper.prototype.S_DOOR, // Door sensor; V_TRIPPED; V_ARMED\nS_MOTION: MySHelper.prototype.S_MOTION, // Motion sensor; V_TRIPPED; V_ARMED \nS_SMOKE: MySHelper.prototype.S_SMOKE, // Smoke sensor; V_TRIPPED; V_ARMED\nS_LIGHT: MySHelper.prototype.S_LIGHT, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nS_BINARY: MySHelper.prototype.S_BINARY, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nS_DIMMER: MySHelper.prototype.S_DIMMER, // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nS_COVER: MySHelper.prototype.S_COVER, // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nS_TEMP: MySHelper.prototype.S_TEMP, // Temperature sensor; V_TEMP\nS_HUM: MySHelper.prototype.S_HUM, // Humidity sensor; V_HUM\nS_BARO: MySHelper.prototype.S_BARO, // Barometer sensor; V_PRESSURE; V_FORECAST\nS_WIND: MySHelper.prototype.S_WIND, // Wind sensor; V_WIND; V_GUST\nS_RAIN: MySHelper.prototype.S_RAIN, // Rain sensor; V_RAIN; V_RAINRATE\nS_UV: MySHelper.prototype.S_UV, // Uv sensor; V_UV\nS_WEIGHT: MySHelper.prototype.S_WEIGHT, // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nS_POWER: MySHelper.prototype.S_POWER, // Power meter; V_WATT; V_KWH\nS_HEATER: MySHelper.prototype.S_HEATER, // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nS_DISTANCE: MySHelper.prototype.S_DISTANCE, // Distance sensor; V_DISTANCE\nS_LIGHT_LEVEL: MySHelper.prototype.S_LIGHT_LEVEL, // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nS_ARDUINO_NODE: MySHelper.prototype.S_ARDUINO_NODE, // Used (internally) for presenting a non-repeating Arduino node\nS_ARDUINO_REPEATER_NODE:MySHelper.prototype.S_ARDUINO_REPEATER_NODE, // Used (internally) for presenting a repeating Arduino node \nS_LOCK: MySHelper.prototype.S_LOCK, // Lock device; V_LOCK_STATUS\nS_IR: MySHelper.prototype.S_IR, // Ir device; V_IR_SEND; V_IR_RECEIVE\nS_WATER: MySHelper.prototype.S_WATER, // Water meter; V_FLOW; V_VOLUME\nS_AIR_QUALITY: MySHelper.prototype.S_AIR_QUALITY, // Air quality sensor; V_LEVEL\nS_CUSTOM: MySHelper.prototype.S_CUSTOM, // Custom sensor \nS_DUST: MySHelper.prototype.S_DUST, // Dust sensor; V_LEVEL\nS_SCENE_CONTROLLER: MySHelper.prototype.S_SCENE_CONTROLLER, // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nS_RGB_LIGHT: MySHelper.prototype.S_RGB_LIGHT, // RGB light. Send color component data using V_RGB. Also supports V_WATT \nS_RGBW_LIGHT: MySHelper.prototype.S_RGBW_LIGHT, // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nS_COLOR_SENSOR: MySHelper.prototype.S_COLOR_SENSOR, // Color sensor; send color information using V_RGB\nS_HVAC: MySHelper.prototype.S_HVAC, // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nS_MULTIMETER: MySHelper.prototype.S_MULTIMETER, // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nS_SPRINKLER: MySHelper.prototype.S_SPRINKLER, // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nS_WATER_LEAK: MySHelper.prototype.S_WATER_LEAK, // Water leak sensor; V_TRIPPED; V_ARMED\nS_SOUND: MySHelper.prototype.S_SOUND, // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nS_VIBRATION: MySHelper.prototype.S_VIBRATION, // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nS_MOISTURE: MySHelper.prototype.S_MOISTURE, // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nS_INFO: MySHelper.prototype.S_INFO, // LCD text device / Simple information device on controller; V_TEXT\nS_GAS: MySHelper.prototype.S_GAS, // Gas meter; V_FLOW; V_VOLUME\nS_GPS: MySHelper.prototype.S_GPS // GPS Sensor; V_POSITION\n};\n\nMySHelper.prototype.SString = function(S_SUBTYPE) {\n for (var prop in stype ) \n if( stype[ prop ] === parseInt(S_SUBTYPE) )\n return prop;\n}; \n \n MySHelper.prototype.encode = function(destination, sensor, command, acknowledge, type, payload) {\n\tvar msg = destination.toString(10) + \";\" + sensor.toString(10) + \";\" + command.toString(10) + \";\" + acknowledge.toString(10) + \";\" + type.toString(10) + \";\";\n\tif (command == 4) {\n\t\tfor (var i = 0; i < payload.length; i++) {\n\t\t\tif (payload[i] < 16)\n\t\t\t\tmsg += \"0\";\n\t\t\tmsg += payload[i].toString(16);\n\t\t}\n\t} else {\n\t\tmsg += payload;\n\t}\n\tmsg += '\\n';\n\treturn msg.toString();\n}\n}\n\n\nvar MySHelperObj = new MySHelper();\n\ncontext.global.MYS = MySHelperObj;\n\nreturn msg;","outputs":1,"noerr":0,"x":383.25,"y":20,"wires":[[]]},{"id":"df1e322.f20e1d","type":"function","z":"9592163f.6a6de8","name":"Set Controller 1","func":"msg.controller = 1\n\nreturn msg;","outputs":1,"noerr":0,"x":641.0000076293945,"y":147.49999809265137,"wires":[["ebcef3df.14311"]]},{"id":"266b87b3.d99478","type":"switch","z":"9592163f.6a6de8","name":"route to controller n","property":"controller","rules":[{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"false","outputs":4,"x":133,"y":214.25,"wires":[["3e866f6d.c1799"],["c7d0d88b.382f28"],[],[]]},{"id":"c7d0d88b.382f28","type":"tcp request","z":"9592163f.6a6de8","server":"192.168.92.14","port":"5003","out":"sit","splitc":"0","name":"MySWifi ESP8266 GW AES 14","x":410.5,"y":207.24999618530273,"wires":[["c5f14d8f.3a0eb"]]},{"id":"c5f14d8f.3a0eb","type":"function","z":"9592163f.6a6de8","name":"Set Controller 2","func":"msg.controller = 2\n\nreturn msg;","outputs":1,"noerr":0,"x":653.5,"y":205.7500114440918,"wires":[["ebcef3df.14311"]]},{"id":"56b9f6ab.a94608","type":"file in","z":"9592163f.6a6de8","name":"read store for next ids","filename":"mysids.dump","format":"utf8","x":395,"y":65,"wires":[["57db23d6.a824dc"]]},{"id":"e000bd09.1fff4","type":"debug","z":"9592163f.6a6de8","name":"Debug","active":false,"console":"false","complete":"true","x":732,"y":361,"wires":[]},{"id":"57db23d6.a824dc","type":"function","z":"9592163f.6a6de8","name":"store to context.global.mysnextid","func":"if (msg.payload === undefined) {\n var mysnextid = {};\n\n obj = mysnextid; \n}\nelse \n{\ntry{\n obj = JSON.parse(msg.payload);\n }\n catch(e){\n \n var mysnextid = {};\n\n obj = mysnextid;\n \n }\n} \n\ncontext.global.mysnextid = obj;\n\nmsg.payload = context.global.mysnextid;\n\nreturn msg;","outputs":1,"noerr":0,"x":658,"y":53,"wires":[[]]},{"id":"dfba7d69.20458","type":"file","z":"9592163f.6a6de8","name":"dump mysids","filename":"mysids.dump","appendNewline":true,"createDir":false,"overwriteFile":"true","x":1473,"y":381.99999618530273,"wires":[]},{"id":"e0e76d62.1f189","type":"function","z":"9592163f.6a6de8","name":"handle nextids","func":"// increase nextid, if nodeid >= nextid \n// node.log(\"Handling next ids\");\n// node.log(\"nodeId: \" + msg.nodeId);\n\nbChanged = false;\n\nif (msg.nodeId === 0) return;\n\nif (msg.nodeId < 255)\n{\n // node.log(\"Test if next node-id must be set\");\n if (context.global.mysnextid[msg.controller] === undefined) {\n node.log(\"node-id not initialized yet\");\n context.global.mysnextid[msg.controller] = msg.nodeId+1;\n if (context.global.mysnextid[msg.controller] < context.global.MYS.MIN_NODEID)\n context.global.mysnextid[msg.controller] = context.global.MYS.MIN_NODEID;\n bChanged = true;\n }\n \n // node.log(\"Nexid stored \" + parseInt(context.global.mysnextid[msg.controller]));\n \n if (msg.nodeId >= parseInt(context.global.mysnextid[msg.controller])) {\n node.log(\"node-id >= next -> increase\");\n // convert to int\n context.global.mysnextid[msg.controller] = parseInt(context.global.mysnextid[msg.controller]);\n context.global.mysnextid[msg.controller] = msg.nodeId+1; \n if (context.global.mysnextid[msg.controller] < context.global.MYS.MIN_NODEID)\n context.global.mysnextid[msg.controller] = context.global.MYS.MIN_NODEID;\n bChanged = true;\n }\n\n if (bChanged) {\n node.log(\"next id must be stored\");\n msg.payload = JSON.stringify(context.global.mysnextid); \n return msg;\n }\n}\n\n\n","outputs":1,"noerr":0,"x":1262,"y":374.99999618530273,"wires":[["dfba7d69.20458","5c074c19.a3f8b4"]]},{"id":"8da09002.725f7","type":"function","z":"9592163f.6a6de8","name":"MQTT to MYS convert","func":"// topic = MYS-NODERED/set/controller/node-id/sensor-id/ack/sub-type\n// payload = payload :)\n\n var tokens = msg.topic.split(\"/\");\n \n msg.rawData = tokens;\n msg.tokens = tokens.length;\n if(tokens.length == 7)\n {\n if (tokens[0] != context.global.MYS.TOPIC_PREFIX) // not for us\n return;\n if (tokens[1] != 'set') // not for us\n return;\n \n msg.controller = parseInt(tokens[2]);\n msg.messageType = context.global.MYS.T_SET;\n msg.nodeId = parseInt(tokens[3]);\n msg.childSensorId = parseInt(tokens[4]);\n msg.ack = parseInt(tokens[5]);\n msg.subType = context.global.MYS.VNum(tokens[6]);\n \n msg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, msg.messageType, msg.ack, msg.subType, msg.payload);\n \n return msg; \n }\n","outputs":1,"noerr":0,"x":490,"y":361,"wires":[["e000bd09.1fff4","266b87b3.d99478"]]},{"id":"3e866f6d.c1799","type":"tcp request","z":"9592163f.6a6de8","server":"192.168.92.13","port":"5003","out":"sit","splitc":"0","name":"MySWifi ESP8266 GW AES 13","x":407,"y":145.99999618530273,"wires":[["df1e322.f20e1d","9386fdb0.6c79"]]},{"id":"5c074c19.a3f8b4","type":"debug","z":"9592163f.6a6de8","name":"","active":true,"console":"false","complete":"false","x":1454,"y":543.9999961853027,"wires":[]},{"id":"c75fd7f4.38a028","type":"mqtt in","z":"9592163f.6a6de8","name":"Read MQTT Stream: change Topic to your needs","topic":"MYS-NODERED/set/#","broker":"ba386057.845d3","x":183.5,"y":362,"wires":[["8da09002.725f7"]]},{"id":"9386fdb0.6c79","type":"function","z":"9592163f.6a6de8","name":"Watchdog controller 1","func":"if (isNaN(context.global.controller1count))\n context.global.controller1count=0;\n\n\ncontext.global.controller1count++;\n\n","outputs":1,"noerr":0,"x":630,"y":105,"wires":[[]]},{"id":"d465a67.f2b9a58","type":"inject","z":"9592163f.6a6de8","name":"Check health controller 1 every 5 minutes","topic":"","payload":"","payloadType":"none","repeat":"60","crontab":"","once":false,"x":173,"y":516,"wires":[["aa935a.ff556ca8"]]},{"id":"aa935a.ff556ca8","type":"function","z":"9592163f.6a6de8","name":"check health controlller 1","func":"if (isNaN(context.global.controller1count))\n context.global.controller1count=0;\n \nif (context.global.controller1count === 0) {\n // make a new connection to the controller\n msg.payload = \"\";\n node.log(\"no message recieved on mys controller 1, try to connect\");\n \n return msg;\n}\nelse\n{\n // reset counter\n context.global.controller1count=0;\n}\n","outputs":1,"noerr":0,"x":470,"y":510,"wires":[["c8b342e9.374cc","3e866f6d.c1799"]]},{"id":"c8b342e9.374cc","type":"debug","z":"9592163f.6a6de8","name":"","active":true,"console":"false","complete":"false","x":682,"y":511,"wires":[]}]``` -
- Fixed node-id handling for new nodes.
- added write support (see "MQTT to MYS" convert for details)
- parameters can be set in 'MYS initialize'
[{"id":"ba386057.845d3","type":"mqtt-broker","broker":"192.168.92.4","port":"1883","clientid":"NodeRed"},{"id":"e6ce260d.1931d8","type":"switch","z":"9592163f.6a6de8","name":"switch message type","property":"messageType","rules":[{"t":"eq","v":"0"},{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"true","outputs":5,"x":1259.166648864746,"y":182.50001335144043,"wires":[["8c663d73.7399c"],["4a1e5f84.b5e1a"],["7753f9a2.88ac08"],["1e4aa61b.e1b55a"],["60a0dde4.9f5f24"]]},{"id":"8c663d73.7399c","type":"function","z":"9592163f.6a6de8","name":"presentation","func":"msg.subTypeString = context.global.MYS.SString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1488.916648864746,"y":45.24998474121094,"wires":[["df9e131d.2061f","4d15a037.b2ea6"]]},{"id":"7753f9a2.88ac08","type":"function","z":"9592163f.6a6de8","name":"req","func":"msg.topic = \"req\";\nreturn msg;","outputs":1,"noerr":0,"x":1484.5000228881836,"y":182.75000190734863,"wires":[["4d15a037.b2ea6"]]},{"id":"1e4aa61b.e1b55a","type":"function","z":"9592163f.6a6de8","name":"internal","func":"msg.subTypeString = context.global.MYS.IString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1488.5000228881836,"y":233.00000190734863,"wires":[["df9e131d.2061f","4d15a037.b2ea6","b5e4f17d.4a1b1"]]},{"id":"60a0dde4.9f5f24","type":"function","z":"9592163f.6a6de8","name":"stream","func":"msg.topic = \"stream\";\nreturn msg;","outputs":1,"x":1496.5000228881836,"y":328.00000190734863,"wires":[[]]},{"id":"4d15a037.b2ea6","type":"debug","z":"9592163f.6a6de8","name":"debug","active":false,"console":"false","complete":"true","x":1845.7500267028809,"y":242.00000286102295,"wires":[]},{"id":"4a1e5f84.b5e1a","type":"function","z":"9592163f.6a6de8","name":"set","func":"msg.subTypeString = context.global.MYS.VString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\n\nreturn msg;","outputs":1,"noerr":0,"x":1492.166648864746,"y":107.5,"wires":[["4d15a037.b2ea6","df9e131d.2061f"]]},{"id":"fc54bb91.03ab48","type":"debug","z":"9592163f.6a6de8","name":"","active":false,"console":"false","complete":"true","x":1218.9166259765625,"y":41.66668510437012,"wires":[]},{"id":"6aa2d9f6.955d28","type":"function","z":"9592163f.6a6de8","name":"Split GW Message","func":"\n var tokens = msg.payload.split(\";\")\n \n msg.rawData = tokens;\n if(tokens.length >= 6)\n {\n msg.nodeId = parseInt(tokens[0]);\n msg.childSensorId = parseInt(tokens[1]);\n msg.messageType = parseInt(tokens[2]);\n msg.ack = parseInt(tokens[3]);\n msg.subType = parseInt(tokens[4]);\n msg.payload = tokens[5];\n for (j=6; j<tokens.length; j++) \n msg.payload = msg.payload + ';' + tokens[j];\n }\n\nreturn msg;","outputs":1,"noerr":0,"x":1023.6666488647461,"y":180.66664123535156,"wires":[["e6ce260d.1931d8","fc54bb91.03ab48","e0e76d62.1f189"]]},{"id":"df9e131d.2061f","type":"mqtt out","z":"9592163f.6a6de8","name":"Publish to MQTT","topic":"","qos":"","retain":"","broker":"ba386057.845d3","x":1858.9166526794434,"y":181.16665649414062,"wires":[]},{"id":"b5e4f17d.4a1b1","type":"function","z":"9592163f.6a6de8","name":"hanlde internal messages","func":"//msg.subTypeString = \"\";\n//msg.topic = \"internal respones\";\n\nif (msg.subTypeString == 'I_TIME')\n{\n var payload = parseInt(new Date().getTime()/1000);\n\tvar command = context.global.MYS.T_INTERNAL; \n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_TIME; // I_TIME\n\tmsg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg;\n \n}\nelse if (msg.subTypeString == 'I_ID_REQUEST')\n{\n msg.topic = \"I_ID_RESPONSE\";\n msg.subTypeString = \"I_ID_RESPONSE\";\n // 255;255;3;0;4;8 for ID 8\n var command = context.global.MYS.T_INTERNAL;\n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_ID_RESPONSE; // I_ID_RESPONSE\n\n\tif (context.global.mysnextid[msg.controller] === undefined) {\n\t payload = context.global.MYS.MIN_NODEID;\n\t} \n\telse\n\t{\n\t payload = context.global.mysnextid[msg.controller];\n\t}\n\t\n msg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg; \n} \nelse if (msg.subTypeString == 'I_CONFIG')\n{\n var payload = 'M';\n\tvar command = context.global.MYS.T_INTERNAL; \n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_CONFIG; // I_TIME\n\tmsg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg;\n}\nelse if (msg.subTypeString == 'I_INCLUSION_MODE')\n{\n // not yet implemented\n}\n\nreturn;\n\n\n","outputs":1,"noerr":0,"x":1694.916648864746,"y":543.4166889190674,"wires":[["4d15a037.b2ea6","266b87b3.d99478"]]},{"id":"e6d67f33.19298","type":"inject","z":"9592163f.6a6de8","name":"Startup","topic":"","payload":"","payloadType":"none","repeat":"","crontab":"","once":true,"x":145.25,"y":81.41665363311768,"wires":[["64617800.9b9e88","56b9f6ab.a94608","3e866f6d.c1799"]]},{"id":"ebcef3df.14311","type":"function","z":"9592163f.6a6de8","name":"ToString","func":"msg.payload = msg.payload.toString().replace(/[\\n\\r]/g, '');\n\nreturn msg;","outputs":1,"noerr":0,"x":829.1666946411133,"y":181.91668796539307,"wires":[["6aa2d9f6.955d28"]]},{"id":"31047fa6.cefb8","type":"catch","z":"9592163f.6a6de8","name":"","x":58,"y":449,"wires":[["3622f9b9.c9dd06"]]},{"id":"3622f9b9.c9dd06","type":"debug","z":"9592163f.6a6de8","name":"","active":false,"console":"false","complete":"true","x":224,"y":450,"wires":[]},{"id":"64617800.9b9e88","type":"function","z":"9592163f.6a6de8","name":"MYS Initialize","func":"function MySHelper() { \n\nMySHelper.prototype.TOPIC_PREFIX = \"MYS-NODERED\";\n\nMySHelper.prototype.MIN_NODEID = 10;\n\n\n// don't touch below :)\n \nMySHelper.prototype.T_PRESENTATION = 0;\nMySHelper.prototype.T_SET = 1;\nMySHelper.prototype.T_REQ = 2;\nMySHelper.prototype.T_INTERNAL = 3;\nMySHelper.prototype.T_STREAM = 4;\n\nMySHelper.prototype.I_BATTERY_LEVEL = 0;\nMySHelper.prototype.I_TIME = 1;\nMySHelper.prototype.I_VERSION = 2;\nMySHelper.prototype.I_ID_REQUEST = 3;\nMySHelper.prototype.I_ID_RESPONSE = 4;\nMySHelper.prototype.I_INCLUSION_MODE = 5;\nMySHelper.prototype.I_CONFIG = 6;\nMySHelper.prototype.I_PING = 7;\nMySHelper.prototype.I_PING_ACK = 8;\nMySHelper.prototype.I_LOG_MESSAGE = 9;\nMySHelper.prototype.I_CHILDREN = 10;\nMySHelper.prototype.I_SKETCH_NAME = 11;\nMySHelper.prototype.I_SKETCH_VERSION = 12;\nMySHelper.prototype.I_REBOOT = 13;\nMySHelper.prototype.I_GATEWAY_READY = 14;\nMySHelper.prototype.I_REQUEST_SIGNING = 15;\nMySHelper.prototype.I_GET_NONCE = 16;\nMySHelper.prototype.I_GET_NONCE_RESPONSE = 17;\nMySHelper.prototype.I_HEARTBEAT = 18;\nMySHelper.prototype.I_PRESENTATION = 19;\n \nvar itype = {\nI_BATTERY_LEVEL: MySHelper.prototype.I_BATTERY_LEVEL,\nI_TIME: MySHelper.prototype.I_TIME,\nI_VERSION: MySHelper.prototype.I_VERSION,\nI_ID_REQUEST: MySHelper.prototype.I_ID_REQUEST,\nI_ID_RESPONSE: MySHelper.prototype.I_ID_RESPONSE,\nI_INCLUSION_MODE: MySHelper.prototype.I_INCLUSION_MODE,\nI_CONFIG: MySHelper.prototype.I_CONFIG,\nI_PING: MySHelper.prototype.I_PING,\nI_PING_ACK: MySHelper.prototype.I_PING_ACK,\nI_LOG_MESSAGE: MySHelper.prototype.I_LOG_MESSAGE,\nI_CHILDREN: MySHelper.prototype.I_CHILDREN,\nI_SKETCH_NAME: MySHelper.prototype.I_SKETCH_NAME,\nI_SKETCH_VERSION: MySHelper.prototype.I_SKETCH_VERSION,\nI_REBOOT: MySHelper.prototype.I_REBOOT,\nI_GATEWAY_READY: MySHelper.prototype.I_GATEWAY_READY,\nI_REQUEST_SIGNING: MySHelper.prototype.I_REQUEST_SIGNING,\nI_GET_NONCE: MySHelper.prototype.I_GET_NONCE,\nI_GET_NONCE_RESPONSE: MySHelper.prototype.I_GET_NONCE_RESPONSE,\nI_HEARTBEAT: MySHelper.prototype.I_HEARTBEAT,\nI_PRESENTATION: MySHelper.prototype.I_PRESENTATION\n};\n\nMySHelper.prototype.IString = function(I_SUBTYPE) {\n for (var prop in itype ) \n if( itype[ prop ] === parseInt(I_SUBTYPE) )\n return prop;\n};\n\nMySHelper.prototype.V_TEMP = 0;\nMySHelper.prototype.V_HUM = 1;\nMySHelper.prototype.V_LIGHT = 2;\nMySHelper.prototype.V_STATUS = 2;\nMySHelper.prototype.V_DIMMER = 3;\nMySHelper.prototype.V_PRESSURE = 4;\nMySHelper.prototype.V_FORECAST = 5;\nMySHelper.prototype.V_RAIN = 6;\nMySHelper.prototype.V_RAINRATE = 7;\nMySHelper.prototype.V_WIND = 8;\nMySHelper.prototype.V_GUST = 9;\nMySHelper.prototype.V_DIRECTION = 10;\nMySHelper.prototype.V_UV = 11;\nMySHelper.prototype.V_WEIGHT = 12;\nMySHelper.prototype.V_DISTANCE = 13;\nMySHelper.prototype.V_IMPEDANCE = 14;\nMySHelper.prototype.V_ARMED = 15;\nMySHelper.prototype.V_TRIPPED = 16;\nMySHelper.prototype.V_WATT = 17;\nMySHelper.prototype.V_KWH = 18;\nMySHelper.prototype.V_SCENE_ON = 19;\nMySHelper.prototype.V_SCENE_OFF = 20;\nMySHelper.prototype.V_HEATER = 21;\nMySHelper.prototype.V_HEATER_SW = 22;\nMySHelper.prototype.V_LIGHT_LEVEL = 23;\nMySHelper.prototype.V_VAR1 = 24;\nMySHelper.prototype.V_VAR2 = 25;\nMySHelper.prototype.V_VAR3 = 26;\nMySHelper.prototype.V_VAR4 = 27;\nMySHelper.prototype.V_VAR5 = 28;\nMySHelper.prototype.V_UP = 29;\nMySHelper.prototype.V_DOWN = 30;\nMySHelper.prototype.V_STOP = 31;\nMySHelper.prototype.V_IR_SEND = 32;\nMySHelper.prototype.V_IR_RECEIVE = 33;\nMySHelper.prototype.V_FLOW = 34;\nMySHelper.prototype.V_VOLUME = 35;\nMySHelper.prototype.V_LOCK_STATUS = 36;\nMySHelper.prototype.V_LEVEL = 37; \nMySHelper.prototype.V_VOLTAGE = 38; \nMySHelper.prototype.V_CURRENT = 39; \nMySHelper.prototype.V_RGB = 40; \nMySHelper.prototype.V_RGBW = 41;\nMySHelper.prototype.V_ID = 42;\nMySHelper.prototype.V_UNIT_PREFIX = 43;\nMySHelper.prototype.V_HVAC_SETPOINT_COOL = 44;\nMySHelper.prototype.V_HVAC_SETPOINT_HEAT = 45;\nMySHelper.prototype.V_HVAC_FLOW_MODE = 46;\nMySHelper.prototype.V_TEXT = 47;\n\nvar vtype = {\nV_TEMP: MySHelper.prototype.V_TEMP,\nV_HUM: MySHelper.prototype.V_HUM,\nV_STATUS: MySHelper.prototype.V_STATUS,\nV_LIGHT: MySHelper.prototype.V_LIGHT,\nV_DIMMER: MySHelper.prototype.V_DIMMER,\nV_PRESSURE: MySHelper.prototype.V_PRESSURE,\nV_FORECAST: MySHelper.prototype.V_FORECAST,\nV_RAIN: MySHelper.prototype.V_RAIN,\nV_RAINRATE: MySHelper.prototype.V_RAINRATE,\nV_WIND: MySHelper.prototype.V_WIND,\nV_GUST: MySHelper.prototype.V_GUST,\nV_DIRECTION: MySHelper.prototype.V_DIRECTION,\nV_UV: MySHelper.prototype.V_UV,\nV_WEIGHT: MySHelper.prototype.V_WEIGHT,\nV_DISTANCE: MySHelper.prototype.V_DISTANCE,\nV_IMPEDANCE: MySHelper.prototype.V_IMPEDANCE,\nV_ARMED: MySHelper.prototype.V_ARMED,\nV_TRIPPED: MySHelper.prototype.V_TRIPPED,\nV_WATT: MySHelper.prototype.V_WATT,\nV_KWH: MySHelper.prototype.V_KWH,\nV_SCENE_ON: MySHelper.prototype.V_SCENE_ON,\nV_SCENE_OFF: MySHelper.prototype.V_SCENE_OFF,\nV_HEATER: MySHelper.prototype.V_HEATER,\nV_HEATER_SW: MySHelper.prototype.V_HEATER_SW,\nV_LIGHT_LEVEL: MySHelper.prototype.V_LIGHT_LEVEL,\nV_VAR1: MySHelper.prototype.V_VAR1,\nV_VAR2: MySHelper.prototype.V_VAR2,\nV_VAR3: MySHelper.prototype.V_VAR3,\nV_VAR4: MySHelper.prototype.V_VAR4,\nV_VAR5: MySHelper.prototype.V_VAR5,\nV_UP: MySHelper.prototype.V_UP,\nV_DOWN: MySHelper.prototype.V_DOWN,\nV_STOP: MySHelper.prototype.V_STOP,\nV_IR_SEND: MySHelper.prototype.V_IR_SEND,\nV_IR_RECEIVE: MySHelper.prototype.V_IR_RECEIVE,\nV_FLOW: MySHelper.prototype.V_FLOW,\nV_VOLUME: MySHelper.prototype.V_VOLUME,\nV_LOCK_STATUS: MySHelper.prototype.V_LOCK_STATUS,\nV_LEVEL: MySHelper.prototype.V_LEVEL,\nV_VOLTAGE: MySHelper.prototype.V_VOLTAGE, \nV_CURRENT: MySHelper.prototype.V_CURRENT,\nV_RGB: MySHelper.prototype.V_RGB,\nV_RGBW: MySHelper.prototype.V_RGBW,\nV_ID: MySHelper.prototype.V_ID,\nV_UNIT_PREFIX: MySHelper.prototype.V_UNIT_PREFIX,\nV_HVAC_SETPOINT_COOL:MySHelper.prototype.V_HVAC_SETPOINT_COOL,\nV_HVAC_SETPOINT_HEAT:MySHelper.prototype.V_HVAC_SETPOINT_HEAT,\nV_HVAC_FLOW_MODE: MySHelper.prototype.V_HVAC_FLOW_MODE,\nV_TEXT: MySHelper.prototype.V_TEXT\n};\n\n\n\nMySHelper.prototype.VString = function(V_SUBTYPE) {\n for (var prop in vtype ) \n if( vtype[ prop ] === parseInt(V_SUBTYPE) )\n return prop;\n};\n \nMySHelper.prototype.VNum = function(V_SUBTYPE) {\n sRet = vtype [V_SUBTYPE];\n if (sRet === undefined)\n sRet = V_SUBTYPE;\n return sRet;\n}\n\nMySHelper.prototype.S_DOOR = 0; // Door sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_MOTION = 1; // Motion sensor; V_TRIPPED; V_ARMED \nMySHelper.prototype.S_SMOKE = 2; // Smoke sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_LIGHT = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nMySHelper.prototype.S_BINARY = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nMySHelper.prototype.S_DIMMER = 4; // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nMySHelper.prototype.S_COVER = 5; // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nMySHelper.prototype.S_TEMP = 6; // Temperature sensor; V_TEMP\nMySHelper.prototype.S_HUM = 7; // Humidity sensor; V_HUM\nMySHelper.prototype.S_BARO = 8; // Barometer sensor; V_PRESSURE; V_FORECAST\nMySHelper.prototype.S_WIND = 9; // Wind sensor; V_WIND; V_GUST\nMySHelper.prototype.S_RAIN = 10; // Rain sensor; V_RAIN; V_RAINRATE\nMySHelper.prototype.S_UV = 11; // Uv sensor; V_UV\nMySHelper.prototype.S_WEIGHT = 12; // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nMySHelper.prototype.S_POWER = 13; // Power meter; V_WATT; V_KWH\nMySHelper.prototype.S_HEATER = 14; // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nMySHelper.prototype.S_DISTANCE = 15; // Distance sensor; V_DISTANCE\nMySHelper.prototype.S_LIGHT_LEVEL = 16; // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nMySHelper.prototype.S_ARDUINO_NODE = 17 ; // Used (internally) for presenting a non-repeating Arduino node\nMySHelper.prototype.S_ARDUINO_REPEATER_NODE = 18; // Used (internally) for presenting a repeating Arduino node \nMySHelper.prototype.S_LOCK = 19; // Lock device; V_LOCK_STATUS\nMySHelper.prototype.S_IR = 20; // Ir device; V_IR_SEND; V_IR_RECEIVE\nMySHelper.prototype.S_WATER = 21; // Water meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_AIR_QUALITY = 22; // Air quality sensor; V_LEVEL\nMySHelper.prototype.S_CUSTOM = 23; // Custom sensor \nMySHelper.prototype.S_DUST = 24; // Dust sensor; V_LEVEL\nMySHelper.prototype.S_SCENE_CONTROLLER = 25; // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nMySHelper.prototype.S_RGB_LIGHT = 26; // RGB light. Send color component data using V_RGB. Also supports V_WATT \nMySHelper.prototype.S_RGBW_LIGHT = 27; // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nMySHelper.prototype.S_COLOR_SENSOR = 28; // Color sensor; send color information using V_RGB\nMySHelper.prototype.S_HVAC = 28; // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nMySHelper.prototype.S_MULTIMETER = 29; // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nMySHelper.prototype.S_SPRINKLER = 30; // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nMySHelper.prototype.S_WATER_LEAK = 31; // Water leak sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_SOUND = 32; // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nMySHelper.prototype.S_VIBRATION = 33; // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nMySHelper.prototype.S_MOISTURE = 34; // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nMySHelper.prototype.S_INFO = 35; // LCD text device / Simple information device on controller; V_TEXT\nMySHelper.prototype.S_GAS = 36; // Gas meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_GPS = 37; // GPS Sensor; V_POSITION\n \nvar stype = {\nS_DOOR: MySHelper.prototype.S_DOOR, // Door sensor; V_TRIPPED; V_ARMED\nS_MOTION: MySHelper.prototype.S_MOTION, // Motion sensor; V_TRIPPED; V_ARMED \nS_SMOKE: MySHelper.prototype.S_SMOKE, // Smoke sensor; V_TRIPPED; V_ARMED\nS_LIGHT: MySHelper.prototype.S_LIGHT, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nS_BINARY: MySHelper.prototype.S_BINARY, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nS_DIMMER: MySHelper.prototype.S_DIMMER, // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nS_COVER: MySHelper.prototype.S_COVER, // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nS_TEMP: MySHelper.prototype.S_TEMP, // Temperature sensor; V_TEMP\nS_HUM: MySHelper.prototype.S_HUM, // Humidity sensor; V_HUM\nS_BARO: MySHelper.prototype.S_BARO, // Barometer sensor; V_PRESSURE; V_FORECAST\nS_WIND: MySHelper.prototype.S_WIND, // Wind sensor; V_WIND; V_GUST\nS_RAIN: MySHelper.prototype.S_RAIN, // Rain sensor; V_RAIN; V_RAINRATE\nS_UV: MySHelper.prototype.S_UV, // Uv sensor; V_UV\nS_WEIGHT: MySHelper.prototype.S_WEIGHT, // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nS_POWER: MySHelper.prototype.S_POWER, // Power meter; V_WATT; V_KWH\nS_HEATER: MySHelper.prototype.S_HEATER, // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nS_DISTANCE: MySHelper.prototype.S_DISTANCE, // Distance sensor; V_DISTANCE\nS_LIGHT_LEVEL: MySHelper.prototype.S_LIGHT_LEVEL, // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nS_ARDUINO_NODE: MySHelper.prototype.S_ARDUINO_NODE, // Used (internally) for presenting a non-repeating Arduino node\nS_ARDUINO_REPEATER_NODE:MySHelper.prototype.S_ARDUINO_REPEATER_NODE, // Used (internally) for presenting a repeating Arduino node \nS_LOCK: MySHelper.prototype.S_LOCK, // Lock device; V_LOCK_STATUS\nS_IR: MySHelper.prototype.S_IR, // Ir device; V_IR_SEND; V_IR_RECEIVE\nS_WATER: MySHelper.prototype.S_WATER, // Water meter; V_FLOW; V_VOLUME\nS_AIR_QUALITY: MySHelper.prototype.S_AIR_QUALITY, // Air quality sensor; V_LEVEL\nS_CUSTOM: MySHelper.prototype.S_CUSTOM, // Custom sensor \nS_DUST: MySHelper.prototype.S_DUST, // Dust sensor; V_LEVEL\nS_SCENE_CONTROLLER: MySHelper.prototype.S_SCENE_CONTROLLER, // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nS_RGB_LIGHT: MySHelper.prototype.S_RGB_LIGHT, // RGB light. Send color component data using V_RGB. Also supports V_WATT \nS_RGBW_LIGHT: MySHelper.prototype.S_RGBW_LIGHT, // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nS_COLOR_SENSOR: MySHelper.prototype.S_COLOR_SENSOR, // Color sensor; send color information using V_RGB\nS_HVAC: MySHelper.prototype.S_HVAC, // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nS_MULTIMETER: MySHelper.prototype.S_MULTIMETER, // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nS_SPRINKLER: MySHelper.prototype.S_SPRINKLER, // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nS_WATER_LEAK: MySHelper.prototype.S_WATER_LEAK, // Water leak sensor; V_TRIPPED; V_ARMED\nS_SOUND: MySHelper.prototype.S_SOUND, // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nS_VIBRATION: MySHelper.prototype.S_VIBRATION, // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nS_MOISTURE: MySHelper.prototype.S_MOISTURE, // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nS_INFO: MySHelper.prototype.S_INFO, // LCD text device / Simple information device on controller; V_TEXT\nS_GAS: MySHelper.prototype.S_GAS, // Gas meter; V_FLOW; V_VOLUME\nS_GPS: MySHelper.prototype.S_GPS // GPS Sensor; V_POSITION\n};\n\nMySHelper.prototype.SString = function(S_SUBTYPE) {\n for (var prop in stype ) \n if( stype[ prop ] === parseInt(S_SUBTYPE) )\n return prop;\n}; \n \n MySHelper.prototype.encode = function(destination, sensor, command, acknowledge, type, payload) {\n\tvar msg = destination.toString(10) + \";\" + sensor.toString(10) + \";\" + command.toString(10) + \";\" + acknowledge.toString(10) + \";\" + type.toString(10) + \";\";\n\tif (command == 4) {\n\t\tfor (var i = 0; i < payload.length; i++) {\n\t\t\tif (payload[i] < 16)\n\t\t\t\tmsg += \"0\";\n\t\t\tmsg += payload[i].toString(16);\n\t\t}\n\t} else {\n\t\tmsg += payload;\n\t}\n\tmsg += '\\n';\n\treturn msg.toString();\n}\n}\n\n\nvar MySHelperObj = new MySHelper();\n\ncontext.global.MYS = MySHelperObj;\n\nreturn msg;","outputs":1,"noerr":0,"x":364.25,"y":65.99999809265137,"wires":[[]]},{"id":"df1e322.f20e1d","type":"function","z":"9592163f.6a6de8","name":"Set Controller 1","func":"msg.controller = 1\n\nreturn msg;","outputs":1,"noerr":0,"x":641.0000076293945,"y":147.49999809265137,"wires":[["ebcef3df.14311"]]},{"id":"266b87b3.d99478","type":"switch","z":"9592163f.6a6de8","name":"route to controller n","property":"controller","rules":[{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"false","outputs":4,"x":133,"y":214.25,"wires":[["3e866f6d.c1799"],["c7d0d88b.382f28"],[],[]]},{"id":"c7d0d88b.382f28","type":"tcp request","z":"9592163f.6a6de8","server":"192.168.92.14","port":"5003","out":"sit","splitc":"0","name":"MySWifi ESP8266 GW AES 14","x":410.5,"y":207.24999618530273,"wires":[["c5f14d8f.3a0eb"]]},{"id":"c5f14d8f.3a0eb","type":"function","z":"9592163f.6a6de8","name":"Set Controller 2","func":"msg.controller = 2\n\nreturn msg;","outputs":1,"noerr":0,"x":653.5,"y":205.7500114440918,"wires":[["ebcef3df.14311"]]},{"id":"56b9f6ab.a94608","type":"file in","z":"9592163f.6a6de8","name":"read store for next ids","filename":"mysids.dump","format":"utf8","x":385,"y":103.99999618530273,"wires":[["57db23d6.a824dc"]]},{"id":"e000bd09.1fff4","type":"debug","z":"9592163f.6a6de8","name":"Debug","active":false,"console":"false","complete":"true","x":732,"y":361,"wires":[]},{"id":"57db23d6.a824dc","type":"function","z":"9592163f.6a6de8","name":"store to context.global.mysnextid","func":"if (msg.payload === undefined) {\n var mysnextid = {};\n\n obj = mysnextid; \n}\nelse \n{\ntry{\n obj = JSON.parse(msg.payload);\n }\n catch(e){\n \n var mysnextid = {};\n\n obj = mysnextid;\n \n }\n} \n\ncontext.global.mysnextid = obj;\n\nmsg.payload = context.global.mysnextid;\n\nreturn msg;","outputs":1,"noerr":0,"x":630,"y":102.99999618530273,"wires":[[]]},{"id":"dfba7d69.20458","type":"file","z":"9592163f.6a6de8","name":"dump mysids","filename":"mysids.dump","appendNewline":true,"createDir":false,"overwriteFile":"true","x":1473,"y":381.99999618530273,"wires":[]},{"id":"e0e76d62.1f189","type":"function","z":"9592163f.6a6de8","name":"handle nextids","func":"// increase nextid, if nodeid >= nextid \n// node.log(\"Handling next ids\");\n// node.log(\"nodeId: \" + msg.nodeId);\n\nbChanged = false;\n\nif (msg.nodeId === 0) return;\n\nif (msg.nodeId < 255)\n{\n // node.log(\"Test if next node-id must be set\");\n if (context.global.mysnextid[msg.controller] === undefined) {\n node.log(\"node-id not initialized yet\");\n context.global.mysnextid[msg.controller] = msg.nodeId+1;\n if (context.global.mysnextid[msg.controller] < context.global.MYS.MIN_NODEID)\n context.global.mysnextid[msg.controller] = context.global.MYS.MIN_NODEID;\n bChanged = true;\n }\n \n // node.log(\"Nexid stored \" + parseInt(context.global.mysnextid[msg.controller]));\n \n if (msg.nodeId >= parseInt(context.global.mysnextid[msg.controller])) {\n node.log(\"node-id >= next -> increase\");\n // convert to int\n context.global.mysnextid[msg.controller] = parseInt(context.global.mysnextid[msg.controller]);\n context.global.mysnextid[msg.controller] = msg.nodeId+1; \n if (context.global.mysnextid[msg.controller] < context.global.MYS.MIN_NODEID)\n context.global.mysnextid[msg.controller] = context.global.MYS.MIN_NODEID;\n bChanged = true;\n }\n\n if (bChanged) {\n node.log(\"next id must be stored\");\n msg.payload = JSON.stringify(context.global.mysnextid); \n return msg;\n }\n}\n\n\n","outputs":1,"noerr":0,"x":1262,"y":374.99999618530273,"wires":[["dfba7d69.20458","5c074c19.a3f8b4"]]},{"id":"8da09002.725f7","type":"function","z":"9592163f.6a6de8","name":"MQTT to MYS convert","func":"// topic = MYS-NODERED/set/controller/node-id/sensor-id/ack/sub-type\n// payload = payload :)\n\n var tokens = msg.topic.split(\"/\")\n \n msg.rawData = tokens;\n msg.tokens = tokens.length;\n if(tokens.length == 7)\n {\n if (tokens[0] != context.global.MYS.TOPIC_PREFIX) // not for us\n return;\n if (tokens[1] != 'set') // not for us\n return;\n \n msg.controller = parseInt(tokens[2]);\n msg.messageType = context.global.MYS.T_SET;\n msg.nodeId = parseInt(tokens[3]);\n msg.childSensorId = parseInt(tokens[4]);\n msg.ack = parseInt(tokens[5]);\n msg.subType = context.global.MYS.VNum(tokens[6]);\n \n msg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, msg.messageType, msg.ack, msg.subType, msg.payload);\n \n return msg; \n }\n","outputs":1,"noerr":0,"x":490,"y":361,"wires":[["e000bd09.1fff4","266b87b3.d99478"]]},{"id":"3e866f6d.c1799","type":"tcp request","z":"9592163f.6a6de8","server":"192.168.92.13","port":"5003","out":"sit","splitc":"0","name":"MySWifi ESP8266 GW AES 13","x":407,"y":145.99999618530273,"wires":[["df1e322.f20e1d"]]},{"id":"5c074c19.a3f8b4","type":"debug","z":"9592163f.6a6de8","name":"","active":true,"console":"false","complete":"false","x":1454,"y":543.9999961853027,"wires":[]},{"id":"c75fd7f4.38a028","type":"mqtt in","z":"9592163f.6a6de8","name":"Read MQTT Stream: change Topic to your needs","topic":"MYS-NODERED/set/#","broker":"ba386057.845d3","x":183.5,"y":362,"wires":[["8da09002.725f7"]]}]```@FotoFieber keep going. Each time you post a new release I get it, even if i'm not using it :).
But it really gives ideas on what we can do with node-red.
Anyway thanks for your work and haring -
Stability is not sufficient. The connection gets lost from time to time.
Added a watchdog to add another connection, if no messages arrives.
Seems, that this is only interesting for me. If I get no feedback I will stop spaming this thread. :smiley:
[{"id":"ba386057.845d3","type":"mqtt-broker","broker":"192.168.92.4","port":"1883","clientid":"NodeRed"},{"id":"e6ce260d.1931d8","type":"switch","z":"9592163f.6a6de8","name":"switch message type","property":"messageType","rules":[{"t":"eq","v":"0"},{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"true","outputs":5,"x":1259.166648864746,"y":182.50001335144043,"wires":[["8c663d73.7399c"],["4a1e5f84.b5e1a"],["7753f9a2.88ac08"],["1e4aa61b.e1b55a"],["60a0dde4.9f5f24"]]},{"id":"8c663d73.7399c","type":"function","z":"9592163f.6a6de8","name":"presentation","func":"msg.subTypeString = context.global.MYS.SString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1488.916648864746,"y":45.24998474121094,"wires":[["df9e131d.2061f","4d15a037.b2ea6"]]},{"id":"7753f9a2.88ac08","type":"function","z":"9592163f.6a6de8","name":"req","func":"msg.topic = \"req\";\nreturn msg;","outputs":1,"noerr":0,"x":1484.5000228881836,"y":182.75000190734863,"wires":[["4d15a037.b2ea6"]]},{"id":"1e4aa61b.e1b55a","type":"function","z":"9592163f.6a6de8","name":"internal","func":"msg.subTypeString = context.global.MYS.IString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1488.5000228881836,"y":233.00000190734863,"wires":[["df9e131d.2061f","4d15a037.b2ea6","b5e4f17d.4a1b1"]]},{"id":"60a0dde4.9f5f24","type":"function","z":"9592163f.6a6de8","name":"stream","func":"msg.topic = \"stream\";\nreturn msg;","outputs":1,"x":1496.5000228881836,"y":328.00000190734863,"wires":[[]]},{"id":"4d15a037.b2ea6","type":"debug","z":"9592163f.6a6de8","name":"debug","active":false,"console":"false","complete":"true","x":1845.7500267028809,"y":242.00000286102295,"wires":[]},{"id":"4a1e5f84.b5e1a","type":"function","z":"9592163f.6a6de8","name":"set","func":"msg.subTypeString = context.global.MYS.VString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\n\nreturn msg;","outputs":1,"noerr":0,"x":1492.166648864746,"y":107.5,"wires":[["4d15a037.b2ea6","df9e131d.2061f"]]},{"id":"fc54bb91.03ab48","type":"debug","z":"9592163f.6a6de8","name":"","active":false,"console":"false","complete":"true","x":1218.9166259765625,"y":41.66668510437012,"wires":[]},{"id":"6aa2d9f6.955d28","type":"function","z":"9592163f.6a6de8","name":"Split GW Message","func":"\n var tokens = msg.payload.split(\";\")\n \n msg.rawData = tokens;\n if(tokens.length >= 6)\n {\n msg.nodeId = parseInt(tokens[0]);\n msg.childSensorId = parseInt(tokens[1]);\n msg.messageType = parseInt(tokens[2]);\n msg.ack = parseInt(tokens[3]);\n msg.subType = parseInt(tokens[4]);\n msg.payload = tokens[5];\n for (j=6; j<tokens.length; j++) \n msg.payload = msg.payload + ';' + tokens[j];\n }\n\nreturn msg;","outputs":1,"noerr":0,"x":1023.6666488647461,"y":180.66664123535156,"wires":[["e6ce260d.1931d8","fc54bb91.03ab48","e0e76d62.1f189"]]},{"id":"df9e131d.2061f","type":"mqtt out","z":"9592163f.6a6de8","name":"Publish to MQTT","topic":"","qos":"","retain":"","broker":"ba386057.845d3","x":1858.9166526794434,"y":181.16665649414062,"wires":[]},{"id":"b5e4f17d.4a1b1","type":"function","z":"9592163f.6a6de8","name":"hanlde internal messages","func":"//msg.subTypeString = \"\";\n//msg.topic = \"internal respones\";\n\nif (msg.subTypeString == 'I_TIME')\n{\n var payload = parseInt(new Date().getTime()/1000);\n\tvar command = context.global.MYS.T_INTERNAL; \n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_TIME; // I_TIME\n\tmsg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg;\n \n}\nelse if (msg.subTypeString == 'I_ID_REQUEST')\n{\n msg.topic = \"I_ID_RESPONSE\";\n msg.subTypeString = \"I_ID_RESPONSE\";\n // 255;255;3;0;4;8 for ID 8\n var command = context.global.MYS.T_INTERNAL;\n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_ID_RESPONSE; // I_ID_RESPONSE\n\n\tif (context.global.mysnextid[msg.controller] === undefined) {\n\t payload = context.global.MYS.MIN_NODEID;\n\t} \n\telse\n\t{\n\t payload = context.global.mysnextid[msg.controller];\n\t}\n\t\n msg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg; \n} \nelse if (msg.subTypeString == 'I_CONFIG')\n{\n var payload = 'M';\n\tvar command = context.global.MYS.T_INTERNAL; \n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_CONFIG; // I_TIME\n\tmsg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg;\n}\nelse if (msg.subTypeString == 'I_INCLUSION_MODE')\n{\n // not yet implemented\n}\n\nreturn;\n\n\n","outputs":1,"noerr":0,"x":1694.916648864746,"y":543.4166889190674,"wires":[["4d15a037.b2ea6","266b87b3.d99478"]]},{"id":"e6d67f33.19298","type":"inject","z":"9592163f.6a6de8","name":"Startup","topic":"","payload":"","payloadType":"none","repeat":"","crontab":"","once":true,"x":145.25,"y":81.41665363311768,"wires":[["64617800.9b9e88","56b9f6ab.a94608","3e866f6d.c1799"]]},{"id":"ebcef3df.14311","type":"function","z":"9592163f.6a6de8","name":"ToString","func":"msg.payload = msg.payload.toString().replace(/[\\n\\r]/g, '');\n\nreturn msg;","outputs":1,"noerr":0,"x":829.1666946411133,"y":181.91668796539307,"wires":[["6aa2d9f6.955d28"]]},{"id":"31047fa6.cefb8","type":"catch","z":"9592163f.6a6de8","name":"","x":58,"y":449,"wires":[["3622f9b9.c9dd06"]]},{"id":"3622f9b9.c9dd06","type":"debug","z":"9592163f.6a6de8","name":"","active":false,"console":"false","complete":"true","x":224,"y":450,"wires":[]},{"id":"64617800.9b9e88","type":"function","z":"9592163f.6a6de8","name":"MYS Initialize","func":"function MySHelper() { \n\nMySHelper.prototype.TOPIC_PREFIX = \"MYS-NODERED\";\n\nMySHelper.prototype.MIN_NODEID = 10;\n\n\n// don't touch below :)\n \nMySHelper.prototype.T_PRESENTATION = 0;\nMySHelper.prototype.T_SET = 1;\nMySHelper.prototype.T_REQ = 2;\nMySHelper.prototype.T_INTERNAL = 3;\nMySHelper.prototype.T_STREAM = 4;\n\nMySHelper.prototype.I_BATTERY_LEVEL = 0;\nMySHelper.prototype.I_TIME = 1;\nMySHelper.prototype.I_VERSION = 2;\nMySHelper.prototype.I_ID_REQUEST = 3;\nMySHelper.prototype.I_ID_RESPONSE = 4;\nMySHelper.prototype.I_INCLUSION_MODE = 5;\nMySHelper.prototype.I_CONFIG = 6;\nMySHelper.prototype.I_PING = 7;\nMySHelper.prototype.I_PING_ACK = 8;\nMySHelper.prototype.I_LOG_MESSAGE = 9;\nMySHelper.prototype.I_CHILDREN = 10;\nMySHelper.prototype.I_SKETCH_NAME = 11;\nMySHelper.prototype.I_SKETCH_VERSION = 12;\nMySHelper.prototype.I_REBOOT = 13;\nMySHelper.prototype.I_GATEWAY_READY = 14;\nMySHelper.prototype.I_REQUEST_SIGNING = 15;\nMySHelper.prototype.I_GET_NONCE = 16;\nMySHelper.prototype.I_GET_NONCE_RESPONSE = 17;\nMySHelper.prototype.I_HEARTBEAT = 18;\nMySHelper.prototype.I_PRESENTATION = 19;\n \nvar itype = {\nI_BATTERY_LEVEL: MySHelper.prototype.I_BATTERY_LEVEL,\nI_TIME: MySHelper.prototype.I_TIME,\nI_VERSION: MySHelper.prototype.I_VERSION,\nI_ID_REQUEST: MySHelper.prototype.I_ID_REQUEST,\nI_ID_RESPONSE: MySHelper.prototype.I_ID_RESPONSE,\nI_INCLUSION_MODE: MySHelper.prototype.I_INCLUSION_MODE,\nI_CONFIG: MySHelper.prototype.I_CONFIG,\nI_PING: MySHelper.prototype.I_PING,\nI_PING_ACK: MySHelper.prototype.I_PING_ACK,\nI_LOG_MESSAGE: MySHelper.prototype.I_LOG_MESSAGE,\nI_CHILDREN: MySHelper.prototype.I_CHILDREN,\nI_SKETCH_NAME: MySHelper.prototype.I_SKETCH_NAME,\nI_SKETCH_VERSION: MySHelper.prototype.I_SKETCH_VERSION,\nI_REBOOT: MySHelper.prototype.I_REBOOT,\nI_GATEWAY_READY: MySHelper.prototype.I_GATEWAY_READY,\nI_REQUEST_SIGNING: MySHelper.prototype.I_REQUEST_SIGNING,\nI_GET_NONCE: MySHelper.prototype.I_GET_NONCE,\nI_GET_NONCE_RESPONSE: MySHelper.prototype.I_GET_NONCE_RESPONSE,\nI_HEARTBEAT: MySHelper.prototype.I_HEARTBEAT,\nI_PRESENTATION: MySHelper.prototype.I_PRESENTATION\n};\n\nMySHelper.prototype.IString = function(I_SUBTYPE) {\n for (var prop in itype ) \n if( itype[ prop ] === parseInt(I_SUBTYPE) )\n return prop;\n};\n\nMySHelper.prototype.V_TEMP = 0;\nMySHelper.prototype.V_HUM = 1;\nMySHelper.prototype.V_LIGHT = 2;\nMySHelper.prototype.V_STATUS = 2;\nMySHelper.prototype.V_DIMMER = 3;\nMySHelper.prototype.V_PRESSURE = 4;\nMySHelper.prototype.V_FORECAST = 5;\nMySHelper.prototype.V_RAIN = 6;\nMySHelper.prototype.V_RAINRATE = 7;\nMySHelper.prototype.V_WIND = 8;\nMySHelper.prototype.V_GUST = 9;\nMySHelper.prototype.V_DIRECTION = 10;\nMySHelper.prototype.V_UV = 11;\nMySHelper.prototype.V_WEIGHT = 12;\nMySHelper.prototype.V_DISTANCE = 13;\nMySHelper.prototype.V_IMPEDANCE = 14;\nMySHelper.prototype.V_ARMED = 15;\nMySHelper.prototype.V_TRIPPED = 16;\nMySHelper.prototype.V_WATT = 17;\nMySHelper.prototype.V_KWH = 18;\nMySHelper.prototype.V_SCENE_ON = 19;\nMySHelper.prototype.V_SCENE_OFF = 20;\nMySHelper.prototype.V_HEATER = 21;\nMySHelper.prototype.V_HEATER_SW = 22;\nMySHelper.prototype.V_LIGHT_LEVEL = 23;\nMySHelper.prototype.V_VAR1 = 24;\nMySHelper.prototype.V_VAR2 = 25;\nMySHelper.prototype.V_VAR3 = 26;\nMySHelper.prototype.V_VAR4 = 27;\nMySHelper.prototype.V_VAR5 = 28;\nMySHelper.prototype.V_UP = 29;\nMySHelper.prototype.V_DOWN = 30;\nMySHelper.prototype.V_STOP = 31;\nMySHelper.prototype.V_IR_SEND = 32;\nMySHelper.prototype.V_IR_RECEIVE = 33;\nMySHelper.prototype.V_FLOW = 34;\nMySHelper.prototype.V_VOLUME = 35;\nMySHelper.prototype.V_LOCK_STATUS = 36;\nMySHelper.prototype.V_LEVEL = 37; \nMySHelper.prototype.V_VOLTAGE = 38; \nMySHelper.prototype.V_CURRENT = 39; \nMySHelper.prototype.V_RGB = 40; \nMySHelper.prototype.V_RGBW = 41;\nMySHelper.prototype.V_ID = 42;\nMySHelper.prototype.V_UNIT_PREFIX = 43;\nMySHelper.prototype.V_HVAC_SETPOINT_COOL = 44;\nMySHelper.prototype.V_HVAC_SETPOINT_HEAT = 45;\nMySHelper.prototype.V_HVAC_FLOW_MODE = 46;\nMySHelper.prototype.V_TEXT = 47;\n\nvar vtype = {\nV_TEMP: MySHelper.prototype.V_TEMP,\nV_HUM: MySHelper.prototype.V_HUM,\nV_STATUS: MySHelper.prototype.V_STATUS,\nV_LIGHT: MySHelper.prototype.V_LIGHT,\nV_DIMMER: MySHelper.prototype.V_DIMMER,\nV_PRESSURE: MySHelper.prototype.V_PRESSURE,\nV_FORECAST: MySHelper.prototype.V_FORECAST,\nV_RAIN: MySHelper.prototype.V_RAIN,\nV_RAINRATE: MySHelper.prototype.V_RAINRATE,\nV_WIND: MySHelper.prototype.V_WIND,\nV_GUST: MySHelper.prototype.V_GUST,\nV_DIRECTION: MySHelper.prototype.V_DIRECTION,\nV_UV: MySHelper.prototype.V_UV,\nV_WEIGHT: MySHelper.prototype.V_WEIGHT,\nV_DISTANCE: MySHelper.prototype.V_DISTANCE,\nV_IMPEDANCE: MySHelper.prototype.V_IMPEDANCE,\nV_ARMED: MySHelper.prototype.V_ARMED,\nV_TRIPPED: MySHelper.prototype.V_TRIPPED,\nV_WATT: MySHelper.prototype.V_WATT,\nV_KWH: MySHelper.prototype.V_KWH,\nV_SCENE_ON: MySHelper.prototype.V_SCENE_ON,\nV_SCENE_OFF: MySHelper.prototype.V_SCENE_OFF,\nV_HEATER: MySHelper.prototype.V_HEATER,\nV_HEATER_SW: MySHelper.prototype.V_HEATER_SW,\nV_LIGHT_LEVEL: MySHelper.prototype.V_LIGHT_LEVEL,\nV_VAR1: MySHelper.prototype.V_VAR1,\nV_VAR2: MySHelper.prototype.V_VAR2,\nV_VAR3: MySHelper.prototype.V_VAR3,\nV_VAR4: MySHelper.prototype.V_VAR4,\nV_VAR5: MySHelper.prototype.V_VAR5,\nV_UP: MySHelper.prototype.V_UP,\nV_DOWN: MySHelper.prototype.V_DOWN,\nV_STOP: MySHelper.prototype.V_STOP,\nV_IR_SEND: MySHelper.prototype.V_IR_SEND,\nV_IR_RECEIVE: MySHelper.prototype.V_IR_RECEIVE,\nV_FLOW: MySHelper.prototype.V_FLOW,\nV_VOLUME: MySHelper.prototype.V_VOLUME,\nV_LOCK_STATUS: MySHelper.prototype.V_LOCK_STATUS,\nV_LEVEL: MySHelper.prototype.V_LEVEL,\nV_VOLTAGE: MySHelper.prototype.V_VOLTAGE, \nV_CURRENT: MySHelper.prototype.V_CURRENT,\nV_RGB: MySHelper.prototype.V_RGB,\nV_RGBW: MySHelper.prototype.V_RGBW,\nV_ID: MySHelper.prototype.V_ID,\nV_UNIT_PREFIX: MySHelper.prototype.V_UNIT_PREFIX,\nV_HVAC_SETPOINT_COOL:MySHelper.prototype.V_HVAC_SETPOINT_COOL,\nV_HVAC_SETPOINT_HEAT:MySHelper.prototype.V_HVAC_SETPOINT_HEAT,\nV_HVAC_FLOW_MODE: MySHelper.prototype.V_HVAC_FLOW_MODE,\nV_TEXT: MySHelper.prototype.V_TEXT\n};\n\n\n\nMySHelper.prototype.VString = function(V_SUBTYPE) {\n for (var prop in vtype ) \n if( vtype[ prop ] === parseInt(V_SUBTYPE) )\n return prop;\n};\n \nMySHelper.prototype.VNum = function(V_SUBTYPE) {\n sRet = vtype [V_SUBTYPE];\n if (sRet === undefined)\n sRet = V_SUBTYPE;\n return sRet;\n}\n\nMySHelper.prototype.S_DOOR = 0; // Door sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_MOTION = 1; // Motion sensor; V_TRIPPED; V_ARMED \nMySHelper.prototype.S_SMOKE = 2; // Smoke sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_LIGHT = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nMySHelper.prototype.S_BINARY = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nMySHelper.prototype.S_DIMMER = 4; // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nMySHelper.prototype.S_COVER = 5; // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nMySHelper.prototype.S_TEMP = 6; // Temperature sensor; V_TEMP\nMySHelper.prototype.S_HUM = 7; // Humidity sensor; V_HUM\nMySHelper.prototype.S_BARO = 8; // Barometer sensor; V_PRESSURE; V_FORECAST\nMySHelper.prototype.S_WIND = 9; // Wind sensor; V_WIND; V_GUST\nMySHelper.prototype.S_RAIN = 10; // Rain sensor; V_RAIN; V_RAINRATE\nMySHelper.prototype.S_UV = 11; // Uv sensor; V_UV\nMySHelper.prototype.S_WEIGHT = 12; // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nMySHelper.prototype.S_POWER = 13; // Power meter; V_WATT; V_KWH\nMySHelper.prototype.S_HEATER = 14; // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nMySHelper.prototype.S_DISTANCE = 15; // Distance sensor; V_DISTANCE\nMySHelper.prototype.S_LIGHT_LEVEL = 16; // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nMySHelper.prototype.S_ARDUINO_NODE = 17 ; // Used (internally) for presenting a non-repeating Arduino node\nMySHelper.prototype.S_ARDUINO_REPEATER_NODE = 18; // Used (internally) for presenting a repeating Arduino node \nMySHelper.prototype.S_LOCK = 19; // Lock device; V_LOCK_STATUS\nMySHelper.prototype.S_IR = 20; // Ir device; V_IR_SEND; V_IR_RECEIVE\nMySHelper.prototype.S_WATER = 21; // Water meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_AIR_QUALITY = 22; // Air quality sensor; V_LEVEL\nMySHelper.prototype.S_CUSTOM = 23; // Custom sensor \nMySHelper.prototype.S_DUST = 24; // Dust sensor; V_LEVEL\nMySHelper.prototype.S_SCENE_CONTROLLER = 25; // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nMySHelper.prototype.S_RGB_LIGHT = 26; // RGB light. Send color component data using V_RGB. Also supports V_WATT \nMySHelper.prototype.S_RGBW_LIGHT = 27; // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nMySHelper.prototype.S_COLOR_SENSOR = 28; // Color sensor; send color information using V_RGB\nMySHelper.prototype.S_HVAC = 28; // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nMySHelper.prototype.S_MULTIMETER = 29; // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nMySHelper.prototype.S_SPRINKLER = 30; // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nMySHelper.prototype.S_WATER_LEAK = 31; // Water leak sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_SOUND = 32; // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nMySHelper.prototype.S_VIBRATION = 33; // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nMySHelper.prototype.S_MOISTURE = 34; // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nMySHelper.prototype.S_INFO = 35; // LCD text device / Simple information device on controller; V_TEXT\nMySHelper.prototype.S_GAS = 36; // Gas meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_GPS = 37; // GPS Sensor; V_POSITION\n \nvar stype = {\nS_DOOR: MySHelper.prototype.S_DOOR, // Door sensor; V_TRIPPED; V_ARMED\nS_MOTION: MySHelper.prototype.S_MOTION, // Motion sensor; V_TRIPPED; V_ARMED \nS_SMOKE: MySHelper.prototype.S_SMOKE, // Smoke sensor; V_TRIPPED; V_ARMED\nS_LIGHT: MySHelper.prototype.S_LIGHT, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nS_BINARY: MySHelper.prototype.S_BINARY, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nS_DIMMER: MySHelper.prototype.S_DIMMER, // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nS_COVER: MySHelper.prototype.S_COVER, // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nS_TEMP: MySHelper.prototype.S_TEMP, // Temperature sensor; V_TEMP\nS_HUM: MySHelper.prototype.S_HUM, // Humidity sensor; V_HUM\nS_BARO: MySHelper.prototype.S_BARO, // Barometer sensor; V_PRESSURE; V_FORECAST\nS_WIND: MySHelper.prototype.S_WIND, // Wind sensor; V_WIND; V_GUST\nS_RAIN: MySHelper.prototype.S_RAIN, // Rain sensor; V_RAIN; V_RAINRATE\nS_UV: MySHelper.prototype.S_UV, // Uv sensor; V_UV\nS_WEIGHT: MySHelper.prototype.S_WEIGHT, // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nS_POWER: MySHelper.prototype.S_POWER, // Power meter; V_WATT; V_KWH\nS_HEATER: MySHelper.prototype.S_HEATER, // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nS_DISTANCE: MySHelper.prototype.S_DISTANCE, // Distance sensor; V_DISTANCE\nS_LIGHT_LEVEL: MySHelper.prototype.S_LIGHT_LEVEL, // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nS_ARDUINO_NODE: MySHelper.prototype.S_ARDUINO_NODE, // Used (internally) for presenting a non-repeating Arduino node\nS_ARDUINO_REPEATER_NODE:MySHelper.prototype.S_ARDUINO_REPEATER_NODE, // Used (internally) for presenting a repeating Arduino node \nS_LOCK: MySHelper.prototype.S_LOCK, // Lock device; V_LOCK_STATUS\nS_IR: MySHelper.prototype.S_IR, // Ir device; V_IR_SEND; V_IR_RECEIVE\nS_WATER: MySHelper.prototype.S_WATER, // Water meter; V_FLOW; V_VOLUME\nS_AIR_QUALITY: MySHelper.prototype.S_AIR_QUALITY, // Air quality sensor; V_LEVEL\nS_CUSTOM: MySHelper.prototype.S_CUSTOM, // Custom sensor \nS_DUST: MySHelper.prototype.S_DUST, // Dust sensor; V_LEVEL\nS_SCENE_CONTROLLER: MySHelper.prototype.S_SCENE_CONTROLLER, // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nS_RGB_LIGHT: MySHelper.prototype.S_RGB_LIGHT, // RGB light. Send color component data using V_RGB. Also supports V_WATT \nS_RGBW_LIGHT: MySHelper.prototype.S_RGBW_LIGHT, // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nS_COLOR_SENSOR: MySHelper.prototype.S_COLOR_SENSOR, // Color sensor; send color information using V_RGB\nS_HVAC: MySHelper.prototype.S_HVAC, // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nS_MULTIMETER: MySHelper.prototype.S_MULTIMETER, // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nS_SPRINKLER: MySHelper.prototype.S_SPRINKLER, // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nS_WATER_LEAK: MySHelper.prototype.S_WATER_LEAK, // Water leak sensor; V_TRIPPED; V_ARMED\nS_SOUND: MySHelper.prototype.S_SOUND, // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nS_VIBRATION: MySHelper.prototype.S_VIBRATION, // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nS_MOISTURE: MySHelper.prototype.S_MOISTURE, // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nS_INFO: MySHelper.prototype.S_INFO, // LCD text device / Simple information device on controller; V_TEXT\nS_GAS: MySHelper.prototype.S_GAS, // Gas meter; V_FLOW; V_VOLUME\nS_GPS: MySHelper.prototype.S_GPS // GPS Sensor; V_POSITION\n};\n\nMySHelper.prototype.SString = function(S_SUBTYPE) {\n for (var prop in stype ) \n if( stype[ prop ] === parseInt(S_SUBTYPE) )\n return prop;\n}; \n \n MySHelper.prototype.encode = function(destination, sensor, command, acknowledge, type, payload) {\n\tvar msg = destination.toString(10) + \";\" + sensor.toString(10) + \";\" + command.toString(10) + \";\" + acknowledge.toString(10) + \";\" + type.toString(10) + \";\";\n\tif (command == 4) {\n\t\tfor (var i = 0; i < payload.length; i++) {\n\t\t\tif (payload[i] < 16)\n\t\t\t\tmsg += \"0\";\n\t\t\tmsg += payload[i].toString(16);\n\t\t}\n\t} else {\n\t\tmsg += payload;\n\t}\n\tmsg += '\\n';\n\treturn msg.toString();\n}\n}\n\n\nvar MySHelperObj = new MySHelper();\n\ncontext.global.MYS = MySHelperObj;\n\nreturn msg;","outputs":1,"noerr":0,"x":383.25,"y":20,"wires":[[]]},{"id":"df1e322.f20e1d","type":"function","z":"9592163f.6a6de8","name":"Set Controller 1","func":"msg.controller = 1\n\nreturn msg;","outputs":1,"noerr":0,"x":641.0000076293945,"y":147.49999809265137,"wires":[["ebcef3df.14311"]]},{"id":"266b87b3.d99478","type":"switch","z":"9592163f.6a6de8","name":"route to controller n","property":"controller","rules":[{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"false","outputs":4,"x":133,"y":214.25,"wires":[["3e866f6d.c1799"],["c7d0d88b.382f28"],[],[]]},{"id":"c7d0d88b.382f28","type":"tcp request","z":"9592163f.6a6de8","server":"192.168.92.14","port":"5003","out":"sit","splitc":"0","name":"MySWifi ESP8266 GW AES 14","x":410.5,"y":207.24999618530273,"wires":[["c5f14d8f.3a0eb"]]},{"id":"c5f14d8f.3a0eb","type":"function","z":"9592163f.6a6de8","name":"Set Controller 2","func":"msg.controller = 2\n\nreturn msg;","outputs":1,"noerr":0,"x":653.5,"y":205.7500114440918,"wires":[["ebcef3df.14311"]]},{"id":"56b9f6ab.a94608","type":"file in","z":"9592163f.6a6de8","name":"read store for next ids","filename":"mysids.dump","format":"utf8","x":395,"y":65,"wires":[["57db23d6.a824dc"]]},{"id":"e000bd09.1fff4","type":"debug","z":"9592163f.6a6de8","name":"Debug","active":false,"console":"false","complete":"true","x":732,"y":361,"wires":[]},{"id":"57db23d6.a824dc","type":"function","z":"9592163f.6a6de8","name":"store to context.global.mysnextid","func":"if (msg.payload === undefined) {\n var mysnextid = {};\n\n obj = mysnextid; \n}\nelse \n{\ntry{\n obj = JSON.parse(msg.payload);\n }\n catch(e){\n \n var mysnextid = {};\n\n obj = mysnextid;\n \n }\n} \n\ncontext.global.mysnextid = obj;\n\nmsg.payload = context.global.mysnextid;\n\nreturn msg;","outputs":1,"noerr":0,"x":658,"y":53,"wires":[[]]},{"id":"dfba7d69.20458","type":"file","z":"9592163f.6a6de8","name":"dump mysids","filename":"mysids.dump","appendNewline":true,"createDir":false,"overwriteFile":"true","x":1473,"y":381.99999618530273,"wires":[]},{"id":"e0e76d62.1f189","type":"function","z":"9592163f.6a6de8","name":"handle nextids","func":"// increase nextid, if nodeid >= nextid \n// node.log(\"Handling next ids\");\n// node.log(\"nodeId: \" + msg.nodeId);\n\nbChanged = false;\n\nif (msg.nodeId === 0) return;\n\nif (msg.nodeId < 255)\n{\n // node.log(\"Test if next node-id must be set\");\n if (context.global.mysnextid[msg.controller] === undefined) {\n node.log(\"node-id not initialized yet\");\n context.global.mysnextid[msg.controller] = msg.nodeId+1;\n if (context.global.mysnextid[msg.controller] < context.global.MYS.MIN_NODEID)\n context.global.mysnextid[msg.controller] = context.global.MYS.MIN_NODEID;\n bChanged = true;\n }\n \n // node.log(\"Nexid stored \" + parseInt(context.global.mysnextid[msg.controller]));\n \n if (msg.nodeId >= parseInt(context.global.mysnextid[msg.controller])) {\n node.log(\"node-id >= next -> increase\");\n // convert to int\n context.global.mysnextid[msg.controller] = parseInt(context.global.mysnextid[msg.controller]);\n context.global.mysnextid[msg.controller] = msg.nodeId+1; \n if (context.global.mysnextid[msg.controller] < context.global.MYS.MIN_NODEID)\n context.global.mysnextid[msg.controller] = context.global.MYS.MIN_NODEID;\n bChanged = true;\n }\n\n if (bChanged) {\n node.log(\"next id must be stored\");\n msg.payload = JSON.stringify(context.global.mysnextid); \n return msg;\n }\n}\n\n\n","outputs":1,"noerr":0,"x":1262,"y":374.99999618530273,"wires":[["dfba7d69.20458","5c074c19.a3f8b4"]]},{"id":"8da09002.725f7","type":"function","z":"9592163f.6a6de8","name":"MQTT to MYS convert","func":"// topic = MYS-NODERED/set/controller/node-id/sensor-id/ack/sub-type\n// payload = payload :)\n\n var tokens = msg.topic.split(\"/\");\n \n msg.rawData = tokens;\n msg.tokens = tokens.length;\n if(tokens.length == 7)\n {\n if (tokens[0] != context.global.MYS.TOPIC_PREFIX) // not for us\n return;\n if (tokens[1] != 'set') // not for us\n return;\n \n msg.controller = parseInt(tokens[2]);\n msg.messageType = context.global.MYS.T_SET;\n msg.nodeId = parseInt(tokens[3]);\n msg.childSensorId = parseInt(tokens[4]);\n msg.ack = parseInt(tokens[5]);\n msg.subType = context.global.MYS.VNum(tokens[6]);\n \n msg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, msg.messageType, msg.ack, msg.subType, msg.payload);\n \n return msg; \n }\n","outputs":1,"noerr":0,"x":490,"y":361,"wires":[["e000bd09.1fff4","266b87b3.d99478"]]},{"id":"3e866f6d.c1799","type":"tcp request","z":"9592163f.6a6de8","server":"192.168.92.13","port":"5003","out":"sit","splitc":"0","name":"MySWifi ESP8266 GW AES 13","x":407,"y":145.99999618530273,"wires":[["df1e322.f20e1d","9386fdb0.6c79"]]},{"id":"5c074c19.a3f8b4","type":"debug","z":"9592163f.6a6de8","name":"","active":true,"console":"false","complete":"false","x":1454,"y":543.9999961853027,"wires":[]},{"id":"c75fd7f4.38a028","type":"mqtt in","z":"9592163f.6a6de8","name":"Read MQTT Stream: change Topic to your needs","topic":"MYS-NODERED/set/#","broker":"ba386057.845d3","x":183.5,"y":362,"wires":[["8da09002.725f7"]]},{"id":"9386fdb0.6c79","type":"function","z":"9592163f.6a6de8","name":"Watchdog controller 1","func":"if (isNaN(context.global.controller1count))\n context.global.controller1count=0;\n\n\ncontext.global.controller1count++;\n\n","outputs":1,"noerr":0,"x":630,"y":105,"wires":[[]]},{"id":"d465a67.f2b9a58","type":"inject","z":"9592163f.6a6de8","name":"Check health controller 1 every 5 minutes","topic":"","payload":"","payloadType":"none","repeat":"60","crontab":"","once":false,"x":173,"y":516,"wires":[["aa935a.ff556ca8"]]},{"id":"aa935a.ff556ca8","type":"function","z":"9592163f.6a6de8","name":"check health controlller 1","func":"if (isNaN(context.global.controller1count))\n context.global.controller1count=0;\n \nif (context.global.controller1count === 0) {\n // make a new connection to the controller\n msg.payload = \"\";\n node.log(\"no message recieved on mys controller 1, try to connect\");\n \n return msg;\n}\nelse\n{\n // reset counter\n context.global.controller1count=0;\n}\n","outputs":1,"noerr":0,"x":470,"y":510,"wires":[["c8b342e9.374cc","3e866f6d.c1799"]]},{"id":"c8b342e9.374cc","type":"debug","z":"9592163f.6a6de8","name":"","active":true,"console":"false","complete":"false","x":682,"y":511,"wires":[]}]```@FotoFieber Please keep going. I always load the scripts to node-red to learn. Thanks
-
Stability is not sufficient. The connection gets lost from time to time.
Added a watchdog to add another connection, if no messages arrives.
Seems, that this is only interesting for me. If I get no feedback I will stop spaming this thread. :smiley:
[{"id":"ba386057.845d3","type":"mqtt-broker","broker":"192.168.92.4","port":"1883","clientid":"NodeRed"},{"id":"e6ce260d.1931d8","type":"switch","z":"9592163f.6a6de8","name":"switch message type","property":"messageType","rules":[{"t":"eq","v":"0"},{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"true","outputs":5,"x":1259.166648864746,"y":182.50001335144043,"wires":[["8c663d73.7399c"],["4a1e5f84.b5e1a"],["7753f9a2.88ac08"],["1e4aa61b.e1b55a"],["60a0dde4.9f5f24"]]},{"id":"8c663d73.7399c","type":"function","z":"9592163f.6a6de8","name":"presentation","func":"msg.subTypeString = context.global.MYS.SString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1488.916648864746,"y":45.24998474121094,"wires":[["df9e131d.2061f","4d15a037.b2ea6"]]},{"id":"7753f9a2.88ac08","type":"function","z":"9592163f.6a6de8","name":"req","func":"msg.topic = \"req\";\nreturn msg;","outputs":1,"noerr":0,"x":1484.5000228881836,"y":182.75000190734863,"wires":[["4d15a037.b2ea6"]]},{"id":"1e4aa61b.e1b55a","type":"function","z":"9592163f.6a6de8","name":"internal","func":"msg.subTypeString = context.global.MYS.IString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\nreturn msg;","outputs":1,"noerr":0,"x":1488.5000228881836,"y":233.00000190734863,"wires":[["df9e131d.2061f","4d15a037.b2ea6","b5e4f17d.4a1b1"]]},{"id":"60a0dde4.9f5f24","type":"function","z":"9592163f.6a6de8","name":"stream","func":"msg.topic = \"stream\";\nreturn msg;","outputs":1,"x":1496.5000228881836,"y":328.00000190734863,"wires":[[]]},{"id":"4d15a037.b2ea6","type":"debug","z":"9592163f.6a6de8","name":"debug","active":false,"console":"false","complete":"true","x":1845.7500267028809,"y":242.00000286102295,"wires":[]},{"id":"4a1e5f84.b5e1a","type":"function","z":"9592163f.6a6de8","name":"set","func":"msg.subTypeString = context.global.MYS.VString(msg.subType);\n\nmsg.topic = context.global.MYS.TOPIC_PREFIX + '/' + msg.controller + \"/\" + msg.nodeId + \"/\" + msg.childSensorId + \"/\" + msg.subTypeString;\n\n\nreturn msg;","outputs":1,"noerr":0,"x":1492.166648864746,"y":107.5,"wires":[["4d15a037.b2ea6","df9e131d.2061f"]]},{"id":"fc54bb91.03ab48","type":"debug","z":"9592163f.6a6de8","name":"","active":false,"console":"false","complete":"true","x":1218.9166259765625,"y":41.66668510437012,"wires":[]},{"id":"6aa2d9f6.955d28","type":"function","z":"9592163f.6a6de8","name":"Split GW Message","func":"\n var tokens = msg.payload.split(\";\")\n \n msg.rawData = tokens;\n if(tokens.length >= 6)\n {\n msg.nodeId = parseInt(tokens[0]);\n msg.childSensorId = parseInt(tokens[1]);\n msg.messageType = parseInt(tokens[2]);\n msg.ack = parseInt(tokens[3]);\n msg.subType = parseInt(tokens[4]);\n msg.payload = tokens[5];\n for (j=6; j<tokens.length; j++) \n msg.payload = msg.payload + ';' + tokens[j];\n }\n\nreturn msg;","outputs":1,"noerr":0,"x":1023.6666488647461,"y":180.66664123535156,"wires":[["e6ce260d.1931d8","fc54bb91.03ab48","e0e76d62.1f189"]]},{"id":"df9e131d.2061f","type":"mqtt out","z":"9592163f.6a6de8","name":"Publish to MQTT","topic":"","qos":"","retain":"","broker":"ba386057.845d3","x":1858.9166526794434,"y":181.16665649414062,"wires":[]},{"id":"b5e4f17d.4a1b1","type":"function","z":"9592163f.6a6de8","name":"hanlde internal messages","func":"//msg.subTypeString = \"\";\n//msg.topic = \"internal respones\";\n\nif (msg.subTypeString == 'I_TIME')\n{\n var payload = parseInt(new Date().getTime()/1000);\n\tvar command = context.global.MYS.T_INTERNAL; \n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_TIME; // I_TIME\n\tmsg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg;\n \n}\nelse if (msg.subTypeString == 'I_ID_REQUEST')\n{\n msg.topic = \"I_ID_RESPONSE\";\n msg.subTypeString = \"I_ID_RESPONSE\";\n // 255;255;3;0;4;8 for ID 8\n var command = context.global.MYS.T_INTERNAL;\n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_ID_RESPONSE; // I_ID_RESPONSE\n\n\tif (context.global.mysnextid[msg.controller] === undefined) {\n\t payload = context.global.MYS.MIN_NODEID;\n\t} \n\telse\n\t{\n\t payload = context.global.mysnextid[msg.controller];\n\t}\n\t\n msg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg; \n} \nelse if (msg.subTypeString == 'I_CONFIG')\n{\n var payload = 'M';\n\tvar command = context.global.MYS.T_INTERNAL; \n\tvar acknowledge = 0; // no ack\n\tvar type = context.global.MYS.I_CONFIG; // I_TIME\n\tmsg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, command, acknowledge, type, payload);\n return msg;\n}\nelse if (msg.subTypeString == 'I_INCLUSION_MODE')\n{\n // not yet implemented\n}\n\nreturn;\n\n\n","outputs":1,"noerr":0,"x":1694.916648864746,"y":543.4166889190674,"wires":[["4d15a037.b2ea6","266b87b3.d99478"]]},{"id":"e6d67f33.19298","type":"inject","z":"9592163f.6a6de8","name":"Startup","topic":"","payload":"","payloadType":"none","repeat":"","crontab":"","once":true,"x":145.25,"y":81.41665363311768,"wires":[["64617800.9b9e88","56b9f6ab.a94608","3e866f6d.c1799"]]},{"id":"ebcef3df.14311","type":"function","z":"9592163f.6a6de8","name":"ToString","func":"msg.payload = msg.payload.toString().replace(/[\\n\\r]/g, '');\n\nreturn msg;","outputs":1,"noerr":0,"x":829.1666946411133,"y":181.91668796539307,"wires":[["6aa2d9f6.955d28"]]},{"id":"31047fa6.cefb8","type":"catch","z":"9592163f.6a6de8","name":"","x":58,"y":449,"wires":[["3622f9b9.c9dd06"]]},{"id":"3622f9b9.c9dd06","type":"debug","z":"9592163f.6a6de8","name":"","active":false,"console":"false","complete":"true","x":224,"y":450,"wires":[]},{"id":"64617800.9b9e88","type":"function","z":"9592163f.6a6de8","name":"MYS Initialize","func":"function MySHelper() { \n\nMySHelper.prototype.TOPIC_PREFIX = \"MYS-NODERED\";\n\nMySHelper.prototype.MIN_NODEID = 10;\n\n\n// don't touch below :)\n \nMySHelper.prototype.T_PRESENTATION = 0;\nMySHelper.prototype.T_SET = 1;\nMySHelper.prototype.T_REQ = 2;\nMySHelper.prototype.T_INTERNAL = 3;\nMySHelper.prototype.T_STREAM = 4;\n\nMySHelper.prototype.I_BATTERY_LEVEL = 0;\nMySHelper.prototype.I_TIME = 1;\nMySHelper.prototype.I_VERSION = 2;\nMySHelper.prototype.I_ID_REQUEST = 3;\nMySHelper.prototype.I_ID_RESPONSE = 4;\nMySHelper.prototype.I_INCLUSION_MODE = 5;\nMySHelper.prototype.I_CONFIG = 6;\nMySHelper.prototype.I_PING = 7;\nMySHelper.prototype.I_PING_ACK = 8;\nMySHelper.prototype.I_LOG_MESSAGE = 9;\nMySHelper.prototype.I_CHILDREN = 10;\nMySHelper.prototype.I_SKETCH_NAME = 11;\nMySHelper.prototype.I_SKETCH_VERSION = 12;\nMySHelper.prototype.I_REBOOT = 13;\nMySHelper.prototype.I_GATEWAY_READY = 14;\nMySHelper.prototype.I_REQUEST_SIGNING = 15;\nMySHelper.prototype.I_GET_NONCE = 16;\nMySHelper.prototype.I_GET_NONCE_RESPONSE = 17;\nMySHelper.prototype.I_HEARTBEAT = 18;\nMySHelper.prototype.I_PRESENTATION = 19;\n \nvar itype = {\nI_BATTERY_LEVEL: MySHelper.prototype.I_BATTERY_LEVEL,\nI_TIME: MySHelper.prototype.I_TIME,\nI_VERSION: MySHelper.prototype.I_VERSION,\nI_ID_REQUEST: MySHelper.prototype.I_ID_REQUEST,\nI_ID_RESPONSE: MySHelper.prototype.I_ID_RESPONSE,\nI_INCLUSION_MODE: MySHelper.prototype.I_INCLUSION_MODE,\nI_CONFIG: MySHelper.prototype.I_CONFIG,\nI_PING: MySHelper.prototype.I_PING,\nI_PING_ACK: MySHelper.prototype.I_PING_ACK,\nI_LOG_MESSAGE: MySHelper.prototype.I_LOG_MESSAGE,\nI_CHILDREN: MySHelper.prototype.I_CHILDREN,\nI_SKETCH_NAME: MySHelper.prototype.I_SKETCH_NAME,\nI_SKETCH_VERSION: MySHelper.prototype.I_SKETCH_VERSION,\nI_REBOOT: MySHelper.prototype.I_REBOOT,\nI_GATEWAY_READY: MySHelper.prototype.I_GATEWAY_READY,\nI_REQUEST_SIGNING: MySHelper.prototype.I_REQUEST_SIGNING,\nI_GET_NONCE: MySHelper.prototype.I_GET_NONCE,\nI_GET_NONCE_RESPONSE: MySHelper.prototype.I_GET_NONCE_RESPONSE,\nI_HEARTBEAT: MySHelper.prototype.I_HEARTBEAT,\nI_PRESENTATION: MySHelper.prototype.I_PRESENTATION\n};\n\nMySHelper.prototype.IString = function(I_SUBTYPE) {\n for (var prop in itype ) \n if( itype[ prop ] === parseInt(I_SUBTYPE) )\n return prop;\n};\n\nMySHelper.prototype.V_TEMP = 0;\nMySHelper.prototype.V_HUM = 1;\nMySHelper.prototype.V_LIGHT = 2;\nMySHelper.prototype.V_STATUS = 2;\nMySHelper.prototype.V_DIMMER = 3;\nMySHelper.prototype.V_PRESSURE = 4;\nMySHelper.prototype.V_FORECAST = 5;\nMySHelper.prototype.V_RAIN = 6;\nMySHelper.prototype.V_RAINRATE = 7;\nMySHelper.prototype.V_WIND = 8;\nMySHelper.prototype.V_GUST = 9;\nMySHelper.prototype.V_DIRECTION = 10;\nMySHelper.prototype.V_UV = 11;\nMySHelper.prototype.V_WEIGHT = 12;\nMySHelper.prototype.V_DISTANCE = 13;\nMySHelper.prototype.V_IMPEDANCE = 14;\nMySHelper.prototype.V_ARMED = 15;\nMySHelper.prototype.V_TRIPPED = 16;\nMySHelper.prototype.V_WATT = 17;\nMySHelper.prototype.V_KWH = 18;\nMySHelper.prototype.V_SCENE_ON = 19;\nMySHelper.prototype.V_SCENE_OFF = 20;\nMySHelper.prototype.V_HEATER = 21;\nMySHelper.prototype.V_HEATER_SW = 22;\nMySHelper.prototype.V_LIGHT_LEVEL = 23;\nMySHelper.prototype.V_VAR1 = 24;\nMySHelper.prototype.V_VAR2 = 25;\nMySHelper.prototype.V_VAR3 = 26;\nMySHelper.prototype.V_VAR4 = 27;\nMySHelper.prototype.V_VAR5 = 28;\nMySHelper.prototype.V_UP = 29;\nMySHelper.prototype.V_DOWN = 30;\nMySHelper.prototype.V_STOP = 31;\nMySHelper.prototype.V_IR_SEND = 32;\nMySHelper.prototype.V_IR_RECEIVE = 33;\nMySHelper.prototype.V_FLOW = 34;\nMySHelper.prototype.V_VOLUME = 35;\nMySHelper.prototype.V_LOCK_STATUS = 36;\nMySHelper.prototype.V_LEVEL = 37; \nMySHelper.prototype.V_VOLTAGE = 38; \nMySHelper.prototype.V_CURRENT = 39; \nMySHelper.prototype.V_RGB = 40; \nMySHelper.prototype.V_RGBW = 41;\nMySHelper.prototype.V_ID = 42;\nMySHelper.prototype.V_UNIT_PREFIX = 43;\nMySHelper.prototype.V_HVAC_SETPOINT_COOL = 44;\nMySHelper.prototype.V_HVAC_SETPOINT_HEAT = 45;\nMySHelper.prototype.V_HVAC_FLOW_MODE = 46;\nMySHelper.prototype.V_TEXT = 47;\n\nvar vtype = {\nV_TEMP: MySHelper.prototype.V_TEMP,\nV_HUM: MySHelper.prototype.V_HUM,\nV_STATUS: MySHelper.prototype.V_STATUS,\nV_LIGHT: MySHelper.prototype.V_LIGHT,\nV_DIMMER: MySHelper.prototype.V_DIMMER,\nV_PRESSURE: MySHelper.prototype.V_PRESSURE,\nV_FORECAST: MySHelper.prototype.V_FORECAST,\nV_RAIN: MySHelper.prototype.V_RAIN,\nV_RAINRATE: MySHelper.prototype.V_RAINRATE,\nV_WIND: MySHelper.prototype.V_WIND,\nV_GUST: MySHelper.prototype.V_GUST,\nV_DIRECTION: MySHelper.prototype.V_DIRECTION,\nV_UV: MySHelper.prototype.V_UV,\nV_WEIGHT: MySHelper.prototype.V_WEIGHT,\nV_DISTANCE: MySHelper.prototype.V_DISTANCE,\nV_IMPEDANCE: MySHelper.prototype.V_IMPEDANCE,\nV_ARMED: MySHelper.prototype.V_ARMED,\nV_TRIPPED: MySHelper.prototype.V_TRIPPED,\nV_WATT: MySHelper.prototype.V_WATT,\nV_KWH: MySHelper.prototype.V_KWH,\nV_SCENE_ON: MySHelper.prototype.V_SCENE_ON,\nV_SCENE_OFF: MySHelper.prototype.V_SCENE_OFF,\nV_HEATER: MySHelper.prototype.V_HEATER,\nV_HEATER_SW: MySHelper.prototype.V_HEATER_SW,\nV_LIGHT_LEVEL: MySHelper.prototype.V_LIGHT_LEVEL,\nV_VAR1: MySHelper.prototype.V_VAR1,\nV_VAR2: MySHelper.prototype.V_VAR2,\nV_VAR3: MySHelper.prototype.V_VAR3,\nV_VAR4: MySHelper.prototype.V_VAR4,\nV_VAR5: MySHelper.prototype.V_VAR5,\nV_UP: MySHelper.prototype.V_UP,\nV_DOWN: MySHelper.prototype.V_DOWN,\nV_STOP: MySHelper.prototype.V_STOP,\nV_IR_SEND: MySHelper.prototype.V_IR_SEND,\nV_IR_RECEIVE: MySHelper.prototype.V_IR_RECEIVE,\nV_FLOW: MySHelper.prototype.V_FLOW,\nV_VOLUME: MySHelper.prototype.V_VOLUME,\nV_LOCK_STATUS: MySHelper.prototype.V_LOCK_STATUS,\nV_LEVEL: MySHelper.prototype.V_LEVEL,\nV_VOLTAGE: MySHelper.prototype.V_VOLTAGE, \nV_CURRENT: MySHelper.prototype.V_CURRENT,\nV_RGB: MySHelper.prototype.V_RGB,\nV_RGBW: MySHelper.prototype.V_RGBW,\nV_ID: MySHelper.prototype.V_ID,\nV_UNIT_PREFIX: MySHelper.prototype.V_UNIT_PREFIX,\nV_HVAC_SETPOINT_COOL:MySHelper.prototype.V_HVAC_SETPOINT_COOL,\nV_HVAC_SETPOINT_HEAT:MySHelper.prototype.V_HVAC_SETPOINT_HEAT,\nV_HVAC_FLOW_MODE: MySHelper.prototype.V_HVAC_FLOW_MODE,\nV_TEXT: MySHelper.prototype.V_TEXT\n};\n\n\n\nMySHelper.prototype.VString = function(V_SUBTYPE) {\n for (var prop in vtype ) \n if( vtype[ prop ] === parseInt(V_SUBTYPE) )\n return prop;\n};\n \nMySHelper.prototype.VNum = function(V_SUBTYPE) {\n sRet = vtype [V_SUBTYPE];\n if (sRet === undefined)\n sRet = V_SUBTYPE;\n return sRet;\n}\n\nMySHelper.prototype.S_DOOR = 0; // Door sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_MOTION = 1; // Motion sensor; V_TRIPPED; V_ARMED \nMySHelper.prototype.S_SMOKE = 2; // Smoke sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_LIGHT = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nMySHelper.prototype.S_BINARY = 3; // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nMySHelper.prototype.S_DIMMER = 4; // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nMySHelper.prototype.S_COVER = 5; // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nMySHelper.prototype.S_TEMP = 6; // Temperature sensor; V_TEMP\nMySHelper.prototype.S_HUM = 7; // Humidity sensor; V_HUM\nMySHelper.prototype.S_BARO = 8; // Barometer sensor; V_PRESSURE; V_FORECAST\nMySHelper.prototype.S_WIND = 9; // Wind sensor; V_WIND; V_GUST\nMySHelper.prototype.S_RAIN = 10; // Rain sensor; V_RAIN; V_RAINRATE\nMySHelper.prototype.S_UV = 11; // Uv sensor; V_UV\nMySHelper.prototype.S_WEIGHT = 12; // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nMySHelper.prototype.S_POWER = 13; // Power meter; V_WATT; V_KWH\nMySHelper.prototype.S_HEATER = 14; // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nMySHelper.prototype.S_DISTANCE = 15; // Distance sensor; V_DISTANCE\nMySHelper.prototype.S_LIGHT_LEVEL = 16; // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nMySHelper.prototype.S_ARDUINO_NODE = 17 ; // Used (internally) for presenting a non-repeating Arduino node\nMySHelper.prototype.S_ARDUINO_REPEATER_NODE = 18; // Used (internally) for presenting a repeating Arduino node \nMySHelper.prototype.S_LOCK = 19; // Lock device; V_LOCK_STATUS\nMySHelper.prototype.S_IR = 20; // Ir device; V_IR_SEND; V_IR_RECEIVE\nMySHelper.prototype.S_WATER = 21; // Water meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_AIR_QUALITY = 22; // Air quality sensor; V_LEVEL\nMySHelper.prototype.S_CUSTOM = 23; // Custom sensor \nMySHelper.prototype.S_DUST = 24; // Dust sensor; V_LEVEL\nMySHelper.prototype.S_SCENE_CONTROLLER = 25; // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nMySHelper.prototype.S_RGB_LIGHT = 26; // RGB light. Send color component data using V_RGB. Also supports V_WATT \nMySHelper.prototype.S_RGBW_LIGHT = 27; // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nMySHelper.prototype.S_COLOR_SENSOR = 28; // Color sensor; send color information using V_RGB\nMySHelper.prototype.S_HVAC = 28; // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nMySHelper.prototype.S_MULTIMETER = 29; // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nMySHelper.prototype.S_SPRINKLER = 30; // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nMySHelper.prototype.S_WATER_LEAK = 31; // Water leak sensor; V_TRIPPED; V_ARMED\nMySHelper.prototype.S_SOUND = 32; // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nMySHelper.prototype.S_VIBRATION = 33; // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nMySHelper.prototype.S_MOISTURE = 34; // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nMySHelper.prototype.S_INFO = 35; // LCD text device / Simple information device on controller; V_TEXT\nMySHelper.prototype.S_GAS = 36; // Gas meter; V_FLOW; V_VOLUME\nMySHelper.prototype.S_GPS = 37; // GPS Sensor; V_POSITION\n \nvar stype = {\nS_DOOR: MySHelper.prototype.S_DOOR, // Door sensor; V_TRIPPED; V_ARMED\nS_MOTION: MySHelper.prototype.S_MOTION, // Motion sensor; V_TRIPPED; V_ARMED \nS_SMOKE: MySHelper.prototype.S_SMOKE, // Smoke sensor; V_TRIPPED; V_ARMED\nS_LIGHT: MySHelper.prototype.S_LIGHT, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT\nS_BINARY: MySHelper.prototype.S_BINARY, // Binary light or relay; V_STATUS (or V_LIGHT); V_WATT (same as MySHelper.prototype.S_LIGHT)\nS_DIMMER: MySHelper.prototype.S_DIMMER, // Dimmable light or fan device; V_STATUS (on/off); V_DIMMER (dimmer level 0-100); V_WATT\nS_COVER: MySHelper.prototype.S_COVER, // Blinds or window cover; V_UP; V_DOWN; V_STOP; V_DIMMER (open/close to a percentage)\nS_TEMP: MySHelper.prototype.S_TEMP, // Temperature sensor; V_TEMP\nS_HUM: MySHelper.prototype.S_HUM, // Humidity sensor; V_HUM\nS_BARO: MySHelper.prototype.S_BARO, // Barometer sensor; V_PRESSURE; V_FORECAST\nS_WIND: MySHelper.prototype.S_WIND, // Wind sensor; V_WIND; V_GUST\nS_RAIN: MySHelper.prototype.S_RAIN, // Rain sensor; V_RAIN; V_RAINRATE\nS_UV: MySHelper.prototype.S_UV, // Uv sensor; V_UV\nS_WEIGHT: MySHelper.prototype.S_WEIGHT, // Personal scale sensor; V_WEIGHT; V_IMPEDANCE\nS_POWER: MySHelper.prototype.S_POWER, // Power meter; V_WATT; V_KWH\nS_HEATER: MySHelper.prototype.S_HEATER, // Header device; V_HVAC_SETPOINT_HEAT; V_HVAC_FLOW_STATE; V_TEMP\nS_DISTANCE: MySHelper.prototype.S_DISTANCE, // Distance sensor; V_DISTANCE\nS_LIGHT_LEVEL: MySHelper.prototype.S_LIGHT_LEVEL, // Light level sensor; V_LIGHT_LEVEL (uncalibrated in percentage); V_LEVEL (light level in lux)\nS_ARDUINO_NODE: MySHelper.prototype.S_ARDUINO_NODE, // Used (internally) for presenting a non-repeating Arduino node\nS_ARDUINO_REPEATER_NODE:MySHelper.prototype.S_ARDUINO_REPEATER_NODE, // Used (internally) for presenting a repeating Arduino node \nS_LOCK: MySHelper.prototype.S_LOCK, // Lock device; V_LOCK_STATUS\nS_IR: MySHelper.prototype.S_IR, // Ir device; V_IR_SEND; V_IR_RECEIVE\nS_WATER: MySHelper.prototype.S_WATER, // Water meter; V_FLOW; V_VOLUME\nS_AIR_QUALITY: MySHelper.prototype.S_AIR_QUALITY, // Air quality sensor; V_LEVEL\nS_CUSTOM: MySHelper.prototype.S_CUSTOM, // Custom sensor \nS_DUST: MySHelper.prototype.S_DUST, // Dust sensor; V_LEVEL\nS_SCENE_CONTROLLER: MySHelper.prototype.S_SCENE_CONTROLLER, // Scene controller device; V_SCENE_ON; V_SCENE_OFF. \nS_RGB_LIGHT: MySHelper.prototype.S_RGB_LIGHT, // RGB light. Send color component data using V_RGB. Also supports V_WATT \nS_RGBW_LIGHT: MySHelper.prototype.S_RGBW_LIGHT, // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT\nS_COLOR_SENSOR: MySHelper.prototype.S_COLOR_SENSOR, // Color sensor; send color information using V_RGB\nS_HVAC: MySHelper.prototype.S_HVAC, // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT; V_HVAC_SETPOINT_COLD; V_HVAC_FLOW_STATE; V_HVAC_FLOW_MODE; V_TEMP\nS_MULTIMETER: MySHelper.prototype.S_MULTIMETER, // Multimeter device; V_VOLTAGE; V_CURRENT; V_IMPEDANCE \nS_SPRINKLER: MySHelper.prototype.S_SPRINKLER, // Sprinkler; V_STATUS (turn on/off); V_TRIPPED (if fire detecting device)\nS_WATER_LEAK: MySHelper.prototype.S_WATER_LEAK, // Water leak sensor; V_TRIPPED; V_ARMED\nS_SOUND: MySHelper.prototype.S_SOUND, // Sound sensor; V_TRIPPED; V_ARMED; V_LEVEL (sound level in dB)\nS_VIBRATION: MySHelper.prototype.S_VIBRATION, // Vibration sensor; V_TRIPPED; V_ARMED; V_LEVEL (vibration in Hz)\nS_MOISTURE: MySHelper.prototype.S_MOISTURE, // Moisture sensor; V_TRIPPED; V_ARMED; V_LEVEL (water content or moisture in percentage?) \nS_INFO: MySHelper.prototype.S_INFO, // LCD text device / Simple information device on controller; V_TEXT\nS_GAS: MySHelper.prototype.S_GAS, // Gas meter; V_FLOW; V_VOLUME\nS_GPS: MySHelper.prototype.S_GPS // GPS Sensor; V_POSITION\n};\n\nMySHelper.prototype.SString = function(S_SUBTYPE) {\n for (var prop in stype ) \n if( stype[ prop ] === parseInt(S_SUBTYPE) )\n return prop;\n}; \n \n MySHelper.prototype.encode = function(destination, sensor, command, acknowledge, type, payload) {\n\tvar msg = destination.toString(10) + \";\" + sensor.toString(10) + \";\" + command.toString(10) + \";\" + acknowledge.toString(10) + \";\" + type.toString(10) + \";\";\n\tif (command == 4) {\n\t\tfor (var i = 0; i < payload.length; i++) {\n\t\t\tif (payload[i] < 16)\n\t\t\t\tmsg += \"0\";\n\t\t\tmsg += payload[i].toString(16);\n\t\t}\n\t} else {\n\t\tmsg += payload;\n\t}\n\tmsg += '\\n';\n\treturn msg.toString();\n}\n}\n\n\nvar MySHelperObj = new MySHelper();\n\ncontext.global.MYS = MySHelperObj;\n\nreturn msg;","outputs":1,"noerr":0,"x":383.25,"y":20,"wires":[[]]},{"id":"df1e322.f20e1d","type":"function","z":"9592163f.6a6de8","name":"Set Controller 1","func":"msg.controller = 1\n\nreturn msg;","outputs":1,"noerr":0,"x":641.0000076293945,"y":147.49999809265137,"wires":[["ebcef3df.14311"]]},{"id":"266b87b3.d99478","type":"switch","z":"9592163f.6a6de8","name":"route to controller n","property":"controller","rules":[{"t":"eq","v":"1"},{"t":"eq","v":"2"},{"t":"eq","v":"3"},{"t":"eq","v":"4"}],"checkall":"false","outputs":4,"x":133,"y":214.25,"wires":[["3e866f6d.c1799"],["c7d0d88b.382f28"],[],[]]},{"id":"c7d0d88b.382f28","type":"tcp request","z":"9592163f.6a6de8","server":"192.168.92.14","port":"5003","out":"sit","splitc":"0","name":"MySWifi ESP8266 GW AES 14","x":410.5,"y":207.24999618530273,"wires":[["c5f14d8f.3a0eb"]]},{"id":"c5f14d8f.3a0eb","type":"function","z":"9592163f.6a6de8","name":"Set Controller 2","func":"msg.controller = 2\n\nreturn msg;","outputs":1,"noerr":0,"x":653.5,"y":205.7500114440918,"wires":[["ebcef3df.14311"]]},{"id":"56b9f6ab.a94608","type":"file in","z":"9592163f.6a6de8","name":"read store for next ids","filename":"mysids.dump","format":"utf8","x":395,"y":65,"wires":[["57db23d6.a824dc"]]},{"id":"e000bd09.1fff4","type":"debug","z":"9592163f.6a6de8","name":"Debug","active":false,"console":"false","complete":"true","x":732,"y":361,"wires":[]},{"id":"57db23d6.a824dc","type":"function","z":"9592163f.6a6de8","name":"store to context.global.mysnextid","func":"if (msg.payload === undefined) {\n var mysnextid = {};\n\n obj = mysnextid; \n}\nelse \n{\ntry{\n obj = JSON.parse(msg.payload);\n }\n catch(e){\n \n var mysnextid = {};\n\n obj = mysnextid;\n \n }\n} \n\ncontext.global.mysnextid = obj;\n\nmsg.payload = context.global.mysnextid;\n\nreturn msg;","outputs":1,"noerr":0,"x":658,"y":53,"wires":[[]]},{"id":"dfba7d69.20458","type":"file","z":"9592163f.6a6de8","name":"dump mysids","filename":"mysids.dump","appendNewline":true,"createDir":false,"overwriteFile":"true","x":1473,"y":381.99999618530273,"wires":[]},{"id":"e0e76d62.1f189","type":"function","z":"9592163f.6a6de8","name":"handle nextids","func":"// increase nextid, if nodeid >= nextid \n// node.log(\"Handling next ids\");\n// node.log(\"nodeId: \" + msg.nodeId);\n\nbChanged = false;\n\nif (msg.nodeId === 0) return;\n\nif (msg.nodeId < 255)\n{\n // node.log(\"Test if next node-id must be set\");\n if (context.global.mysnextid[msg.controller] === undefined) {\n node.log(\"node-id not initialized yet\");\n context.global.mysnextid[msg.controller] = msg.nodeId+1;\n if (context.global.mysnextid[msg.controller] < context.global.MYS.MIN_NODEID)\n context.global.mysnextid[msg.controller] = context.global.MYS.MIN_NODEID;\n bChanged = true;\n }\n \n // node.log(\"Nexid stored \" + parseInt(context.global.mysnextid[msg.controller]));\n \n if (msg.nodeId >= parseInt(context.global.mysnextid[msg.controller])) {\n node.log(\"node-id >= next -> increase\");\n // convert to int\n context.global.mysnextid[msg.controller] = parseInt(context.global.mysnextid[msg.controller]);\n context.global.mysnextid[msg.controller] = msg.nodeId+1; \n if (context.global.mysnextid[msg.controller] < context.global.MYS.MIN_NODEID)\n context.global.mysnextid[msg.controller] = context.global.MYS.MIN_NODEID;\n bChanged = true;\n }\n\n if (bChanged) {\n node.log(\"next id must be stored\");\n msg.payload = JSON.stringify(context.global.mysnextid); \n return msg;\n }\n}\n\n\n","outputs":1,"noerr":0,"x":1262,"y":374.99999618530273,"wires":[["dfba7d69.20458","5c074c19.a3f8b4"]]},{"id":"8da09002.725f7","type":"function","z":"9592163f.6a6de8","name":"MQTT to MYS convert","func":"// topic = MYS-NODERED/set/controller/node-id/sensor-id/ack/sub-type\n// payload = payload :)\n\n var tokens = msg.topic.split(\"/\");\n \n msg.rawData = tokens;\n msg.tokens = tokens.length;\n if(tokens.length == 7)\n {\n if (tokens[0] != context.global.MYS.TOPIC_PREFIX) // not for us\n return;\n if (tokens[1] != 'set') // not for us\n return;\n \n msg.controller = parseInt(tokens[2]);\n msg.messageType = context.global.MYS.T_SET;\n msg.nodeId = parseInt(tokens[3]);\n msg.childSensorId = parseInt(tokens[4]);\n msg.ack = parseInt(tokens[5]);\n msg.subType = context.global.MYS.VNum(tokens[6]);\n \n msg.payload = context.global.MYS.encode(msg.nodeId, msg.childSensorId, msg.messageType, msg.ack, msg.subType, msg.payload);\n \n return msg; \n }\n","outputs":1,"noerr":0,"x":490,"y":361,"wires":[["e000bd09.1fff4","266b87b3.d99478"]]},{"id":"3e866f6d.c1799","type":"tcp request","z":"9592163f.6a6de8","server":"192.168.92.13","port":"5003","out":"sit","splitc":"0","name":"MySWifi ESP8266 GW AES 13","x":407,"y":145.99999618530273,"wires":[["df1e322.f20e1d","9386fdb0.6c79"]]},{"id":"5c074c19.a3f8b4","type":"debug","z":"9592163f.6a6de8","name":"","active":true,"console":"false","complete":"false","x":1454,"y":543.9999961853027,"wires":[]},{"id":"c75fd7f4.38a028","type":"mqtt in","z":"9592163f.6a6de8","name":"Read MQTT Stream: change Topic to your needs","topic":"MYS-NODERED/set/#","broker":"ba386057.845d3","x":183.5,"y":362,"wires":[["8da09002.725f7"]]},{"id":"9386fdb0.6c79","type":"function","z":"9592163f.6a6de8","name":"Watchdog controller 1","func":"if (isNaN(context.global.controller1count))\n context.global.controller1count=0;\n\n\ncontext.global.controller1count++;\n\n","outputs":1,"noerr":0,"x":630,"y":105,"wires":[[]]},{"id":"d465a67.f2b9a58","type":"inject","z":"9592163f.6a6de8","name":"Check health controller 1 every 5 minutes","topic":"","payload":"","payloadType":"none","repeat":"60","crontab":"","once":false,"x":173,"y":516,"wires":[["aa935a.ff556ca8"]]},{"id":"aa935a.ff556ca8","type":"function","z":"9592163f.6a6de8","name":"check health controlller 1","func":"if (isNaN(context.global.controller1count))\n context.global.controller1count=0;\n \nif (context.global.controller1count === 0) {\n // make a new connection to the controller\n msg.payload = \"\";\n node.log(\"no message recieved on mys controller 1, try to connect\");\n \n return msg;\n}\nelse\n{\n // reset counter\n context.global.controller1count=0;\n}\n","outputs":1,"noerr":0,"x":470,"y":510,"wires":[["c8b342e9.374cc","3e866f6d.c1799"]]},{"id":"c8b342e9.374cc","type":"debug","z":"9592163f.6a6de8","name":"","active":true,"console":"false","complete":"false","x":682,"y":511,"wires":[]}]```@FotoFieber
Great work, keep going! I have a modified version of your flow with message resend if not received - but it's a bit ugly to publish here.
