Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

RGB LED strip (share your code)

vladimir last edited by

Hello!
In the continuation of the topic: RGB LED strip
I suggest to everyone who uses RGB LED strips to share their current code.
At the moment I'm using this one: https://forum.mysensors.org/topic/6765/rgb-led-strip/48
Reply Quote 0
1 Reply Last reply

1
Posts

951
Views

Suggested Topics

ATC and repeating nodes
Development • • eiten

3

0
Votes

3
Posts

54
Views

oh well... N2 was broken, it did not switch between RX and TX. We are discussing the issue over at Heltec community. Thank you.
PlatformIO and Sensebender
Development • • andy5211d

6

1
Votes

6
Posts

59
Views

Tested this today: it works fine! In the meanwhile,I also found this: https://forum.mysensors.org/topic/2725/sensebender-micro/30 My platformio.ini file: [platformio] src_dir = WindowOpenSensor [env:sensebender-micro] platform = atmelavr board = pro8MHzatmega328 framework = arduino monitor_speed = 19200 lib_deps = 548 ; MySensors src_build_flags = -DMY_RF24_CHANNEL=100
MYSBootloader 1.3 pre-release & MYSController 1.0.0beta
Development • ota myscontroller mysbootloader • • tekka

183

13
Votes

183
Posts

84703
Views

Hello bootloader support ATMEGA328PB now this uC is cheaper than 328p? Best regards
Sample sketch for test node including hardware and software acknowledgement
Development • • grumpazoid

9

0
Votes

9
Posts

40
Views

@mfalkvidd said in Sample sketch for test node including hardware and software acknowledgement: char messagestring[100]; message.getString(messagestring); Serial.println(messagestring); @mfalkvidd Fantasic. Thank you. That is what I was looking for . It works now !!!
[SOLVED] 2.3.1 TO 2.3.2 MyConfig.h got changed
Development • • grumpazoid

3

0
Votes

3
Posts

41
Views

@Yveaux Yes I had manually changed MyConfig.h to reflect the channel number I use. I thought I had read that was the way to do it. Okay thanks for putting me straight. Good to know it was just normal behaviour. I'll add it to each of my sketches in future. Thanks.
GUIDE - NRF5 / NRF51 / NRF52 for beginners
Development • • alowhum

59

10
Votes

59
Posts

17499
Views

@idanronen , I am not an expert but did manage to accomplish what you are doing about a year ago. I can tell you that you are supposed to get two com ports from BMP. Also, where your screen shot says "SW-DP scan failed" means BMP cannot find any 'targets' on the nrf52. You should get back something that looks like this from the scan: Available Targets: No. Att Driver 1 ARM Cortex-M 2 Nordic nRF52 Access Port I performed this operation on ~10 nrf52832 and only one failed the scan. I never found out how to solve it. Also, your use of the attach command is incorrect. You appear to be trying to attach the com port 13. If the swdp_scan had worked corrrectly, you would then attach the target that shows up in the scan. In my example output, it would be "attach 2" - the nRF52 Access Port. That adds what I know, hope it helps a bit.
Support for new Arduino Hardware platform: WavGat UNO R3 compatible board
Development • • evb

10

0
Votes

10
Posts

4963
Views

@konbaasiang Thanks for the update. I've still the wavgat uno R3 boards somewhere, so I will try it
Press inclusion button to reboot after 10 sec, ESP8266 only
Development • • Clone Tv

1

0
Votes

1
Posts

13
Views

No one has replied

ATC and repeating nodes
Development • • eiten

PlatformIO and Sensebender
Development • • andy5211d

MYSBootloader 1.3 pre-release & MYSController 1.0.0beta
Development • ota myscontroller mysbootloader • • tekka

Sample sketch for test node including hardware and software acknowledgement
Development • • grumpazoid

[SOLVED] 2.3.1 TO 2.3.2 MyConfig.h got changed
Development • • grumpazoid

GUIDE - NRF5 / NRF51 / NRF52 for beginners
Development • • alowhum

Support for new Arduino Hardware platform: WavGat UNO R3 compatible board
Development • • evb

Press inclusion button to reboot after 10 sec, ESP8266 only
Development • • Clone Tv

261
Online

9.6k
Users

10.2k
Topics

106.1k
Posts

RGB LED strip (share your code)

Suggested Topics

ATC and repeating nodes Development • • eiten

PlatformIO and Sensebender Development • • andy5211d

MYSBootloader 1.3 pre-release & MYSController 1.0.0beta Development • ota myscontroller mysbootloader • • tekka

Sample sketch for test node including hardware and software acknowledgement Development • • grumpazoid

[SOLVED] 2.3.1 TO 2.3.2 MyConfig.h got changed Development • • grumpazoid

GUIDE - NRF5 / NRF51 / NRF52 for beginners Development • • alowhum

Support for new Arduino Hardware platform: WavGat UNO R3 compatible board Development • • evb

Press inclusion button to reboot after 10 sec, ESP8266 only Development • • Clone Tv

261Online

9.6kUsers

10.2kTopics

106.1kPosts