Washing machine state sensor

[Moshe Livne]

@BulldogLowell @ServiceXp Bosch in their infinite wisdom made the LED integral part of the start/stop button, putting a bit of a damper on optically sensing it. So far the 2 sound sensors I have are so bad that unless you do something really drastic like nuclear explosion they are very stoic about environmental beeps. they are ok for sensing knocks. now, I am not trying to sense Watt or try to profile the current use, as this is hopeless (my washing machine is also too smart for her own good). I am just going to watch for current draw above the "zero" over 5 min period. I think it would be safe enough but will not know until I get the sensors.....
@kalle - got the vibration sensor in the mail yesterday! great minds, etc. but it is more complicated as while doing hot wash there are lengthy waits for the water to heat up.
my plan is to use one of these powerboard things (http://www.mitre10.co.nz/shop/electrical_hardware/cords_powerboards/hpm_surge_protector_powerboard_6_way_106033/) and block the last two and use the space for the arduino and sensor to measure current on the last socket. I have excellent RCDs installed :-)
@hek - I use discreet notification using google hangouts....

[mvdarend]

@kalle, I actually tried the vibration sensor (based on this design) but I could only get it to perform properly by pressing a button to tell the Arduino that the cycle had started, which made it useless for when I wanted the machine to delay the start.
I tried checking for vibrations as a trigger for 'Machine start' but it would trigger when loading the machine, and again when unloading... basically that was useless.

@Moshe-Livne, I wanted to try sensing electricity usage, but when profiling the machine I found that when 'off' it was still consuming almost 5 watts, which is not a major problem if you define that as a threshold, but our machine sometimes just sits there doing nothing as far as I can see during the cycle. I was worried it would be a bit of a 'hit and miss' affair as @hek experienced.

@ServiceXp, I looked at your solution also when browsing the forums and almost went that way. But I didn;t want to open my machine, I know that my wife would not be happy about that. And with three small kids I can't afford to take my time about it, we need the machine every day :)

[Prateek Gupta]

@mvdarend hey I just stumbled across this post. I would like to draw your attention to something called as Power signature analysis.
There are some automation systems using it, such as neurio.io
I am still intrigued by it. Any electrical engineers here?

[Moshe Livne]

@mvdarend you are a ray of sunshine, aren't you? I think power profiling is the way to go. although the washing machine will sit around doing nothing for a while (especially during pre-wash) I think it is still safe to say that there will be spikes of usage when heating, spinning, etc
I am not too fussy about catching the machine the minute it finished so even 30 min with nothing over the threshold will be fine for me. I tend to leave the washing for DAYS in the machine :disappointed:
I now have 3 different vibration sensors. They do work for an extent but as you said - the number of false positives is a pain.
@Prateek-Gupta I think that is a bit of over solving a washing machine problem :-)

[Prateek Gupta]

@Moshe-Livne Yes, I agree. But then this could be applied to a numerous electrical appliances across your home. Almost, all the devices have a unique power signature down to different operating modes.

[mvdarend]

Created a custom widget in HomeGenie and set it up to send PushBullet notifications. After running for a week I've noticed a few small problems.

• If I leave the door open and the sun shines on the sensor, it's status changes to 'Running'. Increasing the threshold doesn't help so I'll need to protect the sensor from outside elements better. *
• The LED on the machine also flashes just before it goes into running mode. I think I'll go with an extra status depending on the previous one (Off -> Flashing = 'stand by', Running -> flashing = 'Idle') or something like that.

• My 3D printer is ordered and on its way, so I'll be able to create a custom holder. You guys are killing my finances :)

[Moshe Livne]

@mvdarend While waiting for the current sensor (and also discovering that new powerboards have one way screws! evil people!), I have re-checked my vibration sensors. i am using this one http://www.aliexpress.com/item/1pc-lot-SW-420-Normally-Closed-Alarm-Vibration-Sensor-Module-Vibration-Switch-30512/32259757483.html which is better than the others i think.
currently I am just monitoring 5 minute periods and if there is a vibration during this time I mark it as "active". my theory (that I can't check as I ran out of laundry) is that 3 periods of vibrations signal that a cycle is in progress. a period of quite means the cycle has finished. will post final results the minute the kids will produce enough dirty cloths.

[mvdarend]

@Moshe-Livne How is it working so far, have you been able to test it?

[Moshe Livne]

@mvdarend so far so good. have added a bit of logic to my sketch and need another load to test it :-)

this is the current sketch:

// Washing machine finished sketch 

#include <MySensor.h>
#include <SPI.h>


#define CHILD_ID 3
#define BUTTON_PIN  3  // Arduino Digital I/O pin for button/reed switch
#define SAMPLING_PERIOD 600000
MySensor gw;
int oldValue=-1;
unsigned long period_start = millis();
int state = -1;


// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(CHILD_ID,V_TRIPPED);

void setup()  
{  
  gw.begin();

 // Setup the button
  pinMode(BUTTON_PIN,INPUT);
  // Activate internal pull-up
  digitalWrite(BUTTON_PIN,HIGH);
  
  // After setting up the button, setup debouncer

  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  gw.present(CHILD_ID, S_DOOR);  
}

void report_state(int state)
{
	  	Serial.print("reporting state: ");
		Serial.println(state); 
	    gw.send(msg.set(state));
	
}

int prev_state = -1;
int prev_state_length = 0;

//  Check if digital input has changed and send in new value
void loop() 
{
  // Get the update value
  int value = digitalRead(BUTTON_PIN);
  
  if (value == 1) {// 0 means vibration detected
  	state = 1; 
  	Serial.println("setting state to 1");
  }
  Serial.println(millis()-period_start);
  
  if (millis() - period_start > SAMPLING_PERIOD) {
  	period_start = millis();
  	Serial.println(state);
    if (state != prev_state) {
  		if (state == 1 && prev_state_length > 2) { //a vibration period after long period of quit means a cycle started
  	    	report_state(state);
	    	prev_state_length = 1;
  		
  		} else if (state == 0 && prev_state_length > 2){ //a long quite period after a cycle means cycle finished
  			report_state(state);
  			prev_state_length = 1;
  		}
  	}
	prev_state = state;
    state = 0;
  	
  }
  
 
  delay(100);
} 

will refine it once i verify it works through all the different cycles - this is not even a tested version, just to give you an idea about how it works. looks promising so far.

[Moshe Livne]

found some flaws in the logic - updated and checking - do not use the code above

[BulldogLowell]

@Moshe-Livne

I think you can make this easier...

It looks like you are looking for two motion events in the past two minutes to indicate washer is on?

something like this (untested)

// Washing machine finished sketch

#include <MySensor.h>
#include <SPI.h>

#define CHILD_ID 3
#define BUTTON_PIN  3  // Arduino Digital I/O pin for button/reed switch
#define SAMPLING_PERIOD 600000UL
MySensor gw;
unsigned long motionTime;
unsigned long lastMotionTime = millis();
boolean lastSensorState = false;
boolean lastWasherState = false;
MyMessage msg(CHILD_ID, V_TRIPPED);

void setup()
{
  gw.begin();
  pinMode(BUTTON_PIN, INPUT_PULLUP);
  gw.present(CHILD_ID, S_DOOR);
}

void loop()
{
  boolean sensorState = digitalRead(BUTTON_PIN);// Get the updated sensor value
  if (sensorState != lastSensorState && lastSensorState == true) //detect state change from true to false
  {
    lastMotionTime = motionTime; //cascade time back 
    motionTime = millis();
  }
  lastSensorState = sensorState;
  //
  boolean washerState = (motionTime - lastMotionTime < SAMPLING_PERIOD && motionTime - millis() < SAMPLING_PERIOD); 
  if (washerState != lastWasherState)
  {
    gw.send(msg.set(washerState));
  }
  lastWasherState = washerState;
}

[Moshe Livne]

@BulldogLowell It is slightly more complicated (but not much). the machine can idle for 5-10 min (well, not really idle, but idle enough so no vibrations will be felt). so, the current logic marks 5 minute periods. a vibration period marks the beginning of the cycle and 2 or 3 (yet to be determined) periods of quite marks end of cycle.

[BulldogLowell]

@Moshe-Livne

so if no vibration is sensed in the past five (configurable) minutes machine is OFF, otherwise machine is ON?

likewise you want to indicate Washing when two vibrations are sensed in less than two or three (configurable) minutes?

yes?

[Moshe Livne]

@BulldogLowell re-reading your code, it would work well. the reason I made the "periods" was more to help me debug the scenario as I didn't want to sift through zillions of on/off.

[BulldogLowell]

yeah, that is why it is important to just print() when there are state changes... added configuration and debug:

// Washing machine finished sketch

#include <MySensor.h>
#include <SPI.h>

#define CHILD_ID 3
#define BUTTON_PIN  3  // Arduino Digital I/O pin for button/reed switch
#define ONE_MINUTE 600000UL
MySensor gw;
unsigned long motionTime;
unsigned long lastMotionTime = millis();
boolean lastSensorState = false;
boolean lastWasherState = false;
MyMessage msg(CHILD_ID, V_TRIPPED);

void setup()
{
  gw.begin();
  pinMode(BUTTON_PIN, INPUT_PULLUP);
  gw.present(CHILD_ID, S_DOOR);
}

void loop()
{
  boolean sensorState = digitalRead(BUTTON_PIN);// Get the updated sensor value
  if (sensorState != lastSensorState && lastSensorState == true) //detect state change from true to false
  {
    lastMotionTime = motionTime; //cascade time back 
    motionTime = millis();
  }
  lastSensorState = sensorState;
  //
  boolean washerState = ((motionTime - lastMotionTime < ONE_MINUTE * 2) && (motionTime - millis() < ONE_MINUTE * 5)); 
  if (washerState != lastWasherState)
  {
    gw.send(msg.set(washerState));
    Serial.print(F("Washer is "));
    Serial.println(washerState? F("ON") : F("OFF"));
  }
  lastWasherState = sensorState;
}

[Moshe Livne]

@BulldogLowell Alas, no. The sensors are on the edge of their capability, so you get some on, lots of off. an ON means a cycle started (I am not too worried about false positives from loading the machine for now. A quite period (no ON what so ever) of about 10 min means the cycle has finished. so basically its going to be eventually a very simple code like:

if (sensorState == ON)
    cycleState=WASHING
else period check and if long enough then cycleState = ENDED

I am still checking through different cycles and the kids do not produce enough dirty cloths, just to annoy me i think. Anyone has cloths he needs to wash?

[jasonrio]

I bought one this year and i am really happy with it.