PhoneyTV for Vera is Here!

[5546dug]

@BulldogLowell yes I have v3.1 So I was wrong -at least consistent!
I have Vera controller and at the moment My Sensors serial GW is connected ,

The vera dashboard shows node for light on and off and that is really what I want. To start the lights remotely , I think using the reset locally (d2 to gnd?) may work but only if we are there

[5546dug]

Should also tell you I use ui5 in my veras case it makes a difference and I can toggle the switch off and on in my Device page but no Phoney TV changes.

[BulldogLowell]

@5546dug said:

The vera dashboard shows node for light on and off and that is really what I want.

then you are there...

is it working?

[5546dug]

no it is not

[5546dug]

@BulldogLowell I see in v3.1 pin d2 is called ' button pin' and is an' input' and 'pullup'
(understand it is for the pushbutton use but even then it is only for a few sec. in my setup.)
Also there is d13 defined as for the relay and used with the radio could that be an issue?

How is the controller/GW telling the Phoney TV to change states? Do I need to run a wire from d2 (?) to gnd/vcc to create an interupt?
I don't really need the button, but I will leave it there

[5546dug]

@BulldogLowell Just noticed your post is v3.1 lib 1.4.1 and I have lib 1.4

That might be why I can't control from Vera ....then there is that d2 interrupt connection.

[BulldogLowell]

@5546dug

hmmm, looking at the code I posted I see why you have a problem.

Try this:

/*
 * PhoneyTV v3.1.1
 *
 * This Sketch illuminates 6 sets of LED's in a random fashion as to mimic the
 * light eminating from a television.  It is intended to make an empty home,
 * or an empty section of a home, appear to be occupied by someone watching
 * TV.  As an alternative to a real television left on, this uses less than 1%
 * of the electrical energy.
 *
 * With the use of the MySensors plugin and gateway, PhoneyTV is intended to
 * be used with a controller (e.g. Vera or Raspberry PI).
 *
 * Sketch does not use any delays to create the random blinking as a way to
 * assure that communication back to the gateway is as unaffected as possible.
 *
 * You can adjust the length of the blink interval and its "twitchyness" by
 * modifying the random number generators, if you prefer more/less 'motion' in
 * in your unit.  The lines are highlighted in the code, play around to create the
 * random effect you like.
 *
 * Sketch takes advantage of available PWM on pins 3, 5 & 6 using the white/blue LEDs
 * to allow fluctuations in the intensity of the light, enhancing the PhoneyTV's
 * realistic light effects.
 *
 * Created 12-APR-2014
 * Free for distrubution
 * Credit should be given to MySensors.org for their base code for relay control
 * and for the radio configuration.  Thanks Guys.
 *
 * 29-May-2014
 * Version 2:  Simplified the code, removing all redundant relay setup from original
 * code.  Added an on/off momentary pushputton option to be set up on pin 2.  Inproved
 * the dark dips for longer duration (can be configured) at intervals.
 *
 * 6-Jun-2015
 * Version 3.1
 * Updated for MySensors V1.4.1
 * Contributed by Jim (BulldogLowell@gmail.com) Inspired by Josh >> Deltanu1142@gmail.com
 */
//
#include <MySensor.h>
#include <SPI.h>
#include <Bounce2.h>
//
#define SKETCH_NAME "PhoneyTV"
#define SKETCH_VERSION "3.1.1"
//
#define RADIO_RESET_DELAY_TIME 20
//
#define BUTTON_PIN  2  // Arduino Digital I/O pin number for button 
#define CHILD_ID 1   // 
#define RADIO_ID 5  //AUTO
//
#define DEBUG_ON
//
#ifdef DEBUG_ON
#define DEBUG_PRINT(x)   Serial.print(x)
#define DEBUG_PRINTLN(x) Serial.println(x)
#define SERIAL_START(x)  Serial.begin(x)
#else
#define DEBUG_PRINT(x)
#define DEBUG_PRINTLN(x)
#define SERIAL_START(x)
#endif
//
MySensor gw;
MyMessage msg(CHILD_ID, V_LIGHT);
//
byte ledPin3 =  3;      // White using PWM
byte ledPin4 =  4;      // Red
byte ledPin5 =  5;      // Blue using PWM
byte ledPin6 =  6;      // Blue using PWM
byte ledPin7 =  7;      // Green
byte ledPin8 =  8;      // White (No PWM)
//
Bounce debouncer = Bounce();
byte oldValue = 0;
boolean state = false;
boolean oldState = false;
int dipInterval = 10;
int darkTime = 250;
unsigned long currentDipTime;
unsigned long dipStartTime;
unsigned long currentMillis;
byte ledState = LOW;
unsigned long previousMillis = 0UL;
byte led = 5;
unsigned long interval = 2000UL;
int twitch = 50;
int dipCount = 0;
int analogLevel = 100;
boolean timeToDip = false;
boolean gotAck=false;
//
void setup()
{
  SERIAL_START(115200);
  pinMode(ledPin3, OUTPUT);
  pinMode(ledPin4, OUTPUT);
  pinMode(ledPin5, OUTPUT);
  pinMode(ledPin6, OUTPUT);
  pinMode(ledPin7, OUTPUT);
  pinMode(ledPin8, OUTPUT);
  pinMode(BUTTON_PIN, INPUT_PULLUP);
  //
  debouncer.attach(BUTTON_PIN);
  debouncer.interval(50);
  //
  gw.begin(incomingMessage, RADIO_ID, true, 0);  // configured as a repeating node!!
  gw.sendSketchInfo(SKETCH_NAME, SKETCH_VERSION);
  gw.wait(RADIO_RESET_DELAY_TIME);
  gw.present(CHILD_ID, S_LIGHT);
  gw.wait(RADIO_RESET_DELAY_TIME);
  while(!gw.send(msg.set(state), false))
  {
    gw.wait(RADIO_RESET_DELAY_TIME);
  }
  gw.wait(RADIO_RESET_DELAY_TIME);
  DEBUG_PRINTLN(F("Sensor Presentation Complete"));
}
//
void loop()
{
  gw.process();
  debouncer.update();
  byte value = debouncer.read();
  if (value != oldValue && value == 0)
  {
    state = !state;
    while(!gotAck)
    {
      gw.send(msg.set(state), true);
      gw.wait(RADIO_RESET_DELAY_TIME);
    }
    gotAck = false;
    DEBUG_PRINT(F("State Changed to:"));
    DEBUG_PRINTLN(state? F("PhoneyTV ON") : F("PhoneyTV OFF"));
  }
  oldValue = value;
  if (state)
  {
    if (timeToDip == false)
    {
      currentMillis = millis();
      if (currentMillis - previousMillis > interval)
      {
        previousMillis = currentMillis;
        interval = random(750, 4001); //Adjusts the interval for more/less frequent random light changes
        twitch = random(40, 100); // Twitch provides motion effect but can be a bit much if too high
        dipCount = dipCount++;
      }
      if (currentMillis - previousMillis < twitch)
      {
        led = random(3, 9);
        analogLevel = random(50, 255); // set the range of the 3 pwm leds
        ledState = !ledState;
        switch (led) //for the three PWM pins
        {
          case 3:
            pwmWrite();
            break;
          case 5:
            pwmWrite();
            break;
          case 6:
            pwmWrite();
            break;
          default:
            digitalWrite(led, ledState);
        }
        if (dipCount > dipInterval)
        {
          timeToDip = true;
          dipCount = 0;
          dipStartTime = millis();
          darkTime = random(50, 150);
          dipInterval = random(5, 250); // cycles of flicker
        }
      }
    }
    else
    {
      DEBUG_PRINTLN(F("Dip Time"));
      currentDipTime = millis();
      if (currentDipTime - dipStartTime < darkTime)
      {
        for (int i = 3; i < 9; i++)
        {
          digitalWrite(i, LOW);
        }
      }
      else
      {
        timeToDip = false;
      }
    }
  }
  else
  {
    if (state != oldState)
    {
      for (int i = 3; i < 9; i++)
      {
        digitalWrite(i, LOW);
      }
    }
  }
  oldState = state;
}
//
void incomingMessage(const MyMessage &message)
{
  if (message.isAck())
  {
    DEBUG_PRINTLN(F("This is an ack from gateway"));
    gotAck = true;
  }
  if (message.type == V_LIGHT)
  {
    state = message.getBool();
    DEBUG_PRINT(F("Incoming change for sensor... New State = "));
    DEBUG_PRINTLN(state? F("ON") : F("OFF"));
  }
}
//
void pwmWrite()
{
  if (ledState == HIGH) 
  {
    analogWrite(led, analogLevel);
  }
  else 
  {
    digitalWrite(led, LOW);
  }
}

[5546dug]

@BulldogLowell Thanks
I will try. 3.1.1 when I get home

[5546dug]

@BulldogLowell
here is screen shot of error codeArduino: 1.6.5 (Windows 8.1), Board: "Arduino Nano, ATmega328"

Using library MySensors in folder: C:\Users\Carolyn & Doug\Documents\Arduino\libraries\MySensors (legacy)

Using library SPI in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI

Using library Bounce2 in folder: C:\Users\Carolyn & Doug\Documents\Arduino\libraries\Bounce2 (legacy)

C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++ -c -g -Os -w -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10605 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR -IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino -IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs -IC:\Users\Carolyn & Doug\Documents\Arduino\libraries\MySensors -IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI -IC:\Users\Carolyn & Doug\Documents\Arduino\libraries\Bounce2 C:\Users\CAROLY~1\AppData\Local\Temp\build5063782765207672318.tmp\phoney_tv_july_20_3.1.1.cpp -o C:\Users\CAROLY~1\AppData\Local\Temp\build5063782765207672318.tmp\phoney_tv_july_20_3.1.1.cpp.o

phoney_tv_july_20_3.1.1.ino: In function 'void setup()':
phoney_tv_july_20_3.1.1.ino:111:6: error: 'class MySensor' has no member named 'wait'
phoney_tv_july_20_3.1.1.ino:113:6: error: 'class MySensor' has no member named 'wait'
phoney_tv_july_20_3.1.1.ino:116:8: error: 'class MySensor' has no member named 'wait'
phoney_tv_july_20_3.1.1.ino:118:6: error: 'class MySensor' has no member named 'wait'
phoney_tv_july_20_3.1.1.ino: In function 'void loop()':
phoney_tv_july_20_3.1.1.ino:133:10: error: 'class MySensor' has no member named 'wait'
'class MySensor' has no member named 'wait'

[BulldogLowell]

@5546dug

I think you need to update your MySensors IDE.

[5546dug]

Ok I will try that also
Thanks

[5546dug]

@BulldogLowell I downloaded lib 1.4.1 and just like that your code worked 100% THANKS.

It is something I could not have done.

Just a question, when in your code 3.1.1 you have a few scattered lines through out the declaration code with only // on these lines does it mean anything in particular ?
I couldn't find anything wrote up like the notations of /* and */ for writing comments and paragraphs .

[BulldogLowell]

@5546dug said:

Just a question, when in your code 3.1.1 you have a few scattered lines through out the declaration code with only // on these lines does it mean anything in particular ?

Adding the "//" is only a personal preference of mine to use the comment marks rather than leaving a blank line. for me, with a certain text editor that I use, it is easier to edit and not inadvertently delete some curly brace and screw up my code!

@5546dug said:

your code worked 100% THANKS.

happy to hear you are going now, sorry about the mixup.