My Slim 2AA Battery Node

[Soloam]

A nice additions would be a place to solder a ATSHA204A on board like the Sensebender! I'll try to make the change in KiCad!

[meddie]

@Soloam
and a flash module for OTA Sketch Uploads :-)

[Matt Pitts]

Thanks @GertSanders for showing me the BOM I hadn't realised it was there, but do I need everything listed there to get it working properly?

[GertSanders]

@Matt-Pitts
I'm assuming that if a designer goes through the trouble of listing items on a bom, they are needed.

But you are right, that is not always the case. I'm not at my Mac (using a miniscreen now), so i can not multitask.

[Tom71]

Hello,
I have problems to upload the scatch to the bare Amtel. I use an USB-TTL FTL Adaper and connect, RX/TX and Reset Pin with 100n->DTR. But I got always errors on uploading.

The bootloader I have successfull burned with an raspberry pi and gpio (http://www.lxccu.com/hb-raspberry-bootloader-update):

sudo bin/avrdude -Cbin/avrdude.conf -p m328p -P gpio -c gpio -U lfuse:w:0x62:m -U hfuse:w:0xde:m -U efuse:w:0x07:m -U lock:w:0x2F:m -e -Uflash:w:1443392692398-atmega328_1a.hex:i
avrdude: safemode: Fuses OK

How can I got it working?
Thank you

Thomas

[bjacobse]

Have you tried to upload a standard arduino bootloader?, are you using correct baud settings for uploading?

[Tom71]

@bjacobse No, used the bootloader from here (http://forum.mysensors.org/uploads/files/1443392692398-atmega328_1a.hex). This is an bootloader for the internal clock.
Baud settings to upload the sketch or the bootloader?

[m26872]

@Tom71 I think the question was if you have been successful with programming a standard bootloader to a standard Arduino board and then uploading and running a sketch?

[Tom71]

@m26872 Sure, but not with an bootloader (optiboot with intenal clock) on an bare Atmega. Later I will try this: http://forum.mysensors.org/uploads/files/1454449901412-7.png
I build some MySensors with an Arduino Micro, but not with only an Atmega.

Update: I don't know what's different, but this works. Perhaps I forget to connect Reset from FDL -> Pin 1.
Now I can upload simple sketches.

[bjacobse]

I have not had success to upload a sketch via FTDI on an Arduino ProMini using Optiboot. When I flash an ordinary bootloader (Taken from the Arduino IDE), I can easily upload a sketch via FTDI.
so that's why I recommend to flash a standard bootloader and check if you then can upload a sketch afterwards.

[Tom71]

@bjacobse Witch bootloader you have taken?

[Matt Pitts]

Hi I'm just about to start ording parts of the slim node. Looking through the thread I'm thinking based on my limited knowledge of arduino, I might be better off buying chips which already have a bootloader installed?

Can people advise, how difficult is it to upload the boot loader? Thanks

[sundberg84]

@Matt-Pitts - Not that hard if you read about it. Here are some good links:

• https://www.arduino.cc/en/Hacking/Bootloader?from=Tutorial.Bootloader
• https://www.arduino.cc/en/Tutorial/ArduinoISP
• https://www.arduino.cc/en/Tutorial/ArduinoToBreadboard

[bjacobse]

@Tom71
well I have not yet started to use the Mysensor specific bootloader. When I use the optiboot, I upload sketch with my USBtiny (so no FTDI), and when I use FTDI for uploading sketch I used the "Arduino Pro or pro mini (3,3V, 8MHz) w/ATmega328"

[Tom71]

@bjacobse I thought the USBtiny is only to upload the bootloader, not the mysensors software.
I did two things:

1. Burn the bootloader atmega328_1a.hex to an bare Atmega328p with an Arduino as ISP
2. Upload an simple scetch to the Atmega with an RX/TX uploader (I used an USB to TTL with an FTDI and also an Ardunino Uno without the Atmega chip, like here http://forum.mysensors.org/uploads/files/1454449901412-7.png) Both are working.

I'm still waiting for the PCB. After receiving I want to build the motion sensor.

[bjacobse]

@Tom71
USBtiny is a programmer, and can both burn (upload) sketch + burn bootloader

[sundberg84]

Difference is that if you use a ISP programmer you will use the complete memory. You can use ISP to upload a bootloader which is required to burn a sketch with ftdi into remaining memory but its possible to use a ISP to flash a sketch without bootloader as well.

[bjacobse]

@Matt-Pitts
Depending of your Arduino, the USBtiny is easy to use. Maybe your Aeduino have the pinheader so then only click the cable and burn bootloader. I use Arduino Pro Mini and have an adapter ZIF socket that fits my Arduino ProMini
https://learn.adafruit.com/usbtinyisp

[Tom71]

@bjacobse I'm out of fucus. What was the problem? Can you burn the bootloader+sketch with an USBtiny on an bare Atmgea328p? Connected on MISO/MOSI/SCK/RESET/VCC/GND?
The Arduino Pro Mini is different from the Atmgea328p. On the arduino is an external clock.

[bjacobse]

@Tom71
Can you burn the bootloader+sketch with an USBtiny on an bare Atmgea328p?
I have no idea - I have never tried this.
My originally point is that I have had similar problem to upload a sketch with a FTDI on an Arduino Pro Mini that have been flashed with Optiboot, and when flashed with a "normal" bootloader I could easily upload a sketch with FTDI. I mainly use Arduino Pro Mini 3,3V 8MHz...and that have the crystals etc in place