[SOLVED] Raspberry Pi serial gateway NRF24 - !TSM:INIT:TSP FAIL
-
This is what i use to configure my raspberry pi3 to work vi serial.
--my-transport=rf24 --my-rf24-pa-level=RF24_PA_LOW --my-rf24-irq-pin=15 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18
Built using this page. https://www.mysensors.org/build/raspberry
And when recieving this error "Dec 31 11:07:50 DEBUG !TSM:INIT:TSP FAIL" I had found a bad jumper that I had used. Hope This helps!
-
As kebibg said you must also configure the pins for CE and CS. The configure i used was :
--my-transport=rf24 --my-rf24-pa-level=RF24_PA_LOW --my-gateway=serial --my-serial-is-pty --my-serial-port=/dev/ttyUSB020 --my-rf24-ce-pin=22 --my-rf24-cs-pin=24 --my-rf24-irq-pin=15 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18
Also you must connect MISO to pin 21, Mosi to pin 19 and CLK to pin 23 on raspberry
-
As kebibg said you must also configure the pins for CE and CS. The configure i used was :
--my-transport=rf24 --my-rf24-pa-level=RF24_PA_LOW --my-gateway=serial --my-serial-is-pty --my-serial-port=/dev/ttyUSB020 --my-rf24-ce-pin=22 --my-rf24-cs-pin=24 --my-rf24-irq-pin=15 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18
Also you must connect MISO to pin 21, Mosi to pin 19 and CLK to pin 23 on raspberry
@badisensors said in Raspberry Pi serial gateway NRF24 - !TSM:INIT:TSP FAIL:
As kebibg said you must also configure the pins for CE and CS. The configure i used was :
--my-transport=rf24 --my-rf24-pa-level=RF24_PA_LOW --my-gateway=serial --my-serial-is-pty --my-serial-port=/dev/ttyUSB020 --my-rf24-ce-pin=22 --my-rf24-cs-pin=24 --my-rf24-irq-pin=15 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18
Also you must connect MISO to pin 21, Mosi to pin 19 and CLK to pin 23 on raspberry
The only pin's I needed to specify on my setup was IRQ and leds. The GW has been working great for 2+ years on my raspberry pie 3b with nrf24+.
Why did I Not have to specify them in my setup? did something change? I am running version 2.3.1.
-
-
2 years ago were you using version 2.3.1 ?
@badisensors 2.0.0 not really 2 years ago more like 1 1/2. Why do you ask?
-
Because in 1.5-2 years many things are changing. Did you try my config?
-
Because in 1.5-2 years many things are changing. Did you try my config?
@badisensors I did try your config and it works just as mine does. Just wondering if the adding this --my-rf24-ce-pin=22 --my-rf24-cs-pin=24 to the config was necessary. But from the my test it is not. Thanks.
-
If we use pin 22 for CE and pin 24 for CS it is not necessery to declare as you said. But if we want to use other pins we need to declare. I havent try though with other pins.
-
I changed cables, get new NRF24L01+ PA/LNA and make clean install of rasbian. Nothing helped, but then out of nothing it started to work (at least no fail). Its a mystery to me why. Thank you all for help.
pi@raspberrypi:~/MySensors $ sudo ./bin/mysgw Jan 12 10:05:42 INFO Starting gateway... Jan 12 10:05:42 INFO Protocol version - 2.3.1 Jan 12 10:05:42 DEBUG Serial port /dev/ttyUSB020 (115200 baud) created Jan 12 10:05:42 DEBUG MCO:BGN:INIT GW,CP=RNNGL-Q-,REL=255,VER=2.3.1 Jan 12 10:05:42 DEBUG TSF:LRT:OK Jan 12 10:05:42 DEBUG TSM:INIT Jan 12 10:05:42 DEBUG TSF:WUR:MS=0 Jan 12 10:05:42 DEBUG !TSM:INIT:TSP FAIL Jan 12 10:05:42 DEBUG TSM:FAIL:CNT=1 Jan 12 10:05:42 DEBUG TSM:FAIL:DIS Jan 12 10:05:42 DEBUG TSF:TDI:TSL Jan 12 10:05:52 DEBUG TSM:FAIL:RE-INIT Jan 12 10:05:52 DEBUG TSM:INIT Jan 12 10:05:52 DEBUG !TSM:INIT:TSP FAIL Jan 12 10:05:52 DEBUG TSM:FAIL:CNT=2 Jan 12 10:05:52 DEBUG TSM:FAIL:DIS Jan 12 10:05:52 DEBUG TSF:TDI:TSL ^CJan 12 10:05:53 NOTICE Received SIGINT pi@raspberrypi:~/MySensors $ sudo ./bin/mysgw Jan 12 10:14:30 INFO Starting gateway... Jan 12 10:14:30 INFO Protocol version - 2.3.1 Jan 12 10:14:30 DEBUG Serial port /dev/ttyUSB020 (115200 baud) created Jan 12 10:14:30 DEBUG MCO:BGN:INIT GW,CP=RNNGL-Q-,REL=255,VER=2.3.1 Jan 12 10:14:30 DEBUG TSF:LRT:OK Jan 12 10:14:30 DEBUG TSM:INIT Jan 12 10:14:30 DEBUG TSF:WUR:MS=0 Jan 12 10:14:30 DEBUG TSM:INIT:TSP OK Jan 12 10:14:30 DEBUG TSM:INIT:GW MODE Jan 12 10:14:30 DEBUG TSM:READY:ID=0,PAR=0,DIS=0 Jan 12 10:14:30 DEBUG MCO:REG:NOT NEEDED Jan 12 10:14:30 DEBUG MCO:BGN:STP Jan 12 10:14:30 DEBUG MCO:BGN:INIT OK,TSP=1 Jan 12 10:14:30 DEBUG TSM:READY:NWD REQ Jan 12 10:14:30 DEBUG TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:```
