Sending sensor data from raspberry via NRF24L01+ to arduino

[mfalkvidd]

@LaMB95 You might want to start reading the getting started guide, https://www.mysensors.org/about

[LaMB95]

I have been working on the installation of the libraries.
I have Added them to the Arduino ide software but when I run the gateway serial code it shows that
fatal error: MySensors.h: No such file or directory
compilation terminated.

What is causing this?
PS I am using a Macbook

[mfalkvidd]

@LaMB95 seems like the MySensors library isn't installed. Did you follow the instructions on https://www.mysensors.org/about/arduino#installing-the-sensor-libraries ? If so, did you get any error messages?

[gohan]

I'm doing a project very similar to yours. Mysensors library can be installed from library manager in arduino ide, just like many other libraries.

[LaMB95]

@mfalkvidd @gohan

Just resolved the issue !

Apparently my Arduino Ide wasnt updated to the lastest version which explains why I never found the Library Manager :P

[mfalkvidd]

Great that you found the problem @LaMB95, thanks for reporting back. It might help someone else in the future if they have the same problem :)

[LaMB95]

@mfalkvidd
Thanks !
However I am still facing some issues trying to set up a gateway with the raspberry pi,

Do you know who could help me with that ?

[mfalkvidd]

@LaMB95 just create a new thread describing what you have done, what result you got and what result you expected and we'll help.

[hugo_pn]

Hi,

I'm having problems exactly the same as @LaMB95

The MySensors library is installed, at least is says so doing as shown in the link @mfalkvidd sent.

This is my error:

"
DallasTemperatureSensor.ino:36:25: fatal error: MySensors.h: No such file or directory
Compilation terminated.
"

Thanks

[LaMB95]

@hugo_pn

Okay could you check what version of Arduino IDE you have now ?
If there is a newer version upgrade to that.

My issue was that I could not find the library manager in the version I had.

Hope it helps !

[gohan]

@hugo_pn

You don't have the mysensors library installed

[hugo_pn]

Hi all,

@LaMB95
I'll have to get back to you later on that.

@gohan
The software says it's installed. Is there a way to uninstall and install again?

Thanks

[gohan]

@hugo_pn
from library manager you can install, remove, update the libraries. You can try to remove from the Arduino IDE and try to copy the library manually where you have all the libraries

[hugo_pn]

Hi all,

Sorry for the delay, my IDE is 1.6.5 going to try and update.

Thanks in advance.

cheers

[hugo_pn]

Got it working, IDE updated and everything working.

My temperature already getting values.

Going to try and attached another DS18B20 as shown in the example.

Don´t really know what is going to show up.

Thanks

[gohan]

Just change the node ID and you shouldn't have any problem

[LaMB95]

@gohan

I am facing an issue while sending data from an Arduino pro mini 5V to an arduino UNO. Receiving a lot of garbage from the Pro mini.
Any idea why ?

[gohan]

@LaMB95
do you have a log to take a look? Just to understand what is the garbage you are talking about.
What NRF24 library are you using? I'm using the one from Maniacbug

[LaMB95]

@gohan
Code in Pro Mini:

#include <HardwareSerial.h>
#include <SPI.h>
#include <nRF24L01.h>
#include <RF24.h>

RF24 radio(9, 10);

const byte rxAddr[6] = "00001";

void setup()
{
  while (!Serial);
  Serial.begin(9600);
  
  radio.begin();
  radio.openReadingPipe(1, rxAddr);
  
  radio.startListening();
}

void loop()
{
  if (radio.available())
  {
    char text[32] = {0};
    radio.read(&text, sizeof(text));
    
    Serial.println(text);
  }
}

Code in Uno:

#include <SPI.h>
#include <nRF24L01.h>
#include <RF24.h>

RF24 radio(9, 10);

const byte rxAddr[6] = "00001";

void setup(void)
{
  radio.begin();
  //Serial.println(F("*** PRESS 'T' to begin transmitting to the other node"));
  radio.setRetries(15, 15);
  radio.openWritingPipe(rxAddr);
  
  radio.stopListening();
}

void loop(void)
{
  const char text[] = "Hello World";
  radio.write(&text, sizeof(text));
  
  delay(1500);
}

I have set the processor to 3.3V 8MHz.
I have connected the Pro mini to the computer via a CP2102 breakout board.

[gohan]

I haven't tried the Mini yet, I am waiting for it to be delivered so I can't help you much, but my best shot could be something with serial speed somewhere or something related.
Have you tried to use a 16x2 LCD to show data instead of the serial console? I do it sometimes when I don't want to take bring computer with me if I only need to show a few values.