Sensbender Micro and v2.2 library
-
I have a somewhat modified sketch based on the Sensebender Micro sketch and this one failed to compile when changing to the v2.2 library. So I copied the original sketch from the homepage and also this one fails to compile when enabling MY_DEBUG. The error messages are numerous so it is pointless to add them here but a couple of examples are:
\Arduino\libraries\MySensors-master-v220_180209/core/MyOTAFirmwareUpdate.cpp:63:41: error: expected ')' before 'PRIX16'
OTA_DEBUG(PSTR("OTA:FRQ:FW REQ,T=%04" PRIX16 ",V=%04" PRIX16 ",B=%04" PRIX16 "\n"),
\Arduino\libraries\MySensors-master-v220_180209/MyConfig.h:1815:43: note: in definition of macro 'DEBUG_OUTPUT'
#define DEBUG_OUTPUT(x,...) hwDebugPrint(x, ##VA_ARGS) //!< debug
\Arduino\libraries\MySensors-master-v220_180209/core/MyOTAFirmwareUpdate.cpp:63:3: note: in expansion of macro 'OTA_DEBUG'
OTA_DEBUG(PSTR("OTA:FRQ:FW REQ,T=%04" PRIX16 ",V=%04" PRIX16 ",B=%04" PRIX16 "\n"),
As this is in the core code it is something I am unable to figure out myself, unfortunately. But as the compilation runs through without problems when disabling MY_DEBUG it is not any mayor issue until the debug output is needed.
-
What version of the Arduino IDE are you using? I Had a similar problem but I solved that with updating the IDE to the latest version (1.8.5).
@davidzh Do not know what is going on with my browser, I have replied to your question but cannot see this reply anywhere. Also i did not receive any notification about your question so my reply is late, sorry.
The issue showed up when compiling for library version 2.2 on Arduino 1.6.12. I will test with the latest version as you suggest, thank's a lot for the info. -
What version of the Arduino IDE are you using? I Had a similar problem but I solved that with updating the IDE to the latest version (1.8.5).
@davidzh A change to 1.8.5 did not help. But disabling My_Debug still works so the problem is not critical.
For the sake of clarity I have also tested with an unmodified Sensebender sketch and also this one gets compilation errors when enabling My_Debug. So the problem comes from the implementation of the debug code. -
@davidzh A change to 1.8.5 did not help. But disabling My_Debug still works so the problem is not critical.
For the sake of clarity I have also tested with an unmodified Sensebender sketch and also this one gets compilation errors when enabling My_Debug. So the problem comes from the implementation of the debug code.@mbj No problem!
Actually, I've encountered another issue. But I found that that may depend on the bootloader.
The first time I "solved" the problem was another board with a generic 328p breadboard bootloader (I apparently didn't pay attention when burning the BL for the various boards)
Last week I had a problem with a board with the Gert Sanders 328p bootloader when I couldn't enable the MY_DEBUG. When I changed the board type it compiled, but wouldn't upload because of the differences in baud rate.
I will probably have to reflash al boards withe the same bootloader but that means de-solder all radios ... 😣
When I have time again I will investigate further.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login