Where to get legit nRF24L01+ modules?

Nca78

I received my Ebyte modules, not a warranty of authenticity but the nrf chip has a square instead of a dot like all the fakes I have been using until now. I have a few standard SMD modules and a PA LNA version, I will try to make some basic range tests soon compared to the SMD clones.

Bogus Exception

OK! I followed your suggestions and tried itead. These are the pics of what I got 4 of (sorry no pro rig-just a loupe & module in one hand & mouse in the other!

(all are hosted on one of my servers, not here locally)

alt text

gohan

@Bogus-Exception let us know how they perform

Bogus Exception

@gohan I'll do my best to measure meaningful metrics between these & clones. Also, I have 4 eBytes coming (2x blue, 2x red)...

Bogus Exception

So far I've noticed on all versions of the legit nRF24 chips that the 'square' is actually 4 vertical lines, covering a square area, at the 'top left' of the chip.

Just tried over the past 2 hours to replace the clone in my MyController gateway with either the itead or ebyte legit modules, and neither one of them would communicate with the other nodes. I put the clone back in, and it worked. Weird.

Not like it matters much, but here is the sketch (all comments removed) using a BME280 and a light sensor module, on a Nano, USB powered:

#define MY_DEBUG
#define MY_RADIO_NRF24
#define MY_RF24_PA_LEVEL RF24_PA_LOW
#define MY_GATEWAY_SERIAL
#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif
#include <Adafruit_Sensor.h>
#include <Adafruit_BME280.h>
#define BME_SCK 13
#define BME_MISO 12
#define BME_MOSI 11
#define BME_CS 6
#define SEALEVELPRESSURE_HPA (1013.25)
const float ALTITUDE = 18;
Adafruit_BME280 bme(BME_CS); // hardware SPI
#define LIGHT_CHILD 0
#define BARO_CHILD 1
#define TEMP_CHILD 2
#define HUM_CHILD 3
boolean metric;
uint8_t decimals;
#include <MySensors.h>
MyMessage lightMsg(LIGHT_CHILD, V_LIGHT_LEVEL); // 0
MyMessage pressureMsg(BARO_CHILD, V_PRESSURE); // 1
MyMessage tempMsg(TEMP_CHILD, V_TEMP); // 2
MyMessage humMsg(HUM_CHILD, V_HUM); // 3
#define LIGHT_SENSOR_ANALOG_PIN 0
int lastLightLevel;
unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds)
void setup()
{
  #ifdef MY_DEBUG
    Serial.begin(115200);
  #endif
  decimals = 2;
  metric = getControllerConfig().isMetric; 
  bool status;
  status = bme.begin();
  if (!status) {
    #ifdef MY_DEBUG
      Serial.println("Could not find a valid BME280 sensor, check wiring!");
    #endif
    while (1);
  }
}
void presentation()
{
  sendSketchInfo("Master Nano", "1.0");
  present(LIGHT_CHILD, S_LIGHT_LEVEL);  // 0
  present(BARO_CHILD, S_BARO);          // 1
  present(TEMP_CHILD, S_TEMP);          // 2
  present(HUM_CHILD, S_HUM);            // 3
}
void loop()
{
  int16_t lightLevel = (1023-analogRead(LIGHT_SENSOR_ANALOG_PIN))/10.23;
  if (lightLevel != lastLightLevel) {
    #ifdef MY_DEBUG
      Serial.print(F("Sending lightMsg: "));
      Serial.println(String(lightLevel));
    #endif
    send(lightMsg.set(lightLevel));
    lastLightLevel = lightLevel;
  }
  float p_Mb = bme.readPressure() / 100.0F;
  float p_Hg = p_Mb / 33.86;
  #ifdef MY_DEBUG
    Serial.print(F("Sending pressureMsg: "));
    Serial.println(String(p_Hg));
  #endif
  send(pressureMsg.set(p_Hg, decimals));
  float t_C = bme.readTemperature();
  float t_F = (t_C * (9/5)) + 32;
  #ifdef MY_DEBUG
    Serial.print(F("Sending tempMsg: "));
    Serial.println(String(t_F));
  #endif
  send(tempMsg.set(t_F, decimals));
  float h_Pct = bme.readHumidity();
  #ifdef MY_DEBUG
    Serial.print(F("Sending humMsg: "));
    Serial.println(String(h_Pct));
  #endif
  send(humMsg.set(h_Pct, decimals));  
  #ifdef MY_DEBUG
    Serial.print(F("Sleeping for: "));
    Serial.println(String(SLEEP_TIME));
  #endif
  sleep(SLEEP_TIME);
}

It works with the clone... I am using a regulator board for the nRF24-the one it plugs into & breaks out the 8 pins...

Yveaux

@Bogus-Exception said in Where to get legit nRF24L01+ modules?:

So far I've noticed on all versions of the legit nRF24 chips that the 'square' is actually 4 vertical lines, covering a square area, at the 'top left' of the chip.

You cannot rely on the print of the nRF to distinguish fake from genuine. Nordic is fabless, so they use different factories to produce their chips, each with its own specific marking.

gohan

@Bogus-Exception may I ask why are you using spi for bme280 sensor instead of i2c?

Bogus Exception

@gohan I already have the 3 pins for SPI in use for the nRF, so adding the BME was just one more pin. Simply conserving pins.

Bogus Exception

@Yveaux Fair enough. I won't rel on that, but did want to mention the observation.
On a relatively side note, I got 4 SMD nRF24 cards from eByte, but can't locate any boards to mount them on! The holes are 1.27mm pitch, so I just ordered some 1.27mm headers.
Has anyone grabbed a board to surface mount solder them at this pitch?

NeverDie

@Bogus-Exception said in Where to get legit nRF24L01+ modules?:

@Yveaux Fair enough. I won't rel on that, but did want to mention the observation.
On a relatively side note, I got 4 SMD nRF24 cards from eByte, but can't locate any boards to mount them on! The holes are 1.27mm pitch, so I just ordered some 1.27mm headers.
Has anyone grabbed a board to surface mount solder them at this pitch?

What's the pitch on most other SMD nRF24L01+ modules? Is it also 1.27mm, or something else? I hadn't paid attention.

Bogus Exception

@NeverDie Great question. Mine look like these from a post earlier in this thread, and they are the first I've seen that didn't have their (breadboard-unfriendly) pinout.

alt text

NeverDie

Not sure if it's what you mean, but for prototyping purposes you could solder them to generic 1.27mm proto-board, such as this: https://www.aliexpress.com/item/6-X-8CM-spacing-1-27-universal-board-thickness-1-6mm-sided-HASL-PCB-test-board/32774106087.html?spm=a2g0s.9042311.0.0.eD40xE

gohan

I think there are adapters to solder the smd version and make them 8 pin compatible or there are generic adapters that can change the pitch

Nca78

@Bogus-Exception said in Where to get legit nRF24L01+ modules?:

On a relatively side note, I got 4 SMD nRF24 cards from eByte, but can't locate any boards to mount them on! The holes are 1.27mm pitch, so I just ordered some 1.27mm headers.
Has anyone grabbed a board to surface mount solder them at this pitch?

You can use NModule, the footprint highlighted in red color in the image below is compatible
alt text

https://www.openhardware.io/view/364/NModule

Bogus Exception

@kalina made these DIP-to-SMD-NRF24L01-adapter, but my need isn't enough quantity to buy the chemicals, pay someone to make a rum of them, or convince my wife that, "We'll sell them and make our money back!" :-[

Bogus Exception

@Nca78 Not just the module (10 for $15, right?), but the page concept is exactly what I am doing these days. Built in flexibility where it matters!
You've clearly spent a lot of time at my stage of tinkering with this!

alt text

Little touches like PA pinout, etc. makes this cake have more icing then cake! :o

NeverDie

@Bogus-Exception
I'm sure the Kalina adapter would be inexpensive if you purchased 3 through OSH PARK because the surface area is small.

Bogus Exception

@d00616 I have to ask...

How did you create this image?

d00616

@Bogus-Exception said in Where to get legit nRF24L01+ modules?:

How did you create this image?

The image is created with a medical X-Ray machine.

Bogus Exception

@NeverDie What I meant was, I don't have anything in 1.27mm, so now I've ordered enough stuff to keep my 2.54 and 2.0 company! :)

Where to get legit nRF24L01+ modules?

7

11.7k

11.2k

113.0k