Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

How to solder FTDI Platinum so out voltage is 3.3

keldandorin 19 Mar 2016, 19:17 last edited by

Made a mistake and order this FTDI
http://www.aliexpress.com/item/FTDI-Platinum-V2-1-FTDI-Basic-Breakout-5V-3-3V/847242235.html
Been trying to figure out how to solder it to deliver 3.3v and not 5. Anyone know how to do it?

Thx
//Håkan
Reply Quote 0
1 Reply Last reply
Loading More Posts
3
Posts

1.1k
Views
Reply

Reply as topic
Log in to reply
tbowmo Admin 19 Mar 2016, 19:34 last edited by

@keldandorin

move the 0 ohm resistor to 3v3 position, instead of 5v (it's the resistor between the white area, and the bigger yellow capacitor on the board)
Reply Quote 1
1 Reply Last reply 20 Mar 2016, 21:08
keldandorin 20 Mar 2016, 21:08 last edited by @tbowmo

@tbowmo Thx, not easy
Reply Quote 0
1 Reply Last reply

3
Posts

1.1k
Views

Log in to reply

3 out of 3

Suggested Topics

Over the air updates
General Discussion • 23 Mar 2014, 21:38 • ToSa 1 Mar 2015, 11:21

87

1
Votes

87
Posts

50.4k
Views

1 Mar 2015, 11:21

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
hlk-pm01 are to noisy for rfm69?
Hardware • 5 Aug 2023, 21:16 • Tmaster 9 Aug 2023, 16:28

5

0
Votes

5
Posts

27
Views

9 Aug 2023, 16:28

@Tmaster Never assume the original PCB was just a circuit of components, the PCB can incorporate RF shields and antenna radio ground planes...
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • 6 Jan 2024, 19:39 • OldSurferDude 11 Jan 2024, 04:39

2

0
Votes

2
Posts

21
Views

11 Jan 2024, 04:39

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }
Best time of year to buy higher quality small project solar panels?
Hardware • 10 Jun 2021, 19:19 • NeverDie 30 Aug 2024, 14:01

5

1
Votes

5
Posts

71
Views

30 Aug 2024, 14:01

It probably has to do with fewer people buying them once summer ends, so companies might lower prices to clear out stock before winter.
Best VOC sensor for detecting a wide range of VOC's?
Hardware • 26 Oct 2023, 23:59 • NeverDie 18 Nov 2023, 01:41

3

1
Votes

3
Posts

36
Views

18 Nov 2023, 01:41

@eiten I haven't yet made any progress on finding a good VOC sensor, but along the way I did find out something interesting regarding CO2: namely, if you sleep with your bedroom door closed at night, then the odds are good that the CO2 levels rise to surprisingly high and unhealthy levels. The better CO2 sensors are factory calibrated and never again need recalibration for the life of the sensor (usually around 10 years or so), because they are used in HVAC systems to control fresh air intake to guarantee indoor air quality. As a for instance, here is one such CO2 sensor: https://www.digikey.com/en/products/detail/senseair/006-0-0008/15790694 At around $50 for just the sensor element itself, it's not exactly cheap, but then again, I'd say it's worth it, because who wants to be burdened by remembering to calibrate their CO2 sensors? Ideally, I'd like to find a sensitive VOC sensor that also will never require calibration. Nearly all, and maybe all, of the off-the-shelf IAQ montoring stuff that you might buy for, say, $300 or less seems to require periodic calibration. For that reason, this might be one of those occasions where build is rather than buy.
Sensors and more
Hardware • 19 Jun 2023, 00:41 • Robert Leverett 19 Jun 2023, 00:41

1

0
Votes

1
Posts

16
Views

No one has replied

0
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1