LoRa Gateway

[alexsh1]

OK, excellent. I have not tried lora coverage myself (apart from single channel GW for TTN). In fact I did not even built one for my home automation. I think the best usage of it are things like remote location sensors. I know a guy who is utilising lora for HAB (High Altitude Ballooning) projects - http://www.daveakerman.com/

I am trying to think about where at home I can utilise one, but so far RFM69 is covering everything for me. Having said that, your GW is a simple and minimalist one and I can probably build one just to tinker.

PS BTW, water leak sensors - I have a couple of z-wave sensors. They were not DIY, but the advantage is that they just work and look very nice.

[ricorico94]

Hi,
Seems a great project !
Can you clarify the difference with your previous minimalist gateway : the new one is linked to Domoticz controller through wifi, but how was the minimalist linked to controller ? Wasnt'it already through wifi ? Or do you mean this new approach enhances the wifi connectivity by using ESP-Link ? (to be frank, I don't really understand what makes ESP-Link so good, as I never investigated it)

br,
Ricorico94

[NeverDie]

@ricorico94 The main difference is that the newer project can use ESP-LINK on the ESP8266, whereas the first one can't. However, you are correct: with the right programming both can use wi-fi

[NeverDie]

Also, I've confirmed that ESP-LINK doesn't run on the ESP32, so the only way to use it is with an ESP8266 plus an additional MCU, which is what this newer version enables.

[ricorico94]

I think I could understand the wiring thanks to your other projects (the shield for ESP-link on Wemos D1 mini), but I'd appreciate if you could clarify it -just to make sure since I see the 90° connector on picture is not like the one in your shield)
Could you detail also the SW/scripts and settings you use ?
Thanks,
Ricorico94

[NeverDie]

@ricorico94
To overcome the overhang, I've since put everything onto a single shield for the ESP8266 D1 Mini:

[NeverDie]

Of course, another way to handle the overhang would be to make it overhang in the opposite direction, where the overhang wouldn't matter:
https://www.openhardware.io/view/273/ESP-LINK-ESP8266-WeMos-D1-Mini-Adapter-Board
That would work too.

[ricorico94]

This is even one step further as I understand you get rid of the sandwich Arduino pro mini by soldering directly an ATMEGA328p. It makes the overall setup much more dense indeed. Congratulations !

Could you share the details on software (scripts..) you used for the whole setup ?
I'm also interested in settings you use, because based on another thread, I had seen that some settings for RFM95 had an impact on error rates.

[NeverDie]

@ricorico94 said in LoRa Gateway:

software (scripts..) you used for the whole setup ?

Nothing meaningful to share as yet. I'm using RadioHead to verify that the hardware works as intended.

[NeverDie]

Currently priced at $3.01 per module with free shipping:
https://www.aliexpress.com/item/LoRa-Series-Ra-01-Spread-Spectrum-Wireless-Module-Ultra-10KM-433M-RF-Chip-SX1278/32799821469.html?spm=a2g0s.13010208.99999999.262.rCAs4B
https://www.aliexpress.com/item/LoRa-Series-Ra-02-Spread-Spectrum-Wireless-Module-Ultra-10KM-433M-RF-Chip-SX1278/32799769669.html?spm=a2g0s.13010208.99999999.265.rCAs4B

[NeverDie]

Epilog: the fully integrated ESP-LINK LoRa gateway has no antenna overhang and is working fine. :)

[alowhum]

Cool.

Have you seen these?
https://nl.aliexpress.com/item/RCmall-2-Sets-partij-LoRa32u4-II-Lora-Development-Board-Module-LiPo-Atmega328-SX1276-HPD13-868-MHZ/32832789857.html

[NeverDie]

Hadn't seen it. I'm lately of the mind that it's better to have everything (including sensors) integrated onto a single board.