relay actuator fails to presenting itself

[yury]

Yes. I use switch as parent with ID ==5

like this :

#include <MySensor.h>
#include <SPI.h>
#include <Bounce2.h>

#define CHILD_ID 55
#define BUTTON_PIN  5  // Arduino Digital I/O pin for button/reed switch

MySensor gw;
Bounce debouncer = Bounce(); 
int oldValue=-1;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(CHILD_ID,V_LIGHT);

void setup()  
{  
  #define NodeID 5

  // Initialize library and add callback for incoming messages
  gw.begin(NULL, NodeID, false);



//  gw.begin();

 // Setup the button
  pinMode(BUTTON_PIN,INPUT);
  // Activate internal pull-up
  digitalWrite(BUTTON_PIN,HIGH);
  
  // After setting up the button, setup debouncer
  debouncer.attach(BUTTON_PIN);
  debouncer.interval(5);
  
  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  gw.present(CHILD_ID, S_LIGHT);  
}

[hek]

And what does the repeater (5) log look like?

As you can see (ack fail) the node is having problem communicating with repeater.

Also.. are you calling gw.process() in the loop-function on your repeater?

[yury]

re:
And what does the repeater (5) log look like?

I do not use repeater. 5 is sample code for switch with hard coded ID == 5

switch monitor log

send: 5-5-0-0 s=255,c=0,t=17,pt=0,l=3,sg=0,st=ok:1.5
send: 5-5-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
sensor started, id=5, parent=0, distance=1
send: 5-5-0-0 s=55,c=0,t=3,pt=0,l=0,sg=0,st=ok:
send: 5-5-0-0 s=55,c=1,t=2,pt=2,l=2,sg=0,st=ok:1
send: 5-5-0-0 s=55,c=1,t=2,pt=2,l=2,sg=0,st=ok:0
send: 5-5-0-0 s=55,c=1,t=2,pt=2,l=2,sg=0,st=ok:1

re:
As you can see (ack fail) the node is having problem communicating with repeater.

do I need to switch off somewhere repeater mode? I do not need repeater.
I use
gw.begin(incomingMessage, NodeID, false,5); in actuator code
gw.begin(NULL, NodeID, false); in switch code.

re:
Also.. are you calling gw.process() in the loop-function on your repeater?

I added now...

//  Check if digital input has changed and send in new value
void loop() 
{

  debouncer.update();
  // Get the update value
  int value = debouncer.read();
 
  if (value != oldValue) {
     // Send in the new value
     gw.send(msg.set(value==HIGH ? 1 : 0));
     oldValue = value;
  }
 gw.process();
}

After I added gw.process(); log looks good but still no traeces of actuator in serial gateway.

Actuator log:
send: 55-55-5-0 s=255,c=0,t=17,pt=0,l=3,sg=0,st=ok:1.5
send: 55-55-5-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:5
sensor started, id=55, parent=5, distance=1
send: 55-55-5-0 s=255,c=3,t=11,pt=0,l=5,sg=0,st=ok:Relay
send: 55-55-5-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.0
send: 55-55-5-0 s=55,c=0,t=3,pt=0,l=0,sg=0,st=ok:

[hek]

@yury said:

gw.begin(NULL, NodeID, false); <--

You must enable repeater mode (3:rd argument) of your repeater, otherwise it won't relay message from your node 55 to your gateway.

gw(0) <-- Repeater(5) <---- Node (55)

[yury]

added as repeater node 5, but still no traces of the actuator 55 in the gateway.

send: 5-5-0-0 s=255,c=0,t=18,pt=0,l=3,sg=0,st=ok:1.5
send: 5-5-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
repeater started, id=5, parent=0, distance=1
send: 5-5-0-0 s=55,c=0,t=3,pt=0,l=0,sg=0,st=ok:
send: 5-5-0-0 s=55,c=1,t=2,pt=2,l=2,sg=0,st=ok:1

[hek]

Ok, What does the Node(55) log look like now then?

[yury]

55 log looks llike this:

send: 55-55-5-0 s=255,c=0,t=17,pt=0,l=3,sg=0,st=ok:1.5
send: 55-55-5-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:5
sensor started, id=55, parent=5, distance=1
send: 55-55-5-0 s=255,c=3,t=11,pt=0,l=5,sg=0,st=ok:Relay
send: 55-55-5-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.0
send: 55-55-5-0 s=55,c=0,t=3,pt=0,l=0,sg=0,st=ok:

[hek]

Ok. Are you sure the repeater log above is correct? We can we that node 55 successfully sends its messages to it.

[yury]

Hek, you are the best!

I plug all three things into my laptop to be able to see all logs and actuator (55) appeared in the serial gateway log

0;0;3;0;9;gateway started, id=0, parent=0, distance=0
0;0;3;0;14;Gateway startup complete.
0;0;3;0;9;read: 5-5-0 s=255,c=0,t=18,pt=0,l=3,sg=0:1.5
5;255;0;0;18;1.5
0;0;3;0;9;read: 5-5-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0
5;255;3;0;6;0
0;0;3;0;9;read: 55-5-0 s=255,c=0,t=17,pt=0,l=3,sg=0:1.5
55;255;0;0;17;1.5
0;0;3;0;9;read: 55-5-0 s=255,c=3,t=6,pt=1,l=1,sg=0:5
55;255;3;0;6;5
0;0;3;0;9;read: 5-5-0 s=55,c=0,t=3,pt=0,l=0,sg=0:
5;55;0;0;3;
0;0;3;0;9;read: 5-5-0 s=55,c=1,t=2,pt=2,l=2,sg=0:1
5;55;1;0;2;1
0;0;3;0;9;read: 55-5-0 s=255,c=3,t=11,pt=0,l=5,sg=0:Relay
55;255;3;0;11;Relay
0;0;3;0;9;read: 55-5-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
55;255;3;0;12;1.0
0;0;3;0;9;read: 55-5-0 s=55,c=0,t=3,pt=0,l=0,sg=0:
55;55;0;0;3;

repeater (5) log also showing it
send: 5-5-0-0 s=255,c=0,t=18,pt=0,l=3,sg=0,st=ok:1.5
send: 5-5-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
repeater started, id=5, parent=0, distance=1
send: 5-5-0-0 s=55,c=0,t=3,pt=0,l=0,sg=0,st=ok:
send: 5-5-0-0 s=55,c=1,t=2,pt=2,l=2,sg=0,st=ok:1
read: 55-55-0 s=255,c=0,t=17,pt=0,l=3,sg=0:1.5
send: 55-5-0-0 s=255,c=0,t=17,pt=0,l=3,sg=0,st=ok:1.5
read: 55-55-0 s=255,c=3,t=6,pt=1,l=1,sg=0:5
send: 55-5-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:5
read: 55-55-0 s=255,c=3,t=11,pt=0,l=5,sg=0:Relay
send: 55-5-0-0 s=255,c=3,t=11,pt=0,l=5,sg=0,st=ok:Relay
read: 55-55-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
send: 55-5-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.0
read: 55-55-0 s=55,c=0,t=3,pt=0,l=0,sg=0:
send: 55-5-0-0 s=55,c=0,t=3,pt=0,l=0,sg=0,st=ok:
send: 5-5-0-0 s=55,c=1,t=2,pt=2,l=2,sg=0,st=ok:0
send: 5-5-0-0 s=55,c=1,t=2,pt=2,l=2,sg=0,st=ok:1

understand something wrong was with external power supply.

the only thing left, actuator(55) not receiving from repeater(5) which is the switch sensor, messages. These two entries

send: 5-5-0-0 s=55,c=1,t=2,pt=2,l=2,sg=0,st=ok:0
send: 5-5-0-0 s=55,c=1,t=2,pt=2,l=2,sg=0,st=ok:1

not getting to actuator...

[hek]

There was a bug fix a couple of days ago fixing problem when routing from repeater to a node. Please make sure that you run the latest library code.