Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

NEED HELP SERIALPORT ,

zago1819 27 Dec 2017, 14:48 last edited by

I INSTALLED NODE RED AND WORKING. I INSTALL ALSO MODBUS SERIAL PORT BUT I CANT CONNECT WITH PLC
Reply Quote 0
1 Reply Last reply 27 Dec 2017, 15:11
serial port with plc delta 1
Loading More Posts
2
Posts

650
Views
Reply

Reply as topic
Log in to reply
mfalkvidd Mod 27 Dec 2017, 15:11 last edited by mfalkvidd 27 Dec 2017, 15:12 @zago1819

Hi @zago1819, and welcome to the MySensors community.

This community is about the MySensors library, so you might not get a lot of help about PLCs and Modbus.

Also, could you please write with normal characters instead of ALL CAPS? Most people interpret all caps as yelling, which certainly will get you nowhere.
Reply Quote 1
1 Reply Last reply

serial port with plc delta 1

2
Posts

650
Views

Log in to reply

2 out of 2

Suggested Topics

Welcome
Announcements • 23 Mar 2014, 08:24 • hek 2 Apr 2014, 14:39

8

0
Votes

8
Posts

3.2k
Views

2 Apr 2014, 14:39

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • 18 Oct 2024, 02:19 • OldSurferDude 18 Oct 2024, 02:19

1

0
Votes

1
Posts

13
Views

No one has replied
Nb of possible nodes in a mysensors networks with domoticz
My Project • 13 Jan 2025, 18:10 • GLAB 27 days ago

18

0
Votes

18
Posts

133
Views

27 days ago

@OldSurferDude yeah, 10 virgin nodes powered up at the same time is a bad idea I seem to remember reading somwewhere here warning aginst that. If yu have node ID trust issues with Mysensors you should move your address to different locaion as 0x00 is used by Mysensors... just sayin..;)
Long time test done with soil sensor!
My Project • 7 Jan 2025, 09:13 • Nicklas Starkel 13 Jan 2025, 09:10

5

4
Votes

5
Posts

27
Views

13 Jan 2025, 09:10

Wow @Nicklas-Starkel congrats, that sounds great! And thanks for the feedback. Would you mind sharing your setup? Regards, Edi
A low cost energy meter
My Project • 25 Jan 2024, 01:03 • OldSurferDude 12 Aug 2024, 06:03

7

1
Votes

7
Posts

49
Views

12 Aug 2024, 06:03

@OldSurferDude yes, you are correct. this sensor is capable of 50A continuous, which safely I would make it working at 40A max., but for such an important load as in your case I would go for a beefier one, like the ACS75x, 77x, but at this point I would also change the node's form factor for space and insulation reasons. On my application on the RV I have a max. curr. of 13A running on a AWG14-16 cable (European rules for RVs), so I did not ask myself too many questions beside, of course, safety. About the signal, it will be a sinusoidal signal swinging around Vcc/2. Vcc can be easily measured internally on the ATmega328. On all my DC sensors I measure Vcc at every loop, just before measuring the ADCs. Honestly, when the space is not an issue like in my RV, I would rather use a ring core current transformer, and I would get rid of noise, response time, power dissipation, but over all no need to cut any cable. Long story short, it has been a nice experiment and I used it for 6 months, and then I switched back to my RF-NANO based RS485-Modbus - Mysensors bridge connected to an off-the shelf power analyzer. Just for fun I attach a pic of my 12Vdc sensors installed on my RV. Forgive me for the spaghetti wiring on the right side, but this is an area that needs improvement.
Water Filtering and Sterilization and Hot Water Recirculation
My Project • 10 Aug 2024, 07:51 • fsgraz 12 Aug 2024, 05:25

5

3
Votes

5
Posts

17
Views

12 Aug 2024, 05:25

@OldSurferDude thank you !

0
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1