Powering a sensor with digital out

[mfalkvidd]

You could try changing

const int VAL_PROBE = 0; // initializing the moisture variable

to

#define VAL_PROBE A0

I don't see any point in declaring it const int, and I prefer to use the An naming to make it clear which pin I am using.

[hozze]

@TheoL , Thanks for the suggestion . Tried that, same result.

@mfalkvidd , Thanks for the code suggestion, I made the change. Regarding the issue, I did check with a multi-meter and it shows 0V . To make sure I also used the example blink sketch with pin 2 as output and it is showing 3.24V I will attach the wiring diagram(I haven't drawn one). Things I noticed.

• On commenting the Mysensor.h library and related code from above sketch I'm able to turn on the Pin
• I tried using different digital pins and same result.
• To make sure I measured the output pin voltage powering it with USB ( without connecting the board to radio and soil sensor ) , same result voltage is 0V

[mfalkvidd]

@hozze looks like good troubleshooting, great work.

Very interesting that it works when uncommenting the MySensors stuff. I think there are some leds blinking features in 2.0 (have not yet moved to 2.0 myself so I don't know more than what I've read in the forum), but I think that is only enabled for gateways.

Does it help if you remove include <SPI.h>? It looks like SPI is not used so it shouldn't make a difference but you might as well remove it if you aren't using it.

[Yveaux]

@mfalkvidd said:

there are some leds blinking features in 2.0

This feature is also present in previous versions and not limited to gateways.
Pin 2 however is never used for leds as it is the default irq pin for nRF.
Try with another pin, e.g. 4/5/6 and see if that makes a difference.

[hozze]

@mfalkvidd : Removed SPI.h , it didn't help though. Thanks for pointers on cleaning up the code :smiley:
@Yveaux :
Tried with pin 5 , same result.
Tried using a different pro mini ( Atmega328 16Mhz 5 v ) got same result , no output on pin :expressionless:

[Yveaux]

@hozze make sure you don't define MY_LEDS_BLINKING_FEATURE or MY_INCLUSION_MODE_FEATURE, as their pin mappings might interfere with your application.

[hozze]

@Yveaux I don't have those defined. Below is my current code.

#define MY_NODE_ID 1  // node id 
#define MY_RADIO_NRF24  // enabling support for NRF radio module
#define NODE_ID 1  // sensor id
#define SENS_ON 5
#define VAL_PROBE A0
#include <MySensors.h>

MyMessage msg(NODE_ID, V_LEVEL); // constructing the msg

void setup()
{
  pinMode(SENS_ON, OUTPUT);
}

void presentation()
{
  present(NODE_ID, S_MOISTURE);  // presenting the sensor 
  sendSketchInfo("SoilSensor", "0.1"); //meta data 
}

void loop()
{
  digitalWrite(SENS_ON, HIGH);
  delay(1000); // To check the input voltage of pin 2
  int moisture = analogRead(VAL_PROBE); //measuring the moisture
  send(msg.set(moisture));  // sending the data 
  digitalWrite(SENS_ON, LOW); // turn it off
//  sleep(1000);  // sleeping for 10 sec
}

An as soon as I comment it out like below the pin out on 5 works

#define MY_NODE_ID 1  // node id 
#define MY_RADIO_NRF24  // enabling support for NRF radio module
#define NODE_ID 1  // sensor id
#define SENS_ON 5
#define VAL_PROBE A0
//#include <MySensors.h>

MyMessage msg(NODE_ID, V_LEVEL); // constructing the msg

void setup()
{
  pinMode(SENS_ON, OUTPUT);
}

void presentation()
{
//  present(NODE_ID, S_MOISTURE);  // presenting the sensor 
//  sendSketchInfo("SoilSensor", "0.1"); //meta data 
}

void loop()
{
  digitalWrite(SENS_ON, HIGH);
  delay(1000); // To check the input voltage of pin 2
  int moisture = analogRead(VAL_PROBE); //measuring the moisture  
// send(msg.set(moisture));  // sending the data 
  digitalWrite(SENS_ON, LOW); // turn it off
//  sleep(1000);  // sleeping for 10 sec
}

[Yveaux]

@hozze it's strange that you only measure 3.24V on the output pin if you're using a 5V pro mini. This is IMHO an indication that something is wrong, also when your pin does seem to toggle.

[hozze]

I see that output on pro mini Atmega168 3.3v with commented sketch.
I tried with a different 5v pro mini Atmega368 and I'm getting 5.04V on output pin with commented sketch.

[TheoL]

@Yveaux @hozze Are you sure it's a ProMini 5V? Could you measure the voltage on the Raw pin.

I've received some Pro Mini 3.3V while I actually did order 5V.

It's just a guess.

[hozze]

@TheoL I have two pro mini's. I measured the voltage across a output pin ( HIGH ) and GND and it gives me near 5V on one and near 3.3V on another .So it looks as if I do have 5V pro mini.

I have tried few other sketches on both, seems they are working fine, I face the specific issue only when including the Mysensor.h library. I will give it a try on a nano that I have and see what happens.

[TheoL]

@hozze It was just a guess. I once compiled a sketch for a 5V and uploaded it to a ProMini 3.3V. Took me a while before I noticed my mistake. I just didn;t understand why my Arduino couldn't control my relay boards ;-)

[hozze]

@TheoL :smiley: me too learning things the hard way.

Thanks for all the pointers that you guys are giving . Looks as if I'm in the right place and with a great community,

Let me tinker a bit more and see if I can get somewhere, if anyone can give any further info kindly do.

[Boots33]

@hozze You should enable debugging at the top of your sketch with

// Enable debug prints to serial monitor
#define MY_DEBUG

and check the serial monitor to see if the radio is initialising . Maybe the loop part of the program will not run if this does not happen. That could be why commenting out the #include <MySensors.h> allows it to work.

You might also use wait instead of delay

[hozze]

@Boots33 , I enabled MY_DEBUG. Sorry if I sound stupid. I have connected the pro mini to computer with USB serial CP2102 for programming/serial debug , at the same time can I power the pro mini + Radio with an external power supply 3.3V ?

I did something similar with a ATTINY85 few days back and bricked it :cry: ( Connected it to USB and same time powered it )

[mfalkvidd]

@hozze connect gnd from the serial adapter AND the external power supply to gnd on the Arduino. Connect + on the external adapter to the pin you normally use (vcc or raw). Do not connect + from the serial adapter. That's it.

[Boots33]

@hozze The whole purpose of a good forum is for people to share ideas and knowledge. So never be worried about asking questions. :)

[hozze]

Thanks guys, I will check this out.

[hozze]

Was away from arduino for over a week with regular job. Tested the code with debug on a new arduino pro mini 3.3v 8Mhz and the below is the output ( please note that the values getting send are random values , i'm still not able to power the sensor with digital Pin )

TSP:MSG:SEND 1-1-0-0 s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=ok:0100
TSP:MSG:SEND 1-1-0-0 s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=ok:2.0.0
TSP:MSG:SEND 1-1-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=ok:0
TSP:MSG:READ 0-0-1 s=255,c=3,t=15,pt=6,l=2,sg=0:0100
TSP:MSG:SEND 1-1-0-0 s=1,c=0,t=35,pt=0,l=0,sg=0,ft=0,st=ok:
TSP:MSG:SEND 1-1-0-0 s=255,c=3,t=11,pt=0,l=10,sg=0,ft=0,st=ok:SoilSensor
TSP:MSG:SEND 1-1-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=ok:0.1
Request registration...
TSP:MSG:SEND 1-1-0-0 s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=ok:2
TSP:MSG:READ 0-0-1 s=255,c=3,t=27,pt=1,l=1,sg=0:1
Node registration=1
Init complete, id=1, parent=0, distance=1, registration=1
TSP:MSG:SEND 1-1-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:786
TSP:MSG:SEND 1-1-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:503
TSP:MSG:SEND 1-1-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:410
TSP:MSG:SEND 1-1-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:425
TSP:MSG:SEND 1-1-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:461
TSP:MSG:SEND 1-1-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:539
TSP:MSG:SEND 1-1-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:507
TSP:MSG:SEND 1-1-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:392

Looks fine for me , still I can't turn a digital pin On :disappointed:

[Boots33]

@hozze It really should be working. I tried your original above and with a led connected to pin 5 it turns on when the code is run

try the code below with some serial prints to see what happens

// Enable debug prints to serial monitor
#define MY_DEBUG
#define MY_NODE_ID 150  // node id 
#define MY_RADIO_NRF24  // enabling support for NRF radio module

#define NODE_ID 1  // sensor id
#define SENS_ON 5
#define VAL_PROBE A0
#include <MySensors.h>
#define POWER_ON 1  //  value to write to turn on sensor
#define POWER_OFF 0 //  value to write to turn off sensor
MyMessage msg(NODE_ID, V_LEVEL); // constructing the msg

void setup()
{
  pinMode(SENS_ON, OUTPUT);
}

void presentation()
{
  present(NODE_ID, S_MOISTURE);  // presenting the sensor
  sendSketchInfo("SoilSensor", "0.1"); //meta data
}

void loop()
{


  digitalWrite(SENS_ON, POWER_ON);
  Serial.print("Sensor Power on pin "); Serial.print(SENS_ON); Serial.print(" is..."); Serial.println((POWER_ON));
  wait(1000); // To check the input voltage of pin 2
  int moisture = analogRead(VAL_PROBE); //measuring the moisture
  send(msg.set(moisture));  // sending the data
  digitalWrite(SENS_ON, POWER_OFF); // turn it off
  Serial.print("Sensor Power on pin "); Serial.print(SENS_ON); Serial.print(" is..."); Serial.println((POWER_OFF));

  wait(1000);
}

I get an output like this below and the led flashes on and off at 1 second intervals. Maybe try just a led with a 200 to 300 ohm resistor on pin 5 to see what is happening. could the moisture sensor be drawing more than the arduino can give?

TSP:MSG:SEND 150-150-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,ft=1,st=ok:0
TSP:MSG:READ 0-0-150 s=255,c=3,t=6,pt=0,l=1,sg=0:M
TSP:MSG:SEND 150-150-0-0 s=1,c=0,t=35,pt=0,l=0,sg=0,ft=0,st=ok:
TSP:MSG:SEND 150-150-0-0 s=255,c=3,t=11,pt=0,l=10,sg=0,ft=0,st=ok:SoilSensor
TSP:MSG:SEND 150-150-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=ok:0.1
Request registration...
TSP:MSG:SEND 150-150-0-0 s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=ok:2
TSP:MSG:READ 0-0-150 s=255,c=3,t=27,pt=1,l=1,sg=0:1
Node registration=1
Init complete, id=150, parent=0, distance=1, registration=1
Sensor Power on pin 5 is...1
TSP:MSG:SEND 150-150-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:511
Sensor Power on pin 5 is...0
Sensor Power on pin 5 is...1
TSP:MSG:SEND 150-150-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:313
Sensor Power on pin 5 is...0
Sensor Power on pin 5 is...1
TSP:MSG:SEND 150-150-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:254
Sensor Power on pin 5 is...0
Sensor Power on pin 5 is...1
TSP:MSG:SEND 150-150-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:326
Sensor Power on pin 5 is...0
Sensor Power on pin 5 is...1
TSP:MSG:SEND 150-150-0-0 s=1,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=ok:235
Sensor Power on pin 5 is...0
Sensor Power on pin 5 is...1