Combining relay and temperature sketch

[Mad6969]

Ok, now I have another problem.

When I build the relay/dht node, I first made the thing work with the relay with button actuator sketch alone (the DHT was plugged, but it was an additional feature I wanted to add).

Now, it seems that my power source doesn't have enough power to make the relay to close. The led on my relay board blinks when the relay is on and off, but nothing.

That's weird.. I'll try running the relay sketch alone, just to see.

[gohan]

@Tim76 ok, let's go back to the beginning. Try with one sensors only, if everything works then add one relay, then add the second and keep adding the sensors until you see something wrong. You need to go step by step, otherwise with all that stuff you have it will be impossible to debug.

[Tim76]

@gohan ok

[Tim76]

@gohan both sketches work perfectly stand alone.... but I think the problem lies within the assingment of the child id's...
James Bruce talks about this "bug" in his video on how to combine sketches.....
They relay sketch assigns from 1 to 16
And the temp sketch assigns from 0 to 15
So they both try to use the same id's for their children when you try to combine them....
I need a way to get around that and have relays on 1-16 and temp on 17 to 32......
Or there might just be the same "bug" in the temperature sketch.....😬😬 wich might mean that they can't be combined for now......😒😒

[gohan]

if use something like this in presentation?

for (int i=1; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i+3, S_TEMP);

you get the idea, just shift the child id of the dallas sensors and leave the first 4-5 IDs for relays

[Tim76]

@gohan aha! Will be trying that later tonight..... I'll keep you posted! 😊 Thx man!

[Tim76]

@gohan soooooo...... I tried this:

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Temperature Sensor", "1.1");

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=1; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i+16, S_TEMP);
  }
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);
    // Set relay to last known state (using eeprom storage)
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}

now I get the temp sensors with child id's 1 to 16 and no relays at all

[gohan]

I probably used wrong sintax

[Tim76]

@gohan tried this again...... same result.....

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=17; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);
    // Set relay to last known state (using eeprom storage)
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}

[Tim76]

here's the complete code as she is right now...

// Enable debug prints to serial monitor
#define MY_DEBUG 
#define MY_RF24_CE_PIN 49
#define MY_RF24_CS_PIN 53
// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
#define MY_NODE_ID 30

#include <SPI.h>
#include <MySensors.h>  
#include <DallasTemperature.h>
#include <OneWire.h>



#define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 16
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
bool receivedConfig = false;
bool metric = true;
// Initialize temperature message
MyMessage msgTemp(0,V_TEMP);


#define RELAY_1  30  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 16 // Total number of attached relays
#define RELAY_ON 0  // GPIO value to write to turn on attached relay
#define RELAY_OFF 1 // GPIO value to write to turn off attached relay

void before()
{
  // Startup up the OneWire library
  sensors.begin();
}

void setup()  
{ 
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Greenhouse main controller", "1.0");

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=17; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);
    // Set relay to last known state (using eeprom storage)
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}

void loop()     
{     
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {

    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getControllerConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;

    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif

      // Send in the new temperature
      send(msgTemp.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }
  wait(3000);
  }
  void receive(const MyMessage &message)
{
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type==V_STATUS) {
    // Change relay state
    digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
    // Store state in eeprom
    saveState(message.sensor, message.getBool());
    // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.print(message.sensor);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
  }
}```

[gohan]

@Tim76 you forgot to present the relays.... :sweat:

[Tim76]

@gohan no I didn't...

  // Present all sensors to controller
  for (int i=17; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);
    // Set relay to last known state (using eeprom storage)
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}```

[Tim76]

@gohan seems like it's early for both of us.....;-)

[gohan]

you only have present(i, S_TEMP) but you also need to add present(sensor, S_BINARY) in the relay section otherwise you will not present any relay at all.

[Tim76]

@gohan 😳😳😳 seems like it's only early for one of us...... I,ll change it later today.....

[Tim76]

@gohan so I fixed that....... and now I get this in Domoticz....

0 Unknown! #1. V_TEMP (20.7) true 2017-05-10 11:44:39
1 S_LIGHT/S_BINARY #1. V_TEMP (20.7) true 2017-05-10 11:44:43
2 S_LIGHT/S_BINARY #1. V_TEMP (20.9) true 2017-05-10 11:44:04
3 S_LIGHT/S_BINARY true 2017-05-10 11:34:13
4 S_LIGHT/S_BINARY true 2017-05-10 11:34:14
5 S_LIGHT/S_BINARY true 2017-05-10 11:34:15
6 S_LIGHT/S_BINARY true 2017-05-10 11:34:15
7 S_LIGHT/S_BINARY true 2017-05-10 11:34:16
8 S_LIGHT/S_BINARY true 2017-05-10 11:34:17
9 S_LIGHT/S_BINARY true 2017-05-10 11:34:17
10 S_LIGHT/S_BINARY true 2017-05-10 11:34:18
11 S_LIGHT/S_BINARY true 2017-05-10 11:34:18
12 S_LIGHT/S_BINARY true 2017-05-10 11:34:19
13 S_LIGHT/S_BINARY true 2017-05-10 11:34:19
14 S_LIGHT/S_BINARY true 2017-05-10 11:34:20
15 S_LIGHT/S_BINARY true 2017-05-10 11:34:20
16 S_LIGHT/S_BINARY true 2017-05-10 11:34:21
17 S_TEMP true 2017-05-10 11:34:12
18 S_TEMP true 2017-05-10 11:34:12
255 S_ARDUINO_NODE 2.1.1 false 2017-05-10 11:34:12

so it seems I do get temp Id's from 17 to 32, but the values stay in 0,1,2 where the relays 1 and 2 don't work.....

[gohan]

There must be a bug in the relay section, I can't check it today, I'm out all day.
Try to add some debug serial print to see what values are being exchanged

[Tim76]

@gohan output of the serial port

0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 MCO:BGN:BFR
144 TSM:INIT
145 TSF:WUR:MS=0
153 TSM:INIT:TSP OK
154 TSM:INIT:STATID=51
157 TSF:SID:OK,ID=51
158 TSM:FPAR
195 TSF:MSG:SEND,51-51-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
986 TSF:MSG:READ,0-0-51,s=255,c=3,t=8,pt=1,l=1,sg=0:0
990 TSF:MSG:FPAR OK,ID=0,D=1
2202 TSM:FPAR:OK
2203 TSM:ID
2204 TSM:ID:OK
2206 TSM:UPL
2211 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2232 TSF:MSG:READ,0-0-51,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2237 TSF:MSG:PONG RECV,HP=1
2240 TSM:UPL:OK
2241 TSM:READY:ID=51,PAR=0,DIS=1
2246 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2284 TSF:MSG:READ,0-0-51,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2291 TSF:MSG:SEND,51-51-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.1.1
2301 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
4329 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=11,pt=0,l=25,sg=0,ft=0,st=OK:Greenhouse main controlle
4340 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
4350 TSF:MSG:SEND,51-51-0-0,s=17,c=0,t=6,pt=0,l=0,sg=0,ft=0,st=OK:
4359 TSF:MSG:SEND,51-51-0-0,s=18,c=0,t=6,pt=0,l=0,sg=0,ft=0,st=OK:
4369 TSF:MSG:SEND,51-51-0-0,s=1,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4376 TSF:MSG:SEND,51-51-0-0,s=2,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4384 TSF:MSG:SEND,51-51-0-0,s=3,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4397 TSF:MSG:SEND,51-51-0-0,s=4,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4407 TSF:MSG:SEND,51-51-0-0,s=5,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4418 TSF:MSG:SEND,51-51-0-0,s=6,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4434 TSF:MSG:SEND,51-51-0-0,s=7,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4449 TSF:MSG:SEND,51-51-0-0,s=8,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4459 TSF:MSG:SEND,51-51-0-0,s=9,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4489 TSF:MSG:SEND,51-51-0-0,s=10,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4505 TSF:MSG:SEND,51-51-0-0,s=11,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4515 TSF:MSG:SEND,51-51-0-0,s=12,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4528 TSF:MSG:SEND,51-51-0-0,s=13,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4540 TSF:MSG:SEND,51-51-0-0,s=14,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4556 TSF:MSG:SEND,51-51-0-0,s=15,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4564 TSF:MSG:SEND,51-51-0-0,s=16,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4571 MCO:REG:REQ
4576 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
4583 TSF:MSG:READ,0-0-51,s=255,c=3,t=27,pt=1,l=1,sg=0:1
4588 MCO:PIM:NODE REG=1
4590 MCO:BGN:STP
4591 MCO:BGN:INIT OK,TSP=1
4596 MCO:SLP:MS=750,SMS=0,I1=255,M1=255,I2=255,M2=255
4601 MCO:SLP:TPD
4602 MCO:SLP:WUP=-1
4636 TSF:MSG:SEND,51-51-0-0,s=0,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:20.2
4690 TSF:MSG:SEND,51-51-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:20.5
4755 TSF:MSG:SEND,51-51-0-0,s=2,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:20.4
7763 MCO:SLP:MS=750,SMS=0,I1=255,M1=255,I2=255,M2=255
7768 MCO:SLP:TPD
7770 MCO:SLP:WUP=-1
10898 MCO:SLP:MS=750,SMS=0,I1=255,M1=255,I2=255,M2=255
10902 MCO:SLP:TPD
10904 MCO:SLP:WUP=-1

[gohan]

I'm talking about adding code to your sketch so that it prints in serial monitor the values before they are sent for presentations and you debug from those, I can't debug it for you from here 😀

[Tim76]

@gohan oh.... ok..... pretty new at coding, but I guess you allready figured that out.....;-)