Domoticz(Raspberry) with Mysensor USB gateway without Radio

[Dumoulin]

Hello,

I try to create USB gateway without radio, but my domoticz under raspberry don't see this gateway.

Could you check my code?
Thanks

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level.
//#define MY_RF24_PA_LEVEL RF24_PA_LOW

// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE

// Inverses behavior of inclusion button (if using external pullup)
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP

// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE

// Flash leds on rx/tx/err
// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED

#include <MySensors.h>
#include <SPI.h>

#define CHILD_ID 1   // Id of the sensor child

#define IN_Sejour_Presence1  2  // Arduino Digital I/O pin number for Presence
#define IN_Sejour_Presence2  3  // Arduino Digital I/O pin number for Presence
#define IN_Sejour_Presence3  4  // Arduino Digital I/O pin number for Presence
#define IN_ChParents_Presence  5  // Arduino Digital I/O pin number for Presence

#define NUMBER_OF_INPUT 4 // Total number of attached input port

#define RELAY_Sejour_Volet1_Bas  22  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Volet1_Stop  23  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Volet1_Haut  24  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Volet2_Bas  25  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Volet2_Stop  26  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Volet2_Haut  27  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Volet3_Bas  28  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Volet3_Stop  29  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Volet3_Haut  30  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Lumiere1  31  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Lumiere2  32  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Lumiere3  33  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Chauffage1  34  // Arduino Digital I/O pin number for relay
#define RELAY_Sejour_Chauffage2  35  // Arduino Digital I/O pin number for relay

#define RELAY_SdJ_Volet1_Bas  37  // Arduino Digital I/O pin number for relay
#define RELAY_SdJ_Volet1_Stop  38  // Arduino Digital I/O pin number for relay
#define RELAY_SdJ_Volet1_Haut  39  // Arduino Digital I/O pin number for relay

#define RELAY_ChParents_Volet_Bas  41  // Arduino Digital I/O pin number for relay
#define RELAY_ChParents_Volet_Stop  42  // Arduino Digital I/O pin number for relay
#define RELAY_ChParents_Volet_Haut  43  // Arduino Digital I/O pin number for relay
#define RELAY_ChParents_Lumiere  44  // Arduino Digital I/O pin number for relay
#define RELAY_ChParents_Chauffage  45  // Arduino Digital I/O pin number for relay

#define NUMBER_OF_RELAYS 32 // Total number of attached relays port 22 to 53
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay

unsigned long Duree_Sejour_Lum1 = 60000;
unsigned long Duree_Sejour_Lum2 = 60000;
unsigned long Duree_Sejour_Lum3 = 60000;
unsigned long Duree_ChParents_Lum = 60000;

unsigned long SLEEP_TIME = 120000; // Sleep time between reports (in milliseconds)

bool IN_Sejour_Presence1_Etat = LOW;
bool IN_Sejour_Presence1_Etat_Avant = LOW;
bool IN_Sejour_Presence2_Etat = LOW;
bool IN_Sejour_Presence2_Etat_Avant = LOW;
bool IN_Sejour_Presence3_Etat = LOW;
bool IN_Sejour_Presence3_Etat_Avant = LOW;
bool IN_ChParents_Presence_Etat = LOW;
bool IN_ChParents_Presence_Etat_Avant = LOW;

// Initialize motion message
MyMessage msg(CHILD_ID, V_TRIPPED);

void before()
{
   // Send the sketch version information to the gateway and Controller
   // sendSketchInfo("MySensorBas", "1.0");
   
    for (int sensor=RELAY_Sejour_Volet1_Bas, pin=RELAY_Sejour_Volet1_Bas; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
        // Then set relay pins in output mode
        pinMode(pin, OUTPUT);
        // Set relay to last known state (using eeprom storage)
        digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
    }
     pinMode(IN_Sejour_Presence1, INPUT);
     pinMode(IN_Sejour_Presence2, INPUT);
     pinMode(IN_Sejour_Presence3, INPUT);
     pinMode(IN_ChParents_Presence, INPUT);
}

void setup()
{

}

void presentation()
{
    // Send the sketch version information to the gateway and Controller
    sendSketchInfo("Salon_Parents_SdJ", "1.0");

    for (int sensor=RELAY_Sejour_Volet1_Bas, pin=RELAY_Sejour_Volet1_Bas; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
        // Register all sensors to gw (they will be created as child devices)
        present(sensor, S_BINARY);
    }

     for (int sensor=IN_Sejour_Presence1, pin=IN_Sejour_Presence1; sensor<=NUMBER_OF_INPUT; sensor++, pin++) {
        // Register all sensors to gw (they will be created as child devices)
        present(sensor, S_MOTION);
    }
}

void loop()
{
    // Read digital motion value
    IN_Sejour_Presence1_Etat = digitalRead(IN_Sejour_Presence1);
    if (IN_Sejour_Presence1_Etat != IN_Sejour_Presence1_Etat_Avant){
      if (IN_Sejour_Presence1_Etat == HIGH){
  //          Serial.println(IN_Sejour_Presence1_Etat);
            send(msg.set(IN_Sejour_Presence1_Etat?"1":"0"));  // Send tripped value to gw
      }
      IN_Sejour_Presence1_Etat_Avant = IN_Sejour_Presence1_Etat;
    }
 
    // Read digital motion value
    IN_Sejour_Presence2_Etat = digitalRead(IN_Sejour_Presence2);
    if (IN_Sejour_Presence2_Etat != IN_Sejour_Presence2_Etat_Avant){
      if (IN_Sejour_Presence2_Etat == HIGH){
  //          Serial.println(IN_Sejour_Presence2_Etat);
            send(msg.set(IN_Sejour_Presence2_Etat?"1":"0"));  // Send tripped value to gw
      }
      IN_Sejour_Presence2_Etat_Avant = IN_Sejour_Presence2_Etat;
    }

    // Read digital motion value
    IN_Sejour_Presence3_Etat = digitalRead(IN_Sejour_Presence3);
    if (IN_Sejour_Presence3_Etat != IN_Sejour_Presence3_Etat_Avant){
      if (IN_Sejour_Presence3_Etat == HIGH){
  //          Serial.println(IN_Sejour_Presence3_Etat);
            send(msg.set(IN_Sejour_Presence3_Etat?"1":"0"));  // Send tripped value to gw
      }
      IN_Sejour_Presence3_Etat_Avant = IN_Sejour_Presence3_Etat;
    }

    // Read digital motion value
    IN_ChParents_Presence_Etat = digitalRead(IN_ChParents_Presence);
    if (IN_ChParents_Presence_Etat != IN_ChParents_Presence_Etat_Avant){
      if (IN_ChParents_Presence_Etat == HIGH){
  //          Serial.println(IN_ChParents_Presence_Etat);
            send(msg.set(IN_ChParents_Presence_Etat?"1":"0"));  // Send tripped value to gw
      }
      IN_ChParents_Presence_Etat_Avant = IN_ChParents_Presence_Etat;
    }
}

void receive(const MyMessage &message)
{
    // We only expect one type of message from controller. But we better check anyway.
    if (message.type==V_STATUS) {
        // Change relay state
        digitalWrite(message.sensor-1+RELAY_Sejour_Volet1_Bas, message.getBool()?RELAY_ON:RELAY_OFF);
        // Store state in eeprom
        saveState(message.sensor, message.getBool());
        // Write some debug info
   //     Serial.print("Incoming change for sensor:");
   //     Serial.print(message.sensor);
   //     Serial.print(", New status: ");
   //     Serial.println(message.getBool());
    }
}

[gohan]

Have you tried commenting mydebug?

[Dumoulin]

Yes, I Have:
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;MCO:BGN:BFR
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;!TSM:INIT:TSP FAIL
0;255;3;0;9;TSM:FAIL:CNT=1
0;255;3;0;9;TSM:FAIL:PDT.

But I don't know why I have on first error :Transport device initialization failed

[Dumoulin]

When I put serial gateway code availiable on MySensor Site, I have the same error.

0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;!TSM:INIT:TSP FAIL
0;255;3;0;9;TSM:FAIL:CNT=1
0;255;3;0;9;TSM:FAIL:PDT

I try to do MySensor USB gateway without radio for physical IO on Arduino(to have relay)

[gohan]

It's actually weird, but if only need relays, you can control gpio directly from domoticz.

[Dumoulin]

Ok, I find.

Sketchinfo was in Presntation, and should be in setup.

void setup()
{
    // Send the sketch version information to the gateway and Controller
    sendSketchInfo("Salon_Parents_SdJ", "1.0");

    for (int sensor=RELAY_Sejour_Volet1_Bas, pin=RELAY_Sejour_Volet1_Bas; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
        // Register all sensors to gw (they will be created as child devices)
        present(sensor, S_BINARY);
    }

     for (int sensor=IN_Sejour_Presence1, pin=IN_Sejour_Presence1; sensor<=NUMBER_OF_INPUT; sensor++, pin++) {
        // Register all sensors to gw (they will be created as child devices)
        present(sensor, S_MOTION);
    }
}```