Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

RGB LED strip (share your code)

vladimir last edited by

Hello!
In the continuation of the topic: RGB LED strip
I suggest to everyone who uses RGB LED strips to share their current code.
At the moment I'm using this one: https://forum.mysensors.org/topic/6765/rgb-led-strip/48
Reply Quote 0
1 Reply Last reply

1
Posts

957
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3310
Views

No one has replied
Home Assistant/MySensors quirks
Development • • OldSurferDude

1

0
Votes

1
Posts

8
Views

No one has replied
Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

3

1
Votes

3
Posts

25
Views

@mfalkvidd Thank you very much, that's exactly what I was looking for!
Radio waking up for no reason.
Development • • Sasquatch

3

0
Votes

3
Posts

37
Views

Over 4 years on, and my node ran continuously sending 4 messages every 5 minutes. It's 700mAh LiFePo4 battery voltage dropped from initial 3.45V to 3.24V, according to LiFePo4 voltge/SoC tables It's just under 40% left. 700*60% = 420mAh. 100 mAH per year. using library 2.40 and blob message I could cut usage to ~25mAh/year, not bad
Gateway without a radio
Development • • OldSurferDude

3

0
Votes

3
Posts

29
Views

@OldSurferDude yes, just run the configure command with --my-transport=none
MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

11

0
Votes

11
Posts

53
Views

@dpcons MQTT sounds intimidating and looks imitimidating when you see all of the options available. Here's the scenario: You want to send a message. That's the -m option followed by a space and the message between " " the location, topic, is a tree, -t option, separated by forward slash / eg. MyRootTopic/MyTopicsSub/MyTopicSubSub It's as easy as that if your broker, the MQTT service (program) is on the same computer as the sending program. Usually it's not. Specifiy the location, the host, of the broker with the -h option followed by the host name or IP address The retain option, -r is important but explaining it is beyone the scope of this message Receiving, subscribing, to a topic is just the same, but you wouldn't have the -m message If you subscribe from the command line, the subscribe function waits indefinitely for messages published to the subscribed topic (unless you use the -C option) ^C to terminate the command. A tamotized device with the MQTT configured will create a number of topics on the broker. Home Assistant will see this automatically, if you have the Tasmota and MQTT Integrations installed. The MySensors MQTT gateway takes care of MQTT communication for a MySensors device. Again the MySensors and MQTT integrations. I use both. -OSD

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Home Assistant/MySensors quirks
Development • • OldSurferDude

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

Radio waking up for no reason.
Development • • Sasquatch

Gateway without a radio
Development • • OldSurferDude

MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

20
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

RGB LED strip (share your code)

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

Home Assistant/MySensors quirks Development • • OldSurferDude

Counting Incoming and Outgoing Messages from a Gateway Development • • Trand

Radio waking up for no reason. Development • • Sasquatch

Gateway without a radio Development • • OldSurferDude

MQTT-Help me understand about the MQTT Gateway. Development • • dpcons

20Online

11.7kUsers

11.2kTopics

113.0kPosts