Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

im quite confuse, the voltage sensor read the voltage at solar or at the battery..??

Faris Sabri II last edited by

Re: 12v Solar battery monitor
Reply Quote 0
1 Reply Last reply
Boots33 Hero Member last edited by @Faris Sabri II

@Faris-Sabri-II It reads the battery voltage.
Reply Quote 0
1 Reply Last reply
gohan Mod last edited by

by looking at the picture the voltage is measured near the battery, so I'd say it is the battery voltage
Reply Quote 0
1 Reply Last reply

3
Posts

745
Views

Log in to reply

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
BMP280 SPI Adafruit
My Project • • Matt

3

1
Votes

3
Posts

2128
Views

Hallo! Ich habe gerade meinen Aduino Nano mit einem GY-BME/P-280 verbunden über SPI verbunden. Im Sketch habe ich nur die PINS geändert und zwar auf: #define BMP_SCK 13 #define BMP_MISO 12 #define BMP_MOSI 11 #define BMP_CS 10 Ich bekomme aber bei der Ausgabe am seriellen Monitor nur "Hyroglyphen" zB 5��,�lh��}��'�O8��m�h,� Mit einem anderen Sketch funktioniert der Sensor einwandfrei. Auch mit einem anderen Nano dasselbe Ergebnis. Hat jemand eine Idee was das Problem sein könnte? Zusatzfrage da ich in C++ nicht so firm bin: Könnte es sein, dass MY_DEBUG oder MY_RADIO_NRF24 das problem verursacht. Was machen diese Definitionen eigentlich? Grüße
Wio-E5 (STM32 and SX1262)
My Project • • nagelc

2

1
Votes

2
Posts

21
Views

Quick Range Check on the WIO-E5-LE. The LE version uses only the low power PA, +14dBm max. Using the default settings except for 915MHz #define MY_SX126x_FREQUENCY (SX126x_915MHZ) #define MY_SX126x_LORA_SF LORA_SF7 #define MY_SX126x_LORA_BW LORA_BW_125 #define MY_SX126x_LORA_CR LORA_CR_4_5 I get about 190 meter range, just walking around the neighborhood, line of site except for some trees and power lines. No tuning on the antenna. Just using a 77.9mm wire. Not as dramatic as some have achieved with LoRa radio's, but plenty good enough for my house and yard : )
Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

1

2
Votes

1
Posts

15
Views

No one has replied
Nb of possible nodes in a mysensors networks with domoticz
My Project • • GLAB

18

0
Votes

18
Posts

128
Views

@OldSurferDude yeah, 10 virgin nodes powered up at the same time is a bad idea I seem to remember reading somwewhere here warning aginst that. If yu have node ID trust issues with Mysensors you should move your address to different locaion as 0x00 is used by Mysensors... just sayin..;)
Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

5

3
Votes

5
Posts

17
Views

@OldSurferDude thank you !

52
Online

11.5k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1