Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Software initiated reboot of Mega does not work

tomkxy last edited by

I tried to implement the reboot message in the MQTTClientGateway. I am calling hw_reboot() when receiving the internal reboot message. I am not really sure what happens but the Leds on the Mega start blinking like hell and even pressing the reset button does not boot up the gateway.

Am I missing something?
Reply Quote 0
1 Reply Last reply

1
Posts

694
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3310
Views

No one has replied
Radio waking up for no reason.
Development • • Sasquatch

3

0
Votes

3
Posts

37
Views

Over 4 years on, and my node ran continuously sending 4 messages every 5 minutes. It's 700mAh LiFePo4 battery voltage dropped from initial 3.45V to 3.24V, according to LiFePo4 voltge/SoC tables It's just under 40% left. 700*60% = 420mAh. 100 mAH per year. using library 2.40 and blob message I could cut usage to ~25mAh/year, not bad
Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

3

0
Votes

3
Posts

19
Views

@mfalkvidd Yes, I understand that 253 is the software limit. I was wondering about the hardware limit. For example, my Asus router has a software limit of 253 devices. But when I get 20-25 WiFi devices trying to connect, the network goes haywire. (pun intended ) I am quite convinced that this is a hardware limitation of the router because the router has to carry some information about each connection. If the gateway is dumb, that is, carries no information about any connection, then it could truly have 253 connections. After a bit of contemplation, I realize that the name, gateway, implies this. If that is the case, it is good news for the DiY'er in that this very inexpensive and cheap hardware could stand in for a LoRaWAN, again, with a number of compromises.
MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

11

0
Votes

11
Posts

53
Views

@dpcons MQTT sounds intimidating and looks imitimidating when you see all of the options available. Here's the scenario: You want to send a message. That's the -m option followed by a space and the message between " " the location, topic, is a tree, -t option, separated by forward slash / eg. MyRootTopic/MyTopicsSub/MyTopicSubSub It's as easy as that if your broker, the MQTT service (program) is on the same computer as the sending program. Usually it's not. Specifiy the location, the host, of the broker with the -h option followed by the host name or IP address The retain option, -r is important but explaining it is beyone the scope of this message Receiving, subscribing, to a topic is just the same, but you wouldn't have the -m message If you subscribe from the command line, the subscribe function waits indefinitely for messages published to the subscribed topic (unless you use the -C option) ^C to terminate the command. A tamotized device with the MQTT configured will create a number of topics on the broker. Home Assistant will see this automatically, if you have the Tasmota and MQTT Integrations installed. The MySensors MQTT gateway takes care of MQTT communication for a MySensors device. Again the MySensors and MQTT integrations. I use both. -OSD
Sending offset to node
Development • • bsl88k

3

0
Votes

3
Posts

41
Views

Thanks for the idea, i will look into it soon, will let know how it goes..
Gateway without a radio
Development • • OldSurferDude

3

0
Votes

3
Posts

28
Views

@OldSurferDude yes, just run the configure command with --my-transport=none

Software initiated reboot of Mega does not work

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Radio waking up for no reason.
Development • • Sasquatch

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

Sending offset to node
Development • • bsl88k

Gateway without a radio
Development • • OldSurferDude

32
Online

11.6k
Users

11.2k
Topics

113.0k
Posts

Software initiated reboot of Mega does not work

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

Radio waking up for no reason. Development • • Sasquatch

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors Development • • OldSurferDude

MQTT-Help me understand about the MQTT Gateway. Development • • dpcons

Sending offset to node Development • • bsl88k

Gateway without a radio Development • • OldSurferDude

32Online

11.6kUsers

11.2kTopics

113.0kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Radio waking up for no reason.
Development • • Sasquatch

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

Sending offset to node
Development • • bsl88k

Gateway without a radio
Development • • OldSurferDude

32
Online

11.6k
Users

11.2k
Topics

113.0k
Posts