Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Mys Interposer NRF/Arduino Pro Mini

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/56/Mys-Interposer-NRFArduino-Pro-Mini
Reply Quote 2
1 Reply Last reply
Mountek Angel last edited by

Hi, any plans to sell this design on PCBways?
Reply Quote 0
1 Reply Last reply
terxw last edited by

I would like to see panelized version for dirtypcb, someone?
Reply Quote 0
1 Reply Last reply
enlo last edited by

I ordered a batch from PCBs.io
With the permission of the orginal author, I could enable sharing it there, which should reduce the price...
Reply Quote 0
1 Reply Last reply

mysensors 189 temperature 58 contest2016 19 ds18b20 15 binary switches 3

4
Posts

2272
Views

Log in to reply

Suggested Topics

💬 Teleinfo with parasitic power
OpenHardware.io • mysensors rfm69hw teleinfo • • openhardware.io

2

0
Votes

2
Posts

1546
Views

I'm very interested by your setup. It has been a shame to have some low voltage power in order to measure power consumption I hope you can display something soon. Regards, Qq.
Ultimate MySensors invisible project housing
OpenHardware.io • mysensors project box • • openhardware.io

4

2
Votes

4
Posts

1863
Views

Nice!!! This im making!
💬 OH 433Mhz Mysensors Bridge
OpenHardware.io • mysensors contest2017 433mhz • • openhardware.io

4

0
Votes

4
Posts

2060
Views

Wow, great! Its alway nice to see others using my work too. Your code improvement seem to be very helpful too. I have most recently also integrated this directly into my gateway build (see here). I am still struggling with code there though.
💬 NModule MiLight bridge shield
OpenHardware.io • mysensors contest2017 nmodule milight • • openhardware.io

3

0
Votes

3
Posts

1374
Views

Hello @reinhold, yes the PCB works, I have assembled one and tested it for basic function (not all buttons and leds) but I have stability problem that comes from the software, I put it aside to do other things and didn't have time to go back to it, if there is some interest for it I will find some time and finish at least a basic script.
💬 Ikea Molgan Hack
OpenHardware.io • mysensors motion pir hack ikea molgan • • openhardware.io

90

5
Votes

90
Posts

27412
Views

@yveaux said in Ikea Molgan Hack: @magpern the instructions on openhardware.io state that the Molgan must be battery powered while programming: Well, then I can confirm that you don't have to power the Molgan from batteries just for programming. Burning the bootloader works fine with just power from the ISP port and programming it through FTDI works fine if power comes from the FTDI. What I found wierd is that the atmega328 had power, the radio had power, it wrote debug messages to the FTDI - when powered through the FTDI, it send radio messages etc, but it just did not receive messages. Messages where not received until I supplied power to the + / - pads (battery pads). I did read the instructions on openhardware.io, but I didn't follow then to the t.
MyPowerMeter v1.0
OpenHardware.io • mysensors contest2016 energy monitor • • openhardware.io

6

2
Votes

6
Posts

5355
Views

great job
Convert DS18B20 temperature to string
Hardware • ds18b20 • • Maki Young

2

0
Votes

2
Posts

1214
Views

Accound banned for spam. Promotes a vendor and has copied a question from https://electronics.stackexchange.com/questions/33103/convert-ds18b20-temperature-to-string
Ultrasonic sensor JSN-SR04T
Hardware • mysensors • • Kavitha

4

0
Votes

4
Posts

46
Views

To provide a large enough pulse to drive the ceramic transducer , you need a lot of energy, so they pump up the 5v with an inductor/transformer to provide a high voltage pulse. This is 60v or more… The more Energy you produce the farther the pulse will travel…. Everything thing else on the board run at 3.3 to 5V. Add a large Capacitor of 100 µF are so between the 5v and ground on the device, this may clean up your problem.. Some CPU modules just can’t supply enough current quick enough that’s needed when the pulse is triggered. These are very inexpensive device, we’re luck to see them work at 1/2 the spec range.

1
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1