OpenHAB 2.5 MySensors Serial Gateway - How to install

Jic

I still have problem with with org.openhab.binding.mysensors-2.2.0-SNAPSHOT.jar and org.openhab.binding.mysensors-2.3.0-SNAPSHOT.jar
I get always de Mysensors Serial Gateway offline with this error

2018-03-01 21:36:47.880 [DEBUG] [col.serial.MySensorsSerialConnection] - Connecting to /dev/ttyMySensorsGateway [baudRate:115200]
2018-03-01 21:36:47.890 [ERROR] [col.serial.MySensorsSerialConnection] - No such port: /dev/ttyMySensorsGateway
gnu.io.NoSuchPortException: null
	at gnu.io.CommPortIdentifier.getPortIdentifier(CommPortIdentifier.java:273) [25:com.neuronrobotics.nrjavaserial:3.12.0.OH]
	at org.openhab.binding.mysensors.internal.protocol.serial.MySensorsSerialConnection.establishConnection(MySensorsSerialConnection.java:51) [195:org.openhab.binding.mysensors:2.3.0.201802141500]
	at org.openhab.binding.mysensors.internal.protocol.MySensorsAbstractConnection.connect(MySensorsAbstractConnection.java:148) [195:org.openhab.binding.mysensors:2.3.0.201802141500]
	at org.openhab.binding.mysensors.internal.protocol.MySensorsAbstractConnection.run(MySensorsAbstractConnection.java:127) [195:org.openhab.binding.mysensors:2.3.0.201802141500]
	at java.util.concurrent.Executors$RunnableAdapter.call(Executors.java:511) [?:?]
	at java.util.concurrent.FutureTask.runAndReset(FutureTask.java:308) [?:?]
	at java.util.concurrent.ScheduledThreadPoolExecutor$ScheduledFutureTask.access$301(ScheduledThreadPoolExecutor.java:180) [?:?]
	at java.util.concurrent.ScheduledThreadPoolExecutor$ScheduledFutureTask.run(ScheduledThreadPoolExecutor.java:294) [?:?]
	at java.util.concurrent.ThreadPoolExecutor.runWorker(ThreadPoolExecutor.java:1142) [?:?]
	at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:617) [?:?]
	at java.lang.Thread.run(Thread.java:745) [?:?]

I back to org.openhab.binding.mysensors-2.1.0-SNAPSHOT.jar and now it's working again. Any ideas?

Thanks

FlipFlap3

@jic Nope sry, BUT.. I am going to do a fresh install again today. Will check if I can get it to work and make updates to this howto where needed.

FlipFlap3

2.3 snapshot doesn't work. 2.2 does

Updated opening post for step by step instruction on installing openhab2.2 with mysensors 2.2 serial gateway binding. If you have any questions, just post them here.

Jic

Seem it's working know.

Thanks

FrozenYack

I am trying to follow these instructions to set up OpenHab with the MySensors Serial Gateway, but ran into a problem when installing the Java (Third command.). Here is a copy of the command and error:

pi@openhabpi:~ $ sudo apt-key adv --keyserver hkp://keyserver.ubuntu.com:80 --recv-keys EEA14886
Executing: /tmp/apt-key-gpghome.3nAEDiCNLy/gpg.1.sh --keyserver hkp://keyserver.ubuntu.com:80 --recv-keys EEA14886
gpg: failed to start the dirmngr '/usr/bin/dirmngr': No such file or directory
gpg: connecting dirmngr at '/tmp/apt-key-gpghome.3nAEDiCNLy/S.dirmngr' failed: No such file or directory
gpg: keyserver receive failed: No dirmngr

Please let me know if I missed something.

BTW, this is using the raspbian stretch lite version, dated 2018-03-13.

Thank you!

GreyLinux

@FlipFlap3
Firstly well done for the brilliant instructions . I too have been attempting to use Openhab with my sensors over the last year and to be honest although I've had relative success, because of the limited amount of, up to date and accurate tutorials its been a steep slope to climb. Currently I have Openhabian installed on a Raspberry pi with a Gateway connected to the I/O pins of the Pi and a couple of temp sensors connected ( all be it with difficulty ). It's setup as an Ethernet Gateway but I did try once to setup it up as a serial gateway, unsuccessfully I might add. Out of interest if I did re- install using your setup instructions, Is a serial Gateway better or easier in any way ? it does seem like the most supported option of the 3 for most people on the forum .

FlipFlap3 · BTW, this is using the raspbian stretch lite version, dated 2018-03-13.

@frozenyack Sorry, I can't remember seeing an error like that before.

FlipFlap3

@greymarvel said in OpenHAB 2.2 MySensors Serial Gateway - How to install:

@FlipFlap3
Firstly well done for the brilliant instructions . I too have been attempting to use Openhab with my sensors over the last year and to be honest although I've had relative success, because of the limited amount of, up to date and accurate tutorials its been a steep slope to climb. Currently I have Openhabian installed on a Raspberry pi with a Gateway connected to the I/O pins of the Pi and a couple of temp sensors connected ( all be it with difficulty ). It's setup as an Ethernet Gateway but I did try once to setup it up as a serial gateway, unsuccessfully I might add. Out of interest if I did re- install using your setup instructions, Is a serial Gateway better or easier in any way ? it does seem like the most supported option of the 3 for most people on the forum .

Thanks

Sorry for late response (busy with anual reporting lately).

I have tried MTTQ first myself, but I didn't get things working smoothly. 2nd attempt was with serial gateway. Even though I had some problems at first, I did manage to get it working. I had a hard time finding a good tutorial though, so I wrote down the steps I took carefully. Reason for me to put it here was to have a personal backup for my notes and if it would be helpful for anyone else that would be an awesome bonus ;-)

I didn't try ethernet gateway yet cause I am happy with the current setup.

joaoabs

Hi,

The mysgw seems to be creating a link to the wrong TTY.
When I connect the arduino gateway, I get the /dev/ttyUSB1 device.

Insert Code Herepi@nettemp:~/MySensors $ ls /dev/tty*
/dev/tty    /dev/tty15  /dev/tty22  /dev/tty3   /dev/tty37  /dev/tty44  /dev/tty51  /dev/tty59  /dev/tty9
/dev/tty0   /dev/tty16  /dev/tty23  /dev/tty30  /dev/tty38  /dev/tty45  /dev/tty52  /dev/tty6   /dev/ttyAMA0
/dev/tty1   /dev/tty17  /dev/tty24  /dev/tty31  /dev/tty39  /dev/tty46  /dev/tty53  /dev/tty60  /dev/ttyUSB0
/dev/tty10  /dev/tty18  /dev/tty25  /dev/tty32  /dev/tty4   /dev/tty47  /dev/tty54  /dev/tty61  /dev/ttyUSB1
/dev/tty11  /dev/tty19  /dev/tty26  /dev/tty33  /dev/tty40  /dev/tty48  /dev/tty55  /dev/tty62  /dev/ttyprintk
/dev/tty12  /dev/tty2   /dev/tty27  /dev/tty34  /dev/tty41  /dev/tty49  /dev/tty56  /dev/tty63
/dev/tty13  /dev/tty20  /dev/tty28  /dev/tty35  /dev/tty42  /dev/tty5   /dev/tty57  /dev/tty7
/dev/tty14  /dev/tty21  /dev/tty29  /dev/tty36  /dev/tty43  /dev/tty50  /dev/tty58  /dev/tty8

Then I start the mysgw and a new tty is created: "/dev/ttyMySensorsGateway", which looks nice. However, the mysgw returns lots of errors:

mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0
mysgw: Serial port /dev/ttyMySensorsGateway (115200 baud) created
mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:DIS
mysgw: TSF:TDI:TSL
mysgw: TSM:INIT
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=2
mysgw: TSM:FAIL:DIS
mysgw: TSF:TDI:TSL

Then I go check what is wrong an I see the pointer wasn't created towards "/dev/ttyUSB1", but "/dev/pts/1":

pi@nettemp:~/MySensors $ ls -larth /dev/ttyMySensorsGateway 
lrwxrwxrwx 1 root root 10 Apr 26 18:27 /dev/ttyMySensorsGateway -> /dev/pts/1

Taking a look into the /dev/ttyUSB1 directly I can see it is fine, the problem is the GW software on the Raspberry PI that is pointing towards the wrong tty:

pi@nettemp:~ $ stty -F /dev/ttyUSB1 cs8 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke noflsh -ixon -crtscts
pi@nettemp:~ $ cat /dev/ttyUSB1 
0;255;3;0;9;0 MCO:BGN:INIT GW,CP=RNNGAS--,VER=2.2.0
0;255;3;0;9;0;255;3;0;9;0 MCO:BGN:INIT GW,CP=RNNGAS--,VER=2.2.0
0;255;3;0;9;26 SGN:PER:OK
0;255;3;0;9;64 SGN:INI:BND OK
0;255;3;0;9;67 TSM:INIT
0;255;3;0;9;69 TSF:WUR:MS=0
0;255;3;0;9;77 TSM:INIT:TSP OK
0;255;3;0;9;79 TSM:INIT:GW MODE
0;255;3;0;9;82 TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;87 MCO:REG:NOT NEEDED
0;255;3;0;14;Gateway startup complete.
0;255;0;0;18;2.2.0
0;255;3;0;9;91 MCO:BGN:STP
0;255;3;0;9;98 MCO:BGN:INIT OK,TSP=1

Any idea of how to make this work?

Where can I see the alternatives for the "
./configure --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyMySensorsGateway --my-rf24-channel=69 --my-transport=nrf24 --my-serial-groupname=tty --my-config-file=/etc/mysensors.dat" command?

Thanks,

FlipFlap3

@joaoabs

I had to re-install myself and found my how to wasn't 100% correct for OpenHAB 2.4 so I updated it.

Works with OpenHAB 2.4 and @TimO 's 2.4 jar. Kudos to him for this!

nizoo91

My god, had everything almost working and now my PaperUI disappeared on me for the 2nd time.....

I was trying to remove and reinstall MySensors but this is the second time this happens to me :/ I don't want to re-install everything again! Any ideas on how I can get the paperUI back?

I tried removing my "addons.config" from "/var/lib/openhab2/config/org/openhab"
didn't help, also opened it and it didn't have the paperui option, manually added it and still didn't work :(

I am about to give up on OpenHab lol, is there any easier controller to setup? I heard good things about Domoticz but I JUST got OH to kinda work! I was just receiving the wrong values and thought it could of been because of some errors, so decided to re-compile MySensors and install it again.. and then poooof, the whole UI isn't there anymore :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm: :face_palm:

EDIT: oh great, even more stuff disappeared, now I only have HOMEBUILDER left! :man-facepalming:

TimO

@nizoo91 Stick to addons.cfg in /etc/openhab2/conf/services and don't fiddle with the file you mentioned above.
With package=standard (look for the examples in the comments) the UIs should reappear.

nizoo91

@flipflap3 said in OpenHAB 2.4 MySensors Serial Gateway - How to install:

feature:install openhab-transport-serial

can you please add

"feature:install esh-io-transport-mqtt"

to the tutorial it is required to get it to work even in Serial :)

FlipFlap3

@nizoo91 Just found out myself as well that this was missing. Thanks!

iamtheghost

@flipflap3 said in OpenHAB 2.4 MySensors Serial Gateway - How to install:

sudo apt-get install oracle-java8-installer

This package has been removed and can't be installed as instructed in the tutorial. As of April, I believe it was removed from that repo.

Reading package lists... Done
Building dependency tree
Reading state information... Done
Package oracle-java8-installer is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source

E: Package 'oracle-java8-installer' has no installation candidate

Unsure of how to proceed.

TRS-80

@iamtheghost,

I realize it's been few months, but I will post this anyway. As I also recently went through the same ordeal.

Thanks to OP for posting an easy to follow guide.

I found the official install instructions at OpenHAB quite good: https://www.openhab.org/docs/installation/linux.html

...with one exception. Currently, it seems there is some bug going on with their build system or something. I actually had lodged an issue of my own (and even had submitted a PR to correct the documentation) before someone replied, pointing me to the root issue. So for the time being, instead of using https://dl.bintray.com/openhab/apt-repo2 location, you should use https://openhab.jfrog.io/openhab/openhab-linuxpkg repository location.

Further, if you care about issues such as software freedom (which I do a great deal) you might want to consider installing Azul/Zulu Java 8 (make sure it's 8!) which I have done, instead of Oracle Java. Azul's (also excellent) instructions can be found linked from the OpenHAB Linux install instructions. And that would also solve your missing repo problem, obviously.

alphaHotel

@trs-80 said in OpenHAB 2.4 MySensors Serial Gateway - How to install:

Currently, it seems there is some bug going on with their build system or something. I actually had lodged an issue of my own (and even had submitted a PR to correct the documentation) before someone replied, pointing me to the root issue. So for the time being, instead of using https://dl.bintray.com/openhab/apt-repo2 location, you should use https://openhab.jfrog.io/openhab/openhab-linuxpkg repository location.

I ran into the same thing. Specifically, to get around this, the second instruction under the OpenHAB portion of the original post can be substituted with this:

echo 'deb https://openhab.jfrog.io/openhab/openhab-linuxpkg stable main' | sudo tee /etc/apt/sources.list.d/openhab2.list

EDIT: I've just noticed that they've updated the Package Repository Installation instructions to add the command above.

Further, if you care about issues such as software freedom (which I do a great deal) you might want to consider installing Azul/Zulu Java 8 (make sure it's 8!) which I have done, instead of Oracle Java. Azul's (also excellent) instructions can be found linked from the OpenHAB Linux install instructions. And that would also solve your missing repo problem, obviously.

If using Zulu Java, beware that the repos are not being maintained and are behind (see reference for manual instructions).

I used OpenJDK 8 for java with sudo apt install openjdk-8-jdk-headless.

I'm using an Ethernet gateway (on a separate Raspberry Pi) though which is a twist on all of this.

--Allen

FlipFlap3

Updated to OpenHAB 2.5 with step-by-step instructions
switched to Zulu Java

OpenHAB 2.5 MySensors Serial Gateway - How to install

10

11.7k

11.2k

113.1k