Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Software initiated reboot of Mega does not work

tomkxy last edited by

I tried to implement the reboot message in the MQTTClientGateway. I am calling hw_reboot() when receiving the internal reboot message. I am not really sure what happens but the Leds on the Mega start blinking like hell and even pressing the reset button does not boot up the gateway.

Am I missing something?
Reply Quote 0
1 Reply Last reply

1
Posts

694
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3310
Views

No one has replied
Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

3

1
Votes

3
Posts

25
Views

@mfalkvidd Thank you very much, that's exactly what I was looking for!
Saving last known good state, but not in EEPROM
Development • • OldSurferDude

6

0
Votes

6
Posts

33
Views

@OldSurferDude jus request counter states from controller on each reset, worked fine with Domoticz... or save in eeprom but increase location every write, on power up/reset search eeprom for largest value stored and carry on from that location, one long integer will fit 256 times in atmega328(p) eeprom, is that long enough for you ?
Home Assistant/MySensors quirks
Development • • OldSurferDude

1

0
Votes

1
Posts

8
Views

No one has replied
Radio waking up for no reason.
Development • • Sasquatch

3

0
Votes

3
Posts

37
Views

Over 4 years on, and my node ran continuously sending 4 messages every 5 minutes. It's 700mAh LiFePo4 battery voltage dropped from initial 3.45V to 3.24V, according to LiFePo4 voltge/SoC tables It's just under 40% left. 700*60% = 420mAh. 100 mAH per year. using library 2.40 and blob message I could cut usage to ~25mAh/year, not bad
Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

3

0
Votes

3
Posts

21
Views

@mfalkvidd Yes, I understand that 253 is the software limit. I was wondering about the hardware limit. For example, my Asus router has a software limit of 253 devices. But when I get 20-25 WiFi devices trying to connect, the network goes haywire. (pun intended ) I am quite convinced that this is a hardware limitation of the router because the router has to carry some information about each connection. If the gateway is dumb, that is, carries no information about any connection, then it could truly have 253 connections. After a bit of contemplation, I realize that the name, gateway, implies this. If that is the case, it is good news for the DiY'er in that this very inexpensive and cheap hardware could stand in for a LoRaWAN, again, with a number of compromises.

Software initiated reboot of Mega does not work

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Home Assistant/MySensors quirks
Development • • OldSurferDude

Radio waking up for no reason.
Development • • Sasquatch

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

19
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Software initiated reboot of Mega does not work

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

Counting Incoming and Outgoing Messages from a Gateway Development • • Trand

Saving last known good state, but not in EEPROM Development • • OldSurferDude

Home Assistant/MySensors quirks Development • • OldSurferDude

Radio waking up for no reason. Development • • Sasquatch

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors Development • • OldSurferDude

19Online

11.7kUsers

11.2kTopics

113.0kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Home Assistant/MySensors quirks
Development • • OldSurferDude

Radio waking up for no reason.
Development • • Sasquatch

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

19
Online

11.7k
Users

11.2k
Topics

113.0k
Posts