Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Apex-Ademco-Honeywell D6100 Alarm interface

lafleur last edited by lafleur
This is a MySensor program to control, interface with an APEX Destiny 6100(AN) Alarm panel. This is an older alarm panel, but its capability exceed what can be found on current Honeywell-Ademco panels.

Apex was bought by Ademco who was bought by Honeywell. Its is NOT compatible with current Honeywell-Ademco panels, but has the framework to be adapted.

My system has 63 active zones, most are using wireless Ademco-5800 series sensors

It read's and parses serial data from the alarm and format them into MySensor messages.

This is running on a MoteinoMEGA, and connect to the D6100 via a TTL serial interface
Radio is 915MHz RFM69HW
Tested with MySensor 2.0.0 beta
Tested with D6100 firmware 8.07
```
https://github.com/trlafleur/Sensor_D6100
```
Reply Quote 2
1 Reply Last reply

1
Posts

1071
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
HVAC Controller
My Project • • Michael Link

3

1
Votes

3
Posts

28
Views

We are of like minds, Don't like the cloud based controls (that's another discussion). In my case I have a Bryant/Connex system, heat pump, variable speed fan and 4 zones. There's a lot going on: the 4 zones creates 16 profiles. The fan speed for a profile will depend on the indoor and outdoor temperature. The thermal fluid pump also has to be controlled. A profile will have an optimal air pressure, so there's a sensor there. The controller works just fine not being connected to the cloud. But I want to set the parameters remotely, Bryant/Connex can do this. I also wnat the status of the various actuators and sensors to show up in Home Assistant. The signals sent over the RS422 are proprietary. My plan was to reverse-engineer the signals. After doing this I'll have to experiment to get the right mix of air pressue, fan speed and thermal fluid flow for each profile. I'd like to do the same for my AO Smith heat pump water heater. I'd like to follow your progress. OSD
Halloween Lights
My Project • led strip light ws2812b • • KevinT

1

3
Votes

1
Posts

24
Views

No one has replied
Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

90

7
Votes

90
Posts

73900
Views

Hello everyone, Firstly, I apologize for reviving such an old thread, but I find myself in a unique situation and was hoping some of you might be able to help. I hope everyone's doing well. I have a specific inquiry that I couldn't find a recent solution for. Does anyone here know of a tool to generate "fake" Dooya remote (DC90) RF codes for curtains? I've acquired a few motors without controllers and am trying to integrate them with Home Assistant and Bradlink RF remote. Specifically, I'm searching for a way to generate codes for the Up, Down, Stop, and the "Set" button functions to configure curtain limits. Any insights or guidance would be immensely appreciated. Thank you so much in advance!
Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

2

2
Votes

2
Posts

35
Views

@Kokosnoot good solution. I remember the discussion in the early days of MySensors. I've powered the radio's for most of my sensors from the 3.3v regulator on the arduino board and for me that works perfect. But for my latest designs I decided to add a separate ams regulator for my radio's like the guys suggested in the beginning. Because you basically want the on board regulator to power the mcu only.
Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

5

3
Votes

5
Posts

15
Views

@OldSurferDude thank you !

Apex-Ademco-Honeywell D6100 Alarm interface

Suggested Topics

Welcome
Announcements • • hek

HVAC Controller
My Project • • Michael Link

Halloween Lights
My Project • led strip light ws2812b • • KevinT

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

7
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Apex-Ademco-Honeywell D6100 Alarm interface

Suggested Topics

Welcome Announcements • • hek

HVAC Controller My Project • • Michael Link

Halloween Lights My Project • led strip light ws2812b • • KevinT

Controlling Blinds.com RF Dooya Motors with Arduino and Vera My Project • • petewill

Powering ESP8266 / NRF24L01 repeater through USB (improvement) My Project • • Kokosnoot

Water Filtering and Sterilization and Hot Water Recirculation My Project • • fsgraz

7Online

11.4kUsers

11.1kTopics

112.7kPosts

Welcome
Announcements • • hek

HVAC Controller
My Project • • Michael Link

Halloween Lights
My Project • led strip light ws2812b • • KevinT

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

7
Online

11.4k
Users

11.1k
Topics

112.7k
Posts