Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Water Flow Sensor with SonOff

Bur Han last edited by

Hey !! Can anyone guide me about how to get water flow pulses from sonoff GPIO14 ?
Reply Quote 0
1 Reply Last reply
Bur Han last edited by

no one ??
Reply Quote 0
1 Reply Last reply
bjacobse last edited by

Did you try the below forum?
http://support.iteadstudio.com/support/discussions
Reply Quote 0
1 Reply Last reply

3
Posts

926
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3304
Views

No one has replied
[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

3

0
Votes

3
Posts

17
Views

Thanks, I'll keep this in mind if I decide to debug it. I realized that I am also tired of patching the gateway through to the doctor container inside an LXC so now I am looking at creating an esp gateway. Just need to check if I can find a pcb on here. Thanks again!
(SOLVED) Sensebender Gateway and HomeAssistant: where does the battery level come from?
Development • • pikim

1

0
Votes

1
Posts

11
Views

No one has replied
MYSController with MQTT Gateway (via Node Red)
Development • • slt1

1

1
Votes

1
Posts

11
Views

No one has replied
Sensebender Gateway (SAMD21)
Development • • pikim

10

0
Votes

10
Posts

55
Views

Just for completeness: the right way to do this is to add the json under ~/.platformio/boards and the other files as described in https://community.platformio.org/t/how-use-a-same-chip-but-with-different-environment/18082/4
MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

6

0
Votes

6
Posts

27
Views

@bgunnarb I like @eiten 's solution for you. Personally, I am not a fan of using cloud/public brokers. Thus I am curious about your system and there is something about it from which I can learn. I would like to understand why you cannot deploy your own mosquitto broker. I see your set up as 3 sensor groups defined by the channel used #define MY_RF24_CHANNEL ChannelOfSensorGroup Each sensor group has some number of sensors and one MQTT GW on ESP8266. On the MQTT side, do you distinguish between gateways by using a different host name? Something like: #define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway-nOf3-out" #define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway-nOf3-in" #define MY_MQTT_CLIENT_ID "mysensors-nOf3" #define MY_HOSTNAME "ESP8266_MQTT_GW_nOf3" //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 #define MY_CONTROLLER_URL_ADDRESS "test.mosquitto.org" #define MY_PORT 1883 I must assume your controller (aka Home Assistant) discriminates between through which gateway the data is to flow by way of the different topic names. If my "something like" is correct, then changing brokers is changing the IPaddress/URL in your gateways and in your controller (though if the controller is Home Assistant, it may be a bother because the device-id's may change which will make a mess of all the work you've done in HA. This is why I like @eiten 's solution.) I hope it's all working for you again. OSD

Water Flow Sensor with SonOff

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

(SOLVED) Sensebender Gateway and HomeAssistant: where does the battery level come from?
Development • • pikim

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

Sensebender Gateway (SAMD21)
Development • • pikim

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

12
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Water Flow Sensor with SonOff

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000' Development • • kiesel

(SOLVED) Sensebender Gateway and HomeAssistant: where does the battery level come from? Development • • pikim

MYSController with MQTT Gateway (via Node Red) Development • • slt1

Sensebender Gateway (SAMD21) Development • • pikim

MQTT GW on ESP8266 supporting SSL/TLS? Development • esp8266 mqtt gw • • bgunnarb

12Online

11.4kUsers

11.1kTopics

112.7kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

(SOLVED) Sensebender Gateway and HomeAssistant: where does the battery level come from?
Development • • pikim

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

Sensebender Gateway (SAMD21)
Development • • pikim

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

12
Online

11.4k
Users

11.1k
Topics

112.7k
Posts